UNIVERSAL AUDIO V230523A UA Bock 167 Microphone PSU User Guide
- June 13, 2024
- Universal Audio
Table of Contents
UNIVERSAL AUDIO V230523A UA Bock 167 Microphone PSU User Guide
Introduction
The UA Bock 167 microphone continues Universal Audio’s proud tradition of timeless craftsmanship. Lovingly handbuilt at the UA Custom Shop in Santa Cruz, California, your new microphone is designed to deliver uncompromising quality and a lifetime of musical inspiration.
This microphone is a high-quality large-diaphragm condenser with vacuum tube electronics and continuously variable directivity. Featuring a dual membrane K67 capsule and a large core output transformer to dramatically increase low frequency response and headroom, the UA Bock 167 sounds rich and full.
Designed and engineered by David Bock, the UA Bock 167 provides a wider range of controls versus a vintage U67. This makes it a natural choice for singers, acoustic instruments, drums, and voiceovers.
Safety
Before using this unit, be sure to carefully read the applicable items of these operating instructions and the safety suggestions. Afterwards, keep them for future reference.
Take care to follow the warnings indicated on the unit, as well as in the operating instructions.
Important Safety Instructions
Read and follow all instructions. Heed all warnings. Keep these instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat source such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Only use with attachments/accessories specified by the
manufacturer.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
UA BOCK 167 PSU does not contain a fuse or any other userreplaceable parts.
Used electrical and electronic equipment should not be mixed with general household waste. Please dispose in accordance with local regulations.
Hazardous voltage enclosed. Do not open, will cause shock or burn. If servicing is needed, disconnect power and contact Universal Audio customer support.
UA Bock 167 Power Supply Unit
Your UA Bock 167 includes a high quality PSU that is custom designed exclusively for the Bock 167 mic. The PSU is factory-configured for the AC input voltage in the region where it is sold. There are no fuses or other user replaceable parts inside the unit.
For the UA Bock 167 User Guide, visit help.uaudio.com
Getting Started
Place the UA Bock 167 microphone in its included shockmount on a stable mic stand. Connect the power supply to AC, then connect the included six-pin XLR cable from power supply to microphone.
Note: The power supply should be powered off before connecting or disconnecting the microphone. After switching on the power supply, allow the tube several minutes to warm up before use.
The Bock 167’s polar response pattern is adjusted by the continuously variable remote control on the power supply. Rotate the control fully counterclockwise for omni response, or fully clockwise for figure-8 response. Set the control to noon (straight up) for cardioid polar response.
For customer support, visit help.uaudio.com
UA Bock 167 PSU Specifications
Input
100 VAC
115 VAC
220/230 VAC
Output
130 VDC @ 0.75 mA
5 VDC @ 132 mA
Power Supply Pinouts
Pin 1: Audio (-)
Pin 2: Audio (+)
Pin 3: Pattern
Pin 4: Heater (5VDC)
Pin 5: B+ (130VDC)
Pin 6: Ground
Case: Shield
Connectors
6-Pin XLR (mic)
3-Pin XLRM (power supply)
Max Operating Temp
40° C
Power Rating
8.2 W
Safety Standards
UL 62368-2
EN 62368-1
Universal Audio, Inc.
4585 Scotts Valley Drive, Scotts Valley, CA 95066
www.uaudio.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>