NINJA REAMi Deluxe 11-in-1 Ice Cream and Frozen Treat Maker User Guide

NINJA REAMi Deluxe 11-in-1 Ice Cream and Frozen Treat Maker

Assembly & Processing

1. Plug in unit first
   Unit will not run if outer bowl is installed before unit is plugged in.

2. Install Deluxe Pint Remove lid from Deluxe Pints and check that ingredients have not been frozen at an angle. Place Deluxe Pint with frozen base in outer bowl.

3. Install Creamerizer™ Paddle Press and hold paddle latch on top of outer bowl lid, then insert paddle in bottom of lid. Release latch to secure paddle.

4. .Install lid Position tab of lid just slightly to right of outer bowl handle so lines on lid and handle align. Rotate lid clockwise to lock.
   NOTE
   If control panel will not illuminate, ensure unit is properly assembled. See troubleshooting section of the safety instructions if install light is illuminated.

5. Install outer bowl After plugging in unit, place outer bowl on base with handle centered on unit. Twist handle to the right to raise platform and lock bowl in place (signaled by a click).

6. Select program Press Power. Select a processing mode (TOP, FULL, or BOTTOM), then turn dial to select a program and press dial to begin processing.

7. Remove bowl When program is complete, hold release button on left of motor base and twist bowl handle clockwise, then pull away from unit to remove.
   NOTE
   TOP and BOTTOM processing zones are only available with SCOOPABLE programs.

8. Remove lid
   Press the lid unlock button and twist to remove lid.
   OPTIONAL PROCESSING
   Use a spoon to create a1 1/2-inch wide hole that reaches the bottom of the processed ingredients. Add chopped or broken mix-ins to the hole. Select the same processing mode, then select MIX-IN.

9. If not adding mix-ins, RE-SPIN can be used on a crumbly or powdery output to make it creamy. RE-SPIN is often needed for very cold bases. Do not RE-SPIN before using MIX-IN program. Select the mode prior to selecting RE-SPIN.

Disassembly & Cleaning

Remove Deluxe Pint & paddle
Lift pint out of outer bowl. Rinse outer bowl lid to remove any sticky residue or pieces wedged in the paddle. Remove paddle by pressing paddle latch on top of lid. All parts are top-rack dishwasher safe and can also be hand-washed.
Fruit Punch Slushi
PREP: 3 minutes
FREEZE: 24 hours
PROGRAM TIME: 5 minutes
MAKES: 2 servings
INGREDIENTS
For Freezing

• 1/2 cup fruit punch powdered drink mix 1
• 3/4 cup (14 ounces) warm water

DIRECTIONS
For Freezing
Place the fruit punch powder into an empty CREAMi® Deluxe Pint. Pour the warm water into the pint up to the DRINKABLE FREEZE FILL line.
Combine mixture until the drink powder is completely dissolved. Place storage lid on Deluxe Pint and freeze for 24 hours.
For Processing
Pour-in: water, alcohol, or juice
For Processing
Remove Deluxe Pint from freezer and remove lid. Add pour-in to DRINKABLE POUR-IN line. Refer to previous pages for Assembly & Processing instructions.
Select FULL, then use the dial to select SLUSHI. When processing is complete, transfer slushi to a glass and serve immediately.
TIP
If your pour-in contains alcohol, select FROZEN DRINK.
NOTE
PREFER MORE SIPPABLE? If you prefer a thinner frozen drink after processing, simply add 2–4 additional tablespoons of your desired pour-in, then select RE- SPIN.

Perfectly Personalized Ice Cream

PREP: 5–10 minutes
FREEZE: 24 hours
PROGRAM TIME: 2 minutes
MAKES: 6 servings
INGREDIENTS

• 1 1/2 tablespoons (3/4 ounce) cream cheese
• 1/2 cup granulated sugar
• Flavoring: 1 1/2 teaspoons extract of choice OR 3 tablespoons cocoa powder
• 1 cup plus 2 tablespoons heavy cream
• 1 1/2 cups whole milk
• 1/3 cup of your favorite mix-ins (optional)

PICK YOUR FLAVOR
Vanilla extract
Mint extract Almond extract Fruit extract Cocoa powder
MAKE IT DAIRY-FREE Use vegan cream cheese for cream cheese, unsweetened coconut cream for heavy cream, and unsweetened oat milk for milk. Whisk the coconut cream until smooth, then add the remaining ingredients.
Microwave cream cheese for 10 seconds. Add sugar and flavor, then whisk the mixture until it looks like frosting. Slowly mix in heavy cream and milk until sugar is dissolved. Pour base into CREAMi® Deluxe Pint. Place storage lid on Deluxe Pint and freeze for 24 hours. Remove lid from frozen Deluxe Pint. Refer to previous page for Assembly & Processing instructions. Select processing mode (FULL, TOP, or BOTTOM), then select ICE CREAM.

PICK YOUR MIX-INS TO ADD A PERSONAL TOUCH

Prepare 1/3 cup of mix-ins, which can include your favorite crushed candies, frozen fruits, chopped nuts, chocolate pieces, and more. With a spoon, create a 1 1/2-inch wide hole that reaches the bottom of the processed ingredients. Add mix-ins to the hole. Select the mode previously processed, then select the MIX-IN program.
NOTE
Make two flavors from one base. See page 14 of Inspiration Guide to get started.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>