beyerdynamic MMX 200 Wireless Multi Platform Gaming Headset User Manual

: June 13, 2024
: beyerdynamic

Table of Contents

SAFETY INSTRUCTIONS
Disposal
CONFORMITY AND GUARANTEE
TECHNICAL SPECIFICATIONS
FCC / IC REGULATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MMX 200 Wireless Multi Platform Gaming Headset
User Manual

SAFETY INSTRUCTIONS

Please read these safety instructions carefully and completely before using the product.
Please observe all instructions given, especially those concerning the safe use of the product.
Please also observe the detailed operating instructions for this product. The instructions can be downloaded from the Beyer dynamic website at www.beyerdynamic.de.
Do not use the product if it is defective.
Intended use
Only use the product as described in the product manual. Beyer dynamic accepts no liability for damage to the product or injury to persons caused by careless, improper or incorrect use of the product, or by use for purposes not specified by the manufacturer.
Beyer dynamic is not liable for damage to USB devices that do not comply with the USB specifications. Beyer dynamic is not liable for damage resulting from connection interruptions due to batteries being empty or too old, or due to exceeding the Bluetooth® transmission range.
Please also observe the relevant country-specific regulations before using the product.
Adjusting the volume
High volumes and long listening can permanently damage your hearing.
Before putting on the headset, set the volume to minimum.
Do not use the headset at high volume for a long time. When listening and speaking normally with a headset, your voice should still be perceptible.
In case of tinnitus, decrease the volume. If necessary, consult a doctor.
We would like to point out that excessively high volumes and long listening times may cause hearing damage.
Hearing impairments are irreversible, so always ensure an adequate volume level.
It is advisable to keep listening times at high volumes as short as possible.
Damage from liquids
Liquid penetration can damage the headset.
Make sure that no liquids penetrate the headset (e.g. when cleaning).
Solvent-based or aggressive cleaning agents can damage the surfaces of the headset or the cable.
Do not use solvent-based or aggressive cleaning agents.
Risk of swallowing
Keep small parts, such as product, packaging and accessories, away from children and pets. They constitute a choking hazard if swallowed!
Using the batteries
Danger from heat, water and mechanical stress
Excessive heat, water and mechanical stress may cause explosion, heat, fire, smoke or fumes. Injuries and irreversible damage to the battery may result.
Do not expose the battery to excessive heat, fire or extremely low air pressure. There is a risk of explosion, fire, smoke or gas.
Do not subject the battery to mechanical stress (e.g. crushing). This may cause irreversible damage to the battery, or explosion or injury.
Do not open the housing or remove the battery.
Only use a USB 2.0/3.0 standard- compliant 5 V power supply to charge the battery via the integrated USB Type-C port.
Storing the battery
If the battery is not going to be used for an extended period, set the charge level to approximately 50 % of the maximum capacity and store it at temperatures up to max. 30 °C.
Charging
Disconnect the USB connecting cable from the charging unit once the device is fully charged.
Environmental conditions
Do not expose the product to rain, snow, liquids or moisture.

Disposal

This symbol on the product, in the operating instructions or on the packaging means that the electrical and electronic devices must be disposed of separately from household waste at the end of their life-cycle.
Always dispose of used equipment in accordance with applicable regulations.
For the return of old equipment, batteries and rechargeable batteries, there are free collection points or a free return to Beyer dynamic, as wells other acceptance points for reuse The addresses are available at the local city or municipal administration.
Dealers for electronic equipment are generally obliged to take back waste electrical/electronic equipment free of charge. This obligation also applies to sales via remote communication.
For further information, please contact the local authorities or the dealer from whom the product was purchased.
Disposal of batteries
Dispose of batteries separately after use from the product in accordance with applicable regulations. They must not be disposed of in household waste. The return is free of charge for consumers/end users.
Before disposal, discharge and remove the batteries.
CAUTION: For this product a non-destructive removal of the battery by the end user is not possible. Please contact Beyer dynamic or consult independent professional staff.
On the internet at www.beyerdynamic.com/mmx- 200wireless you will find instructions for battery removal (for professional staff only).

CONFORMITY AND GUARANTEE

EU/UK Declaration of conformity
beyerdynamic hereby declares that this radio transmission device complies with the EU Directive 2014/53/EU and the UK Directive “The Radio Equipment Regulations 2017”.
The full text of the EU/UK declaration of conformity can be found on the Internet at: www.beyerdynamic.com/cod.
Warranty conditions
beyerdynamic provides a limited guarantee for the original beyerdynamic product you have purchased.
You can find detailed information about Beyer dynamic’s warranty conditions on the Internet at www.beyerdynamic.de/service/garantie.
PRODUCT REGISTRATION
You can register your MMX 200 wireless online at www.beyerdynamic.com/mmx-200-wireless by entering the serial number.

TECHNICAL SPECIFICATIONS

MMX 200 wireless

Bluetooth® frequency range	2,400 – 2,483.5 MHz
Transmitting power	10 dBm
Operating temperature range	-10 to +60 °C
Charging temperature range	+10 to +45 °C
Battery type: lithium-ion battery	3.7 V, 900 mAh

Low Latency Wireless Adapter

Bluetooth frequency range	2,400 – 2,483.5 MHz
Transmitting power	10 dBm
Operating temperature range	-10 to +60 °C

You can find more detailed information about the technical specifications online at: www.beyerdynamic.com/mmx-200-wireless
REGISTERED TRADEMARKS
The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc. and all use of these trademarks by Beyer dynamic is under license. Other trademarks and trade names are the property of the respective owners.
USB Type A, USB Type B and USB Type C are trademarks of USB Implementers.

FCC / IC REGULATION

Model/HVIN: MMX 200 wireless
FCC ID: OSDMMX200
Canada IC: 3628C-MMX200
Model/HVIN: Low Latency Wireless
Adapter
FCC ID: OSDLLWA
Canada IC: 3628C-LLWA

Responsible Party — U.S. Contact Information
Beyer Dynamic Inc.
56 Central Ave.
NY 11735 Farmingdale
USA
631-293-3200
info@beyerdynamic-usa.com

NOTICE:
This device complies with Part 15 of the FCC Rules [and with Industry Canada licensee- exempt RSS standard(s)]. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-003(B) / NMB-003 (B)
Radiofrequency radiation exposure information:
This equipment has been tested and complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications made to this equipment not expressly approved by Beyer dynamic may void the FCC and user authorization to operate this equipment.
Approval IDs
Due to its dimensions, the Low Latency Wireless Adapter is not labelled with the approval IDs for the USA, Canada, Japan and Australia.
For the headset you will find the approval IDs for the USA, Canada, Japan and Australia on the left ear cup under the ear pad. You can remove the ear pad by turning it anti-clockwise. THIRD PARTY LICENSES
For more information on 3rd party licenses, please go to: https://www.beyerdynamic.de/media/downloads/headphones/manual/Licenses_MMX_200_wireless.md https://www.beyerdynamic.de/media/downloads/headphones/manual/Licen- ses_Low_Latency_Wireless_Adapter.md

Beyer dynamic GmbH & Co. KG
Theresienstraße 8 · 74072 Heilbronn / Germany
Phone +49 7131 617-300
E-Mail info@beyerdynamic.com
www.beyerdynamic.com
For further distributors worldwide,
please go to www.beyerdynamic.com
Non-contractual illustrations.
Subject to change without notice.
Änderungen vorbehalten.
EN-DE-FR-ES-IT-SV-JA-TH-ZH 2 · Safety, compliance and warranty · MMX 200 wireless · (06.23)