VISUAL COMFORT RL 5670 Paxton 24 Ring Chandelier Instruction Manual
- June 17, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT RL 5670 Paxton 24 Ring Chandelier Instruction Manual
ASSEMBLY INSTRUCTIONS
Paxton 24” Ring Chandelier
Item # RL 5670
NOTICE
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Cutters
Wire Strippers
Measuring Tape
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (B) from canopy (J) by removing screws (I).
-
Install mounting plate (B ) to the junction box and secure with mounting screws (E).
-
Wrap supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten.
NOTE: It is imperative that the fixture is grounded. -
Gently set fixture on a flat, non-abrasive surface to adjust fixture hanging wires.
-
To adjust each hanging wire loosen screws (H) on either side of the cable lock nut ( G ) and adjust to desired length. Once complete re-secure screws (H) and repeat steps with the remaining wires. (See diagram 2)
-
After fixture height is achieved shorten the wires by using a pair of cutters (not included), leaving 8” of wire length to connect to the driver (D).
NOTE: Final leveling in later step will only allow for small adjustments. Make sure fixture height and fixture level are accurate before cutting wires.
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. -
Remove outer housing of wire by making a neat cut all the way around, about 1” from the end. Once cut is made, remove and discard the 1” piece of housing, exposing the electrical wires.
NOTE: Make sure not to cut too deep into housing or electrical wires could become damaged. -
Separate wires and strip insulation on each 5/8″.
-
Install driver (D ) to canopy (J) and secure with screws (E).See diagram 3.
-
Connect fixture neutral wire (black) to driver (D) output wire (black) using wire nut (A).
-
Connect fixture hot wire (red) to driver (D) output wire (red) using wire nut (A ).
CAUTION: Do not reverse the hot and neutral connections. -
Run safety cable through hole on back of mounting plate (B). Loosen cable lock and install to end of safety cable. Insert other end of cable through the cable lock and tighten ends with a screwdriver to secure. (see diagram 4)
-
Connect driver (D) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
-
Connect driver (D) input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. -
Install canopy (J) to mounting plate (B) and secure with screws (I).
-
To level fixture, unscrew cap nut (L) , feed fixture wire through stopper (K) and then re-secure cap nut (L). Repeat as needed with other wires. (See diagram 2)
Care Instructions: Clean only
with a soft dry cloth or feather duster. Do not use abrasive or chemical
agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>