DENLER DFLv3 Smart Door Lock User Manual

DENLER DFLv3 Smart Door Lock

Scan the QR Code to register your product for hassle-free warranty services.

IMPORTANT NOTE
We recommend keeping at least 1 mechanical key outside your home. So, in case of emergency, you will be able to unlock the smart lock. This is helpful when there is any kind of electronic failure in lock.

Product Dimensions

Lock Elements

Product Specifications

Keypad Functions

Lock Setup Menu

Adding new user

***Touch the keypad to wake up lock and touch “#” to enter system menu. Enter your new 6-Digit Admin Password & press “#”, Enter again and press “#” to confirm. If you have already added admin, enter your admin password to enter system menu. Now select “1.New User” by touching number 1 on keypad. Where you can Add Face, Fingerprint, RFID Card & PIN in con nuous addi on mode. Keep adding user Fingerprint, PIN and card one by one. A?er selec ng add use if you don’t enter anything lock will go in Add Face mode To add Admin User select op on

1. Add Admin (Create at least 1 admin user for lock, User ID 1 to 10 are reserved for admin and other users with get ID from 11 to 99) and to add other users selec on op on
2. Add User

Adding PIN, RFID or Fingerprint

If you select “Add Admin” or “Add User”, this screen will appear with message “Enter unlock information”. Here you can enter any of the user biometric information like either you can enter 6-DIgit Number or touch the RFID card near number “5” on the keypad or adjust the face in front of lock as guided by voice prompt. You can set 6 Digit numeric password. After entering numeric password system will voice prompt “Please Enter Again” enter the same password again to verify. Then, you will see an “Add Success” message on screen with voice prompt “Success”

Adding Face ID

If you select “Add Admin” or “Add User”, the message “Enter unlock information” will appear. Wait for few seconds for lock to go in face addi on mode. Adjust your face position in front of camera as guided by system voice prompt. Then, you will see “Add Success” message on screen with voice prompt “Success”

Deleting User

Just like adding a new user you can delete the users from lock. It can be done by using the ID assigned to user or you can verify user using the fingerprint of that particular user. Select *# then admin password # to enter system menu.
Now select op on “2.Delete User” by touching number 2 on keypad. Where you can add delete user. On this screen, select op on 1.Verify Delete then apply fingerprint/PIN of the user to delete. Select op on 2.Delete by ID to delete user by entering ID assigned to user.

NOTE : In case of a temporary user like Maid, remember the User ID while adding fingerprint or PIN. So, you can delete this user even when user is not present at the me of dele on. You can directly delete user with the help of user ID. Else, you have to delete all the user and add again.

Door Direction, Date & Auto-Lock Setup

Now select number “3” on keypad for System se?ngs. Where you can setup Date & Time, Door Direc on, Auto-Lock etc
Select the number “1” to change the date on lock. Enter the date using keypad number.
Select number “1” to change door direcon [L] for le? and [R] for right door direction. Select “2” to set closing me to [OFF] / [10S] / [15S] / [20S] / [30S] / [60S] / [120S]

Face Recognition Motion Sensor Setup

IMPORTANT NOTE
Door direc on setup is not required if your door lock func on is working properly i.e. when you press lock button on the kepad, lock bolts are coming out from lockbody/mor se and when you unlock, they are going back inside the lockbody.
Face Recogni on Mo on Sensor Setup Select number “Door Set” in system menu. Then select “1.Sensor” to turn [ON] or [OFF] mo on detec on sensor. “2.Distance” to set distance sensi vity [N] Near or [F] Far. “3.Speed” to [S] / [N] / [F]. Voice” to turn [ON] or [OFF] system voice prompt.

Factory Reset

IMPORTANT NOTE : Factory reset will delete all the user data including fingerprints, face, RFID cards, PINS. Your lock will get disconnected from you Wi-Fi network and mobile app as well. You have to reconfigure all the se?ngs a?er factory reset.

Touch the keypad to wake up lock and touch # to enter system menu. Select “3.System Se?ng” then “4.Restore”. Press “” to cancel restore and “#” to confirm factory restore. “Recovering…” message will be displayed.
A?er successful factory restore “Clean Success” message will be displayed on the screen with voice prompt “Success”

Dual or Single Verifica on Mode

Select “3.System Setting” then “3.Func on Set” to select verifica on mode. Select “2.Doub Auth Set” and press “1” to Disable and “2” to enable Dual authen ca on mode

Mobile App Setup

IMPORTANT NOTE: Distance between Smart Lock and Wi-Fi router should be less than 15 feet. Make sure your Smartphone is connected with 2.4Ghz Wi-Fi network only (Does not support 5Ghz Wi-Fi Network). Loca on/GPS and Bluetooth is turned ON. Scan the following QR code to download “Xhome” mobile app for Android or iOS smartphones. Connect mobile to 2.4Ghz Wi-Fi Network, turn ON Bluetooth & Loca on/GPS. Click Sign Up & create account with Xhome app, if already registered click Login. While installing app give all permission or access to mobile app when asked. i.e loca on, files and search nearby devices (If asked) else it will not detect smart lock in app.

Scan QR code to as per your device type i.e. android or iOS to download Xhome mobile ap

1. Open Xhome app & click “Accept” to proceed for using this app. And allow all the access permissions if asked while installing

2. Click “Create Account” if you have not registered any account in Xhome app before.

3. Enter valid email ID, set password (Do not use special characters in password) & click “Get CAPTCHA” Check you email inbox for captcha, enter the captcha and click register

4. After successful login, click “+” icon at the right top corner of Xhome app and click “Add Device” to proceed.

5. Click “Smart E-Lock” then on the next screen Click “Join Wi-Fi by QR”

6. After clicking “Join Wi-Fi by QR” Now you have to acvate Network Configura on mode on the smart lock. On smart lock keypad Select “3.System Setting” then
   “3.Func on Set” to select verifica on mode. Select “1.Net Config”

7. A?er “Configuring” message on lock click “CONFIRM THAT ENTERED CONNECTED MODE” App will display your Wi-Fi network details, verify the details and click “NEXT”

8. QR code will be displayed on the next screen, hold your phone around 20cm in front of camera un l you hear single BEEP sound

9. During this step you can see your QR code position on the inner lock display to adjust QR code in the given marking posi ons

10. After successfully connec ng lock with app, you will see this op on to set the device name.

11. On the home screen of Xhome app you can see various lock features. Click Play button to start video or Click unlock icon to unlock remotely

12. In the settings sec on, you can setup Power Saving Mode, No fica ons, Remote Unlock , Firmware Upgrade etc.

13. In the power-saving mode sec on you can set Normal Standby to access live camera stream any me or Trigger mode to ac vate camera video stream only when bell icon is pressed on smart lock.

14. You will get the no fica on screen to start video and unlock when visitor presses bell icon the smart lock

15. After star ng intercom through no fica on you will se various op ons like unlock, capture photo and talk with visitor

Sharing lock with another smart-phone

To share access, lock must connected with Xhome app first. Create account of 2nd user in Xhome app with different email ID (Not the same as Admin user). Click Friends & Add Friends bu?on as shown in image 1, then enter the Email ID of 2nd user used to create account in Xhome app. Click Account then Share, select the lock to share then select the email ID of 2nd user and click Save. Now, the 2nd user will be able to see lock added in Xhome app.

Frequently Asked Ques ons (FAQs)

Does face recognition work for faces with beard?
3D face recognition does not properly for face with beards and it cannot recognize face structure pointers properly.

After installa on, the lock is not turning on or no response when keypad is touched
In this case, check whether the batteries are charged or not.

Unable to register fingerprint
Make sure fingers and fingerprint sensor on the smart lock is clean and there is no sign of dirt or oil stains. (Fingerprints of kinds below 5 Yrs and aged people may not get recognized because their fingerprints are not very clear)

Smart lock draining the battery faster
Keeping the mo on sensor con nuously ON and using the video func on too frequently can drain out ba?ery faster than usual.

Lock bolts are stuck and working forcefully only by hand
If your door slams when lock bolts are outside, this will bent lock bolts and either make them stuck outside or affects its func onality. In this case you have to contact Denler and purchase a new lock body.

References

• Smart Door Lock, Digital Door Lock, Wi-Fi Doorbell | Denler

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>