SUPERMICRO 741P-TR Super Server User Guide

SUPERMICRO 741P-TR Super Server User Guide

Board Layout

Quick Reference Table

LED4, LED7M.2 LEDs (for M.2-C1, M.2-C2Blinking Green: Device Working
LED6| Unit Identifier (UID) LED| Solid Blue: Unit Identified
LEDBMC| BMC Heartbeat LED| Blinking Green: BMC Normal (Active), Solid Green: (During BMC Reset or during a Cold Reboot)
LEDPWR| Power LED| LED On: Onboard Power On
Connector| Description
---|---
BT1| Onboard CMOS Battery BMC_LAN Dedicated BMC LAN Port
COM1| Rear I/O COM Port
FAN1 – FAN6, FANA, FANB| CPU/System Fan Headers
-SATA0, I-SATA1| Intel PCH Powered I-SATA 3.0 Ports with support of SuperDOM devices *DOM: Disk on Module
JBP_I2C1| 4-pin BMC External I²C Header
JCOM2| Front Accessible COM Port Header
JF1| Front Control Panel Header
JFP2| Front Accessible VGA Connection Header
JIPMB1| 4-pin BMC External I²C Header (for Inlet Temperature Sensor)
JL1| Chassis Intrusion Header
JNCSI1| NC-SI (Network Controller Sideband Interface) Connector
JNVI2C1| NVMe SMBus I²C Header with hot-plug support
JPCIE1 (SLOT1), JPCIE6 (SLOT6)| PCIe 5.0 x8 Slots (SLOT1: supported by CPU1, SLOT6: supported by CPU2)
JPCIE2/3 (SLOT2/3), JPCIE4/5 (SLOT4/5)| PCIe 5.0 x16 Slots (SLOT2/3: supported by CPU1, SLOT4/5: supported by CPU2)
JPI2C1| Power System Management Bus (SMBus) I²C Header
JPWR1, JPWR2, JPWR4| 8-pin Power Connectors
JPWR3| 24-pin ATX Power Connector
JS1 (SATA 0 – SATA7)| SlimSAS x8 Connector with support of eight Intel PCH SATA 3.0 connections (RAID 0, 1, 5, and 10 supported)
JSD1, JSD2| SATA DOM Power Connectors
JSTBY1| 5V Standby Power Header
JSD1, JSD2| SATA DOM Power Connectors
JSTBY1| 5V Standby Power Header
JTPM1| Trusted Platform Module/Port 80 Header
JUIDB1| Unit Identifier (UID) Switch / BMC Reset Button
LAN1, LAN2| Ethernet LAN (RJ45) Port 1 and Port 2 (1G LAN support on X13DEI and 10G LAN support on X13DEI-T)
M.2-C1, M.2-C2| PCIe 4.0 x2 NVMe M.2 Slots supported by CPU1 (with support of M-Key 2280 and 22110)
P1_NVME0/1 (JNVME1) P1_NVME2/3 (JNVME2)| MCIO x8 Connectors supported by CPU1 with four PCIe 5.0 x4 NVMe connections
P2_NVME4/5 (JNVME3)| MCIO x8 Connector supported by CPU2 with two PCIe 5.0 x4 NVMe connections
S-SGPIO1| Serial General Purpose I/O Header (for I-SATA0/1 SuperDOM support)
USB0/1| USB 2.0 Header with support of two USB connections
USB2| Internal USB 2.0 Vertical Type-A Connector
USB3/4 (3.0)| Back Panel USB 3.0 Ports (5Gbps, Type-A)
USB5/6 (3.0)| Back Panel USB 3.0 Ports (5Gbps, Type-A)
USB7/8 (3.0)| USB 3.0 Header with support of two USB connections
USB7/8 (3.0)| USB 3.0 Header with support of two USB connections
VGA| Rear I/O VGA Port

Memory

DIMM Population Guidelines for Optimal Performance 4TB memory capacity with 16 DIMMs of 256GB 3DS RDIMM/RDIMM DDR5 ECC memory. For optimal memory performance, follow the instructions listed in the tables below when populating memory modules.

Note: Memory speed and capacity support depends on the processors used in the system.

Key Parameters for DIMM Configurations

Parameters| Possible Values
Number of Channels per Socket| 1, 2, 4, 6, 8
Number of DIMMs per Channel| 1DPC (1 DIMM Per Channel) or 2DPC (2 DIMMs Per Channel)
DIMM Type| RDIMM and 3DS RDIMM
DIMM Construction| non-3DS RDIMM Raw Cards: A (2Rx4), C (1Rx4), D (1Rx8), E (2Rx8) 3DS RDIMM Raw Cards: A (4Rx4, 8Rx4) 9×4 RDIMM Raw Cards: B (2Rx4), F (1Rx4)
Compatible and Incompatible Type in a Channel and a System

DIMM Type| RDIMM| RDIMM 3DS| 9×4 RDIMM
RDIMM| Compatible| Incompatible| Incompatible
RDIMM 3DS| Incompatible| Compatible| Incompatible
9×4 RDIMM| Incompatible| Incompatible| Compatible

Note: 1DPC applies to 1 SPC (Sockets Per Channel) or 2 SPC implementation.

DDR5 Memory Support for the 4th Generation Intel Xeon Scalable Processors

Type| Ranks Per DIMM
& **Data Width
(Stack)| DIMM Capacity (GB)| Speed (MT/s); DIMM Per Channel 1DPC (Note)| Voltage (V); (DPC)
2DPC
16GB| 1.1V
RDIMM| SRx8 (RC D)| 16GB| 4800| 4400
SRx4 (RC C)| 32GB
SRx4 (RC F) 9×4| 32GB
DRx8 (RC E)| 32GB
DRx4 (RC A)| 64GB
DRx4 (RC B) 9×4| 64GB
RDIMM 3DS| (4R/8R) x4 (RC A)| 2H-128GB
4H-256GB
LRDIMM/LRDIMM-3DS**| N/A| N/A| Not Supported| Not Supported

Note: This memory configuration is recommended by Supermicro for optimal memory performance. Please use this configuration to maximize your memory performance.

DDRS Memory 1 CPU| Population Table for X13 DP Motherboards (with 16 DIMMs installed) Memory Population Sequence
---|---
1 CPU & 1 DIMM| P1-DIMMA1 or P1-DIMME1 or P1-DIMMB1 or P1-DIMMF1
1 CPU & 2 DIMMs| P1-DIMMA1 / P1-DIMMG1 or P1-DIMMC1 / P1-DIMME1
1 CPU & 4 DIMMs| P1-DIMMA1 / P1-DIMMC1 / P1-DIMME1 / P1-DIMMG1
1 CPU & 6 DIMM| P1-DIMMA1 / P1-DIMMC1 / P1-DIMMD1 / P1-DIMME1 / P1-DIMMF1 / P1-DIMMG1 or P1-DIMMA1 / P1-DIMMB1 I P1-DIMMC1 / P1-DIMME1 / P1-DIMMG1 I P1-DIMMH1 or P1-DIMMB1 / P1-DIMMC1 / P1-DIMMD1 / P1-DIMME1 / P1-DIMMF1 / P1-DIMMH1 or P1-DIMMA1 / P1-DIMMB1 I P1-DIMMD1 / P1-DIMMF1 / P1-DIMMG1 I P1-DIMMH1
1 CPU & 8 DIMMs| P1-DIMMA1 / P1-DIMMB1 / P1-DIMMC1 / P1-DIMMD1 / P1-DIMME1 / P1-DIMMF1 / P1-DIMMG1 / P1-DIMMH1
2 CPUs (Recommended)| Memory Population Sequence
2 CPUs & 2 DIMMs| CPU1:P1-DIMMA1,CPU2:P2-DIMMA1 or CPU1:P1-DIMME1,CPU2: P2-DIMME1 or CPUI: P1-DIMMB1.CPU2: P2-DIMMB1 or CPU1: P1-DIMMF1,CPU2: P2-DIMMF1
2 CPUs & 4 DIMMs| CPU1: P1-DIMMA1 / P1-DIMMG1CPU2: P2-DIMMA1 / P2-DIMMG1 or CPU1: P1-DIMMC1 / P1-DIMME1CPU2: P2-DIMMC1 / P2-DIMME1
2 CPUs & 8 DIMMs| CPU1:P1-DIMMA1 / P1-DIMMC1 / P1-DIMME1 / P1-DIMMG1CPU2: P2-DIMMA1 / P2-DIMMC1 / P2-DIMME1 / P2-DIMMG1
2 CPUs & 12 DIMMs| CPUI: P1-DIMMA1/P1-DIMMC1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMG1
CPU2: P2-DIMMA1/P2-DIMMC1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMG1 CPU1:P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMME1/P1-DIMMG1/P1-DIMMH1
CPU2:P2-DIMMA1/P2-DIMMB1/P2-DIMMC1/P2-DIMME1/P2-DIMMG1/P2-DIMMH1 CPU1: P1 – DIMMB1/P1 – DIMMC1/P1 – DIMMD1/P1 – DIMME1/P1 – DIMMF1/P1 – DIMMH1 CPU2: P2-DIMMB1/P2-DIMMC1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMH1 CPUI: P1-DIMMA1/P1-DIMMB1/P1-DIMMD1/P1-DIMMF1/P1-DIMMG1/P1-DIMMH1
CPU2: P2-DIMMA1/P2-DIMMB1/P2-DIMMD1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1
2 CPUs & 16 DIMMs| CPU1: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMG1/P1-DIMMH1
CPU2 P2-DIMMA1/P2-DIMMB1/P2-DIMMC1/P2-DIMMD1/P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1

Front View & Interface

Rear View

Rotating the Optional Storage Module

Rotating the Storage Module for Rack Mounting

1. Open the chassis cover.
2. Locate the storage module and disconnect any cables from the storage module to any component in the chassis.
3. Push the storage module release lever. This lever unlocks the storage module.
4. Grasp the external edges of the storage module and pull the unite from the chassis.
5. Turn the storage module 90 degrees.
6. Reinsert the module into the chassis and reconnect the cords.

CPU/Heatsink Installation

Processor Carrier Assembly

Heatsink SNK-P0088P (for CPU1 and CPU2)

SP XCC and SP MCC Carrier View

Note:

Thermal grease is pre-applied on new heatsinks. No additional thermal grease is needed. CPU carrier is optional, Please select CPU carrier by CPU model. (E1A for XCC, E1B for MC)

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning before connecting system to power supply. http://www.supermicro.com/about/policies/safety_information.cfm

WARNING
To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets. If any CPU socket empty, install protective plastic CPU cap

CAUTION
Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the system will not operate.

For more information go to : http://www.supermicro.com/support

References

• Support | Supermicro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>