airplex FIT918 HD Euro Low Roof Cab Sunvisor Instructions
- June 13, 2024
- airplex
Table of Contents
airplex FIT918 HD Euro Low Roof Cab Sunvisor
Product Information
- Product Name: FIT918 Automotive Sunvisor
- Manufacturer: Airplex Industries Limited
- Address: 21 Saleyards Road, Otahuhu, Auckland, New Zealand
- Website: www.airplex.com
- Contact: Phone: +64 (9) 276-9826, Fax: +64 (9) 276-9836, Email: info@airplex.com
- Part Number: SV117F
- Compatibility: Fuso FV FS HD Euro Low Roof Cab
Tools Required:
- Drill
- 3mm & 9mm drill bits
- Tec screws & bit (for temporary fastening)
- Alan key for 6mm machine screw
- Rivnut / Nutsert tool
- Marker pen
- CRC Soft Seal or similar rust prevention
Product Usage Instructions
- Hold the sunvisor to the front of the truck to identify the 2 innermost bolts above the windscreen that align with the 2 large sunvisor holes.
- Remove these 2 bolts from above the windscreen.
- Offer sunvisor to cab of truck again. Use M8 bolts supplied to temporarily fix sunvisor to cab using identified holes.
- Check alignment of sunvisor. Make sure it is level with cab.
- Working from the centre towards the outer ends, firmly hold sunvisor against the cab and temporarily fix to the cab using the tec screws or similar. Drill all holes.
- Remove sunvisor. On the truck, drill all new holes out to 9mm.
- Apply anti-rust or cold galv sealant to each hole (e.g. CRC Soft Seal or similar).
- Install supplied nutserts with nutsert tool. Set firmly.
- Apply thread sealant to each Nutsert.
- Offer Sunvisor back to truck. Attach with 2 x M8 bolts as before. Tighten.
- Fix to truck using supplied cap-screw fasteners.
Note: This product is made in New Zealand.
AIRPLEX INDUSTRIES LIMITED
AUTOMOTIVE ACCESSORY MANUFACTURERS
21 SALEYARDS ROAD, OTAHUHU, AUCKLAND, NEW ZEALAND
P.O. BOX 11-286, ELLERSLIE, AUCKLAND, NEW ZEALAND
PHONE 64 (9) 276-9826 – FAX 64 (9) 276-9836
Email info@airplex.com,
www.airplex.com
Installation Guide – Part # SV117F
FUSO FV FS HD Euro Low Roof Cab Sunvisor
Tools required
- Drill – 3mm & 9mm drill bits
- Tec screws & bit (for temporary fastening)
- Alan key for 6mm machine screw
- Rivnut / Nutsert tool
- Marker pen
- CRC Soft Seal (or similar rust prevention)
INSTALLATION
- Hold the sunvisor to the front of the truck to identify the 2 innermost bolts above the windscreen that align with the 2 large sunvisor holes.
- Remove these 2 bolts from above the windscreen.
- Offer sunvisor to cab of truck again. Use M8 bolts supplied to temporarily fix sunvisor to cab using identified holes.
- Check alignment of sunvisor. Make sure it is level with cab.
- Working from the centre towards the outer ends, firmly hold sunvisor against the cab and temporarily fix to the cab using the tec screws or similar. Drill all holes.
- Remove sunvisor. On the truck, drill all new holes out to 9mm.
- Apply anti-rust or cold galv sealant to each hole (e.g. CRC Soft Seal or similar)
- Install supplied nutserts with nutsert tool. Set firmly.
- Apply thread sealant to each Nutsert.
- Offer Sunvisor back to truck. Attach with 2 x M8 bolts as before. Tighten.
- Fix to truck using supplied cap-screw fasteners.
Made in New Zealand
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>