Hisense ES-A22521A-1 B Smart TV User Manual
- June 13, 2024
- Hisense
Table of Contents
ES-A22521A-1 B Smart TV
Product Information
The product is a TV with the model number ES-A22521A-1 B. It
comes with a user manual and an embedded E-Manual. The TV is
equipped with various software functions that may change with
system upgrades. The product may appear different from the figures
and illustrations provided in the manual.
The TV comes with accessories, which may vary depending on the
model and country/region. Please refer to the actual accessory bag
for the included accessories.
It is important to read the safety instructions before
installing and operating the TV. The TV is compatible with some 3rd
party products, software, and services, but compatibility is not
guaranteed. The manufacturer is not liable for any damage or loss
caused by using incompatible devices or apps.
Recording and playback of content on this TV or any other device
may require permission from the owner of the copyright or other
related rights. It is the user’s responsibility to comply with
applicable copyright legislation and regulations.
The TV is designed for use in a home or office environment,
either on a table-top or wall-mounted. It should not be used in
rooms with high humidity or dust concentration to ensure optimal
performance. The warranty is valid only if the TV is used as
intended by the manufacturer.
Product Usage Instructions
-
Before operating the TV for the first time, read the user
manual carefully and ensure you fully understand its contents. -
Ensure to read and follow all safety instructions to avoid
dangerous situations and damage to the unit. -
Check the included accessories list to verify the accessories
that come with the TV. -
If needed, refer to the embedded E-Manual for additional
support. To access the E-Manual, go to Settings > Support >
E-Manual on the TV. -
For specific functions or features, use the search function in
the E-Manual to find the help you need. -
If you prefer using your mobile device, scan the provided QR
code to open the E-Manual on your mobile device and directly go to
the function page. -
Ensure to comply with applicable copyright legislation when
recording or playing back content on the TV or any other
device. -
Install the TV in a suitable location, such as a table-top or
wall-mounted, in a home or office environment with normal humidity
and dust levels. Avoid using it in rooms with high humidity or dust
concentration. -
Use the TV as intended by the manufacturer to ensure the
validity of the warranty.
Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time.
ES-A22521A-1 B
English Deutsch Español Italiano Português Français Nederlands
Read the manual carefully and ensure you have fully understood its contents
before operating this device for the first time.
English
Figures and illustrations in this manual are provided for reference only and
may differ from actual product appearance.
Parts of the software function changes with the system upgrade.
Find what you want
This TV is equipped with a user manual and embedded E-Manual (Settings >
Support > E-Manual).
E-Manual support functions
Search
Find the help you are looking for.
Try Now QR Code
Go directly to the function page and try it. Scan to open the E-Manual on your mobile device.
Contents
Installing the Stand or Wall mount bracket ……………………………………………………………1 TV Front
and Rear…………………………………………………………………………………………….3 Connection
………………………………………………………………………………………………………5 Remote Control
………………………………………………………………………………………………..7 Specifications
…………………………………………………………………………………………………10 Other
Information…………………………………………………………………………………………….12
Accessories List
The following accessories are included with TV:
User Manual × 1
Screw × 4
Base Stand × 2
AA or AAA Battery × 2
Remote Control × 1
Power Cord × 1
Warranty Card × 1
RCA jack to AV Cable × 1(65″)
NOTE
The accessories may be different from the list above due to different models,
countries / regions. Please refer to the actual accessory bag.
Important Notice
Paragraphs beginning with the symbol conditions for the following settings.
indicate important instructions, tips or
For your own safety and the optimal performance of your TV, ensure to read the safety instructions before performing any installation.
Compatibility with 3rd party products, software and services are not
guaranteed. We cannot be held liable for any damage or loss suffered whilst
operating, using or connecting to incompatible devices or apps.
The recording and playback of content on this or any other device may require
permission from the owner of the copyright or other such rights in that
content. It is your responsibility to ensure that your use of this or any
other device complies with applicable copyright legislation in your country.
Please refer to that legislation for more information on the relevant laws and
regulations involved or contact the owner of the rights of the content you
wish to record or playback.
Read these instructions Follow all instructions Heed all warnings Keep these
instructions All rights reserved.
Safety Instructions
To ensure safe and correct use of this product, always comply with the
following precautions to avoid dangerous situations and damage to your unit:
The lightning flash with arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
AC voltage: This symbol indicates that the rated voltage marked with the
symbol is AC voltage.
Class II product : This symbol indicates that it does not require a safety
connection of protective earthing (ground).
A
The intended use and ambient conditions for this TV
This TV is intended for the rendering of video and audio signals, on a table-
top or wallmounted, in a home or office environment. It must not be used in
rooms with a high level of humidity or dust concentration. The warranty is
only valid if used as intended by the manufacturer.
WARNING
High humidity and dust concentration may lead to current leaks in the device.
To reduce the risk of fire or electrical shock: – Do not expose this unit to
rain, moisture, dripping or splashing water, and do
not place objects filled with liquids, such as vases, cups, etc. on or over
the unit. – Do not touch the TV with wet hands. – Do not expose to direct air-
conditioning and keep candles or other naked flames away from the TV at all
times. If the TV is moved from a cold environment to a hot environment, leave
it switched off for at least an hour to avoid condensation. If used outside,
make sure it is protected from moisture. If you notice anything unusual,
immediately remove the power plug. In case of fire, use preferably a CO2 gas
or powder fire extinguisher. If such extinguishers are not accessible, try to
isolate the electrical supply before using a water fire extinguisher.
WARNING
Stability Hazard A television set may fall, causing serious personal injury or
death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as: – ALWAYS use
cabinets or stands or mounting methods recommended by the manufacturer of
the television set. – ALWAYS use furniture that can safely support the
television set. – ALWAYS ensure the television set is not overhanging the edge
of the supporting furniture. – ALWAYS educate children about the dangers of
climbing on furniture to reach the television
set or its controls. – ALWAYS route cords and cables connected to your
television so they cannot be tripped over,
pulled or grabbed. – NEVER place a television set in an unstable location. –
NEVER place the television set on tall furniture (for example, cupboards or
bookcases)
without anchoring both the furniture and television set to a suitable support.
– NEVER place the television set on cloth or other materials that may be
located between the
television set and supporting furniture. – NEVER place items that might tempt
children to climb, such as toys and remote controls, on
the top of the television or furniture on which the television is placed. If
your existing television set is being retained and relocated, the same
considerations as above should be applied.
B
Moving/Transportation
Power plug and power cable
Before moving this TV, disconnect all cables and move in the vertical position
only. Grasp the device on the upper and lower edges of the frame.
– Do not press or put stress on the front panel of the TV. It may take two or
more people to carry larger TVs.
If you have to briefly lay down the TV, place the unit with its entire front
surface lying flat on soft material.
The LED screen is made of glass and can break if is not handled properly.
Always wear rubber gloves to carry the unit. If the LED screen is damaged,
liquid crystal might leak out. In case of skin contact, immediately rinse
thoroughly with water.
Power Supply
Incorrect voltages can damage the TV. Only connect this unit to a power supply
with the correct voltage and frequency noted on the type plate, using the
supplied power cable.
The power plug must be easily accessible so that the device can be
disconnected at all time. The unit is live, even if in standby mode, as long
as the unit is connected to a power outlet.
It is recommended that this unit is placed on a dedicated circuit.
– Do not overload the power outlets by connect too many appliances to the same
outlet. Overloaded wall outlets, extension cords, etc. are dangerous and can
result in electric shock and fire.
After power off, don’t turn it on again in 5 seconds. Frequent switching power
supply in a short period of time can cause abnormal TV.
– Do not touch the power plug with wet hands.
– Do not place heavy objects on the power cable. Route the cable so that it is
not kinked or laid over sharp edges, walked on or exposed to chemicals. A
power cable with damaged insulation can cause electric shock and fire.
– Pull the power plug, NOT on the cable when disconnecting. The cable can
become damaged and cause a short circuit if pulled on.
– Do not place the power cable near a high temperature object.
– Do not move the TV with the power cable plugged into a socket.
– Do not use a damaged or loose power cable, or a damaged socket outlet.
– Do not use any power cords other than the one supplied with this unit.
– MAIN plug on the power cord is used as the disconnect device, the disconnect
device and socket-outlet shall be easily accessible.
Set-up
Check that the location is suitable to bear the load of the TV. Place on a
level, sturdy and horizontal base. Ensure that the unit does not hang over the
edge of the base when placed in or on furniture. If placed on a cart, use
caution when moving to avoid the unit from tipping over.
– Place the unit in a normal upright horizontal position. It must never be
operated vertically, lying flat or hanging overhead from the ceiling.
– Place the unit where it is not exposed to direct sunlight or other sources
of heat.
When mounting the TV on a wall, follow the instructions supplied with the
wallmount, make sure not to install the TV by
C
hanging the power and signal cables on Prevent small items from getting into the
the back of the TV.
interior of the device through the ventilation
slots. Such objects may cause short circuits,
Air ventilation and high
which may cause fire.
temperatures
If something should get inside the unit,
Install your TV only where there is proper ventilation, and ensure that there is at least
immediately unplug the power plug of the device and contact service support.
10 cm free space on the sides and 20 cm The LED screen
above the unit for air circulation. Excessive
heat and obstruction of ventilation could
Despite thorough care when manufacturing
lead to fire or early failure of some electric this display, it cannot be 100% guaranteed
components.
that no sub-pixel defects will occur due
– Do not block any ventilation openings with newspapers, tablecloths,
curtains, etc.
– Do not dry clothing etc. on top of the unit.
to technical reasons. These cannot be considered as a device defect in terms of the guarantee. They will not affect the performance and reliability of the TV.
– Take care not to touch the ventilation openings since they may become hot.
– Do not insert foreign objects into the TV through the vents.
To prevent “image burn”, avoid displaying still images for long periods of time, there is a possibility that a copy of the image may remain. If the aspect ratio is set to 4:3 for a long period of time, image burn may
The Stand
occur on the black areas. Image burn is not covered by the warranty.
– Do not use any stand other than the one supplied with this unit.
– Do not apply strong force or impact on the display panel.
– Do not modify or use the stand if it becomes warped of physically damaged.
– During setup, make sure that all the screws are securely tightened.
Avoid touching the LED screen or touching it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
– Ensure that the TV does not suffer any impact during the attachment of the
stand.
– Ensure that children do not climb onto the stand.
– Attach or remove the stand with at least two people.
Radio waves
– Do not use the TV in any medical institutions or locations with medical
equipment. Radio waves may interfere with medical equipment and cause
malfunction.
20cm
– Do not use the TV near any automatic
control equipment such as automatic
10cm
10cm
10cm
doors or fire alarms. Radio waves
may interfere with automatic control
equipment and cause malfunction.
If you have a cardiac pacemaker, keep a distance of at least 22 cm from the TV. Radio waves may interfere with the operation of a pacemaker.
D
Built-in wireless LAN
Thunder Storms
– Do not connect to wireless networks that you do not have the usage rights
for. Data transmitted and received over radio waves may be intercepted and
monitored.
The built-in wireless LAN uses 2.4 GHz and 5 GHz frequency band. To avoid
malfunctions or slow response caused by radio wave interference, keep the TV
away from devices such as other wireless LAN devices, microwaves, mobile
phones, and other devices that use 2.4 GHz and 5 GHz signal.
Warning about off-gassing
Pull out the power plug and all connected antenna cables from the TV during a
thunderstorm. Overvoltage caused by lightning strikes can damage the TV via
the antenna system, as well as the wall socket.
Long periods of absence
As long as the power plug is connected to a live socket outlet, the TV will
consume power even in standby mode. The power plug and all connected antenna
cables should be disconnected out during long periods of absence.
New furniture, carpet, paint, building
materials and electronics can release
Cleaning and care
chemicals into the air through evaporation.
After you set your TV up and turn it on for the first time, you may notice a slight smell CAUTION: within a couple of hours. This is because Unplug the power cord prior to cleaning some components of TV are heating up the TV.
for the first time. The materials that we use Clean the TV, the screen, and the remote
fully meet the environmental requirements control with a soft, moist, clean and
and regulations. Your TV is working just colour-natural cloth only. Do not use any
fine and the fumes from the off-gassing chemicals.
will diminish eventually.
– Do not subject the surfaces to insect
repellent, solvent, thinner or other
Supervision
volatile substances. This may degrade the surface quality.
– Do not let children play unsupervised close to the TV. It could tip over, be
pushed off or pulled down from the stand surface and injure someone.
– Do not allow a switched-on TV to run unattended.
– Do not spray water or other liquids directly on the TV. Liquid inside the TV
could lead to product failure.
– The surface of the display panel is treated and may be easily damaged. Take
care not to scratch it with
Volume
fingernails or other hard objects. – Also wipe the power plug with a dry
Loud music and noises can lead to
cloth at regular intervals.
irreversible damage to your ears. Avoid extreme volume, especially over long
Service/Repair
periods and when using headphones.
Never remove the cover/back of the TV;
If you hear a drumming noise in your ears, there are no user serviceable parts inside.
turn down the volume or temporarily stop Refer all service to qualified service
using headphones.
personnel.
E
Packaging Important Safety- IeRnqesupiltvaraculeencotnttilyyopwen.itsh the same or
Keep the anti-moisture materials and plastic bags out of reach of children.
Plastic bags can cause suffocation and the anti-moisture material is harmful
if swallowed. If swallowed by mistake, force the patient to
– Do not mix old and new batteries. – Do not mix different battery types. – Do no use rechargeable batteries. – Do not burn or break up batteries.
vomit and visit the nearest hospital.
– Be sure to dispose of batteries correctly.
Modification
– Do not expose batteries to excessive heat such as sunshine, fire or the like.
Do not attempt to modify this product in any way. Unauthorised modification
Outdoor Antenna Grounding
could void the warranty of this unit, cause If an outdoor antenna used, be sure the
electric shock and fires.
antenna system is protected against
voltage surges and built-up static charges.
Remote Control batteries – Incorrect installation may cause battery Disposal
leakage, corrosion and explosion.
Refer to the recycling section of this manual.
F
Installing the Stand or Wall mount bracket
CAUTION
Be sure to disconnect the AC power cord before installing a stand or wall
mount brackets.
The display on your TV is fragile. Make sure the TV screen is not scratched or
damaged by hard objects or from pressure. After the installation is completed,
make sure the TV is steady on a table or firmly attached to a wall mount,
before removing all protective film, if any. Installing the stand Follow the
illustrations and textual instructions below to complete the installation
steps: 1. Carefully place your TV face-down on a soft, flat surface to prevent
damage to the TV or scratching to the screen.
2. Take out the 2 stands from the accessory bag and then insert the stands
into the bottom slots of the TV.
3. Secure the stands to the TV with the 4 screws in accessory tightly.
43″
50″/55″
Base Stand
Base Stand Screws: M4×16
Base Stand
Base Stand Screws: M5×12
65″ Note: If your table is long enough to place the TV on top of, then insert
the base stands into the screw holes A’ that are shown in the illustration. If your table is NOT long enough, then insert the base stand into the screw holesB’ that are shown in the illustration. Note that
these two installation methods types cannot be mixed.
A Base Stand
A Base Stand Screws: M5×12
1
B Base Stand
B
Screws: M5×12
Base Stand
Installing the wall mount bracket Before mounting the TV, remove the TV stand
if you have already attached it, and make sure the wall mount bracket supports
the weight of your TV.
CAUTION
When mounting the TV on a wall, follow instructions provided with the wall
mount bracket. If it is not correctly mounted, the TV may fall and cause
property damage or personal injury.
Place spacers between the TV and bracket. Standard dimensions are shown below.
Wall mount hole pattern (mm) Wall mount screw size
200 × 300 (43″/50″/55″) 400 × 300 (65″)
M6
8.0 -10.0 mm (43″/50″/55″) 9.5 – 11.5 mm (65″)
Wall Mount Bracket
Rear cover of the TV
Wall Mount Screw Wall Mount Spacer
We do not recommend hanging the TV on a slanted wall, and
when wall mounting make sure your television remains parallel to
the wall and does not lean forward.
TV screen
Vertical surface
NOTES
The diameter and length of the screws differ depending on the wall mount bracket model.
Wall mount bracket is optional. Your TV may not have wall mount bracket. Please refer to the actual accessories.
2
TV Front and Rear
Power indicator / Power button(Standby/Source)
Item Power indicator
Description The light is white in standby mode.
Power button
Press the button to turn the TV on. Press it again to bring up the
control menu and move the focus between different inputs. Long
Standby / Source press the button to make a selection.
NOTES
For 43″/50″, ANT2 Jack supports power supply for satellite antenna (13/18V,
420mA max.)
For 55″/65″, ANT2 Jack supports power supply for satellite antenna (13/18V,
0.5A max.)
Check the jacks for position and type before making any connections. Loose
connections can result in image or colour problems. Make sure that all
connections are tight and secure.
Not all A/V devices have the ability to connect to a TV, please refer to the
user’s manual of your A/V device for compatibility and connections procedure.
Before connecting external equipment, remove the mains plug from the wall
socket. Otherwise, it may cause electric shock.
Powering on the TV requires several seconds to load programmes. Do not rapidly
turn the TV off as it may cause the TV work abnormally.
The Picture is Only for Reference.
3
65″ 43″/50″/55″
43″/50″ 55″
HDMI 1(eARC) 4K@60Hz
AC INPUT 43″/50″/55″
65″
AC INPUT
LAN
DIGITAL AUDIO OUT
420mA
4
Connection
Terminals
ANT 1
or
DVB-T/T2/C
ANT 2 DVB-S/S2
ANT OUT
DIGITAL AUDIO OUT
HDMI (eARC)
HDMI
Audio Amplifier/Speaker
Audio Amplifier/Speaker
HDMI
DVD/Blu-Ray/AV receiver/ Set-top Box
HDMI
43″/50″/55″
HEADPHONE
NOTE Excessive sound pressure from earphones and headphones can cause hearing
loss.
Yellow(Video) White(L) Red(R)
VCR/DVD Player/ Recorder/Set-top box/
Satellite Receiver/ Video Camera
A/V OUT
Video L
R
65″
AV IN
Red(R) (not included)
White(L) (not included) Yellow(Video)
(not included)
VCR/DVD Player/ Recorder/Set-top box/
Satellite Receiver/ Video Camera
A/V OUT
Video L
R
CAM CARD
NOTE
Do not repeatedly insert or remove the Common Access Module as this may damage
the interface and cause a malfunction.
You must obtain a CI+ module and card from the service provider of the
channels you want to watch.
CI+ is not supported in some countries and regions.
USB DC 5V 0.5A(MAX)
NOTE
Exceeding a total current consumption may result in damage. The USB 1.1 and
USB 2.0 devices maximum current consumption are 500mA. The USB 3.0 device
maximum current consumption is 1A (only for some models).
For individual non-standard high-capacity mobile hard disk, if its impulse
current is greater than or equal 1A, it may cause TV-rebooting or self-
locking. So the TV does not support it.
5
LAN (Wired setup)
Connect your TV to your network by connecting the LAN port on the back of your
TV to an external modem or router using a LAN (Ethernet/Cat 5) cable. See the
illustration below.
· It is recommended to use a modem or router that supports Dynamic Host
Configuration Protocol (DHCP). Modems and routers that support DHCP
automatically provide the IP address, subnet mask, gateway, and DNS, so you
don’t have to enter them manually. Most home networks already have DHCP.
TV JACK
IP Sharer (Router) (with DHCP server)
External Modem (ADSL / VDSL / Cable TV)
LAN Cable
LAN Cable
Modem Cable
Wireless setup
To connect your TV to your network wirelessly, you need a wireless router or
modem. See the illustration below. · The built-in Wireless LAN Adapter
supports the IEEE 802.11a/b/g/n/ac
communication protocols. It is recommended to use IEEE 802.11ac router. Low
transfer rates for b/g may have the influence on the quality of streamed
videos and other media.
Wireless router with DHCP
Wireless LAN Adapter built-in TV set
LAN Cable
NOTES
You must use the built-in Wireless LAN Adapter to use a wireless network
because the set doesn’t support external USB network adapters.
If the wireless router supports DHCP, your TV can connect more easily to the
wireless network.
If you apply a security system other than the systems listed below, it will
not work with the TV.
Security system: WPA, WEP, WPA2.
In order to guarantee smooth network, the distance between router and TV
should be less than 10 metres.
6
Remote Control
NOTE: The included remote control will vary depending on model,
countries/regions. Check information according to the actual remote control in
the accessory bag.
7
Buttons of remote control
BUTTON
DESCRIPTION
Power on/ Standby
INPUT Number button / Four colour buttons / GUIDE CH.LIST
/ / / OK
Select input sources Select a channel or input numbers Special function buttons Display the Electronic Program Guide (DTV mode) Display the Channel List on the screen Playpad keys Press to enter Menu D-pad (up/down/left/right navigation buttons) Confirmation button Under the Menu or App, return to the previous place Display the Home screen
VOL
Volume (up/down)
CH
Channel (up/down)
Mute and restore sound
EXIT
Exit the menu or exit the application
Activate the microphone
INFO
Display the current program information
SUBTITLE
Activate or deactivate the subtitle mode
MEDIA
Enter the MEDIA
/
Fast access to all applications
APP
Quick access buttons to APP
TEXT/TXT
Turn on/off the teletext function
BROWSER
Enter into BROWSER
Custom button to launch input or apps quickly
Enter Channels / input numbers and special function buttons(Red/Green/Yellow/Blue)
NOTE: Buttons listed here are for reference only. Actual remote control may vary depending on model, country/region.
8
Installing Batteries in the Remote Control
1. Slide the back cover to open the battery compartment of the remote
control.
2. Insert two AA or AAA size batteries. Make sure to match the (+) and ( – )
ends of the batteries with the (+) and ( – ) ends indicated in the battery
compartment.
3. Close the battery compartment with the cover.
NOTE Product image is only for reference, actual product may vary in
appearance. Dispose of your batteries in a designated disposal area.
Do not mix battery types or combine used batteries with new ones.
Remove depleted batteries immediately to prevent battery acid from leaking
into the battery compartment. If you do not intend to use the remote control
for a long time, remove the batteries. Leaving a battery in an extremely high
temperature surrounding environment that can result in an explosion or the
leakage of flammable liquid or gas. Battery chemicals can cause a rash. If the
batteries leak, clean the battery compartment with a cloth. If chemicals touch
your skin, wash immediately. Risk of fire or explosion if the battery is
replaced by an incorrect type. Disposal of a battery into fire or a hot oven,
or mechanically crushing or cutting of a battery, that can result in an
explosion. A battery subjected to extremely low air pressure that may result
in an explosion or the leakage of flammable liquid or gas.
Pairing the Remote Control (only for Bluetooth remote control) Pair the remote
to the TV after you power it on. Keep the remote control within 3 metres from
the TV. Press any button (except power and mic button) to pair.
NOTE In special cases, press and hold [ ] button to pair.
If an unknown error occurred with the remote, then it could have been caused
by interference. Try to remove what’s causing the interference and pair it
again.
If an unknown error occurred in the remote control while the battery power is
normal, you can take out the batteries, press any key for 1~2 seconds, and
insert them back. Then the remote control will work normally. The remote
cannot be paired to the TV while the TV is in standby mode.
Remote Control Operation Range
1. The remote control can work at a distance of up to 8 meters in front of
the TV set.
2. The remote control angle: taking the remote sensor as an apex, 6 meters
away, its controlled horizontal angle is within ±30°, while the vertical angle
is within ±15°.
3. The operating distance may vary depending on the brightness of the room.
Disposal of this unit
Product should not be damaged, dismantled or thrown in municipal waste. It
should be packed and handed over to authorised re-cycler.
9
Specifications
Features, appearance and specifications are subject to change without notice.
Item
43″
50″
Dimension (W × H × D)
Without Stand
37.9 × 22.0 × 2.9 inches 963 × 560 × 74 mm
44.0 × 25.4 × 2.9 inches 1117 × 646 × 74 mm
With Stand
37.9 × 24.1 × 8.8 inches 44.0 × 27.7 × 10.8 inches 963 × 611 × 223 mm 1117 × 703 × 274 mm
Weight
Without Stand 16.3 lbs (7.4 kg) With Stand 17.2 lbs (7.8 kg)
Active Screen Size (Diagonal) 108 cm
Screen resolution
3840 × 2160
Audio power
7W + 7W
Operating mode power density 0.020 Watts/cm²
Power consumption when turned off N.A.
Power consumption in standby mode 0.5 W
21.6 lbs (9.8 kg) 22.0 lbs (10.0 kg) 126 cm 3840 × 2160 8W + 8W 0.018 Watts/cm² N.A. 0.5 W
Item
55″
65″
Dimension (W × H × D)
Without Stand
48.5 × 28.0 × 2.9 inches (1232 × 711 × 74 mm)
57.2 × 32.8 × 2.9 inches (1452 × 834 × 74 mm)
With Stand
48.5 × 30.2 × 10.8 inches 57.2 × 35.3 × 11.8 inches (1232 × 768 × 274 mm) (1452 × 896 × 300 mm)
Weight
Without Stand 24.9 lbs (11.3 kg) With Stand 25.4 lbs (11.5 kg)
36.4 lbs (16.5 kg) 36.8 lbs (16.7kg)
Active Screen Size (Diagonal) 139 cm
164 cm
Screen resolution
3840 × 2160
3840 × 2160
Audio power
8W + 8W
10W + 10W
Operating mode power density 0.016 Watts/cm²
0.015 Watts/cm²
Power consumption when turned off N.A.
N.A.
Power consumption in standby mode 0.5 W
0.5 W
Power consumption
Please refer to the rating label.
Power supply
Please refer to the rating label.
Receiving systems
Analog Digital
PAL-D/K, B/G, I, SECAM-D/K, B/G DVB-T/T2, DVB-C, DVB-S/S2
10
Wireless LAN Module specifications
Frequency Range
2.4-2.4835GHz 5.15-5.85GHz
Output Power (Max.)
2.4-2.4835GHz 17dBm 5.15-5.25GHz 14dBm 5.25-5.35GHz(DFS Band) 14dBm 5.49-5.71GHz(DFS/TPC Band) 14dBm 5.725-5.85GHz(for Non EU) 14dBm
Bluetooth Module specifications
Frequency Range 2.4-2.4835GHz
Output Power (Max.)
2.4-2.4835GHz, Class1, 6dBm
Environmental conditions
Temperature: 41°F – 95°F (5°C – 35°C) Humidity: 20% – 80% RH Atmospheric pressure: 86 kPa – 106 kPa
HDMI Input
RGB / 60Hz (640×480, 800×600, 1024×768) YUV / 60Hz (480i, 480p, 720p, 1080i,
1080p) YUV / 50Hz (576i, 576p, 720p, 1080i, 1080p) 3840×2160 / 24Hz, 3840×2160
/ 25Hz, 3840×2160 / 30Hz, 3840×2160 / 50Hz,
3840×2160 / 60Hz
11
Other Information
Recycling/Licenses
WEEE (Waste Electronic Electric Equipment) European Directive 2012/19/EU
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
Batteries
In accordance with the Battery Directive, used batteries should not be
disposed of in the domestic waste. Dispose your batteries in the
collection containers specific for this purpose in retail stores.
ROHS (Restriction of Hazardous Substance) European Directive 2011/65/EU
This European directive limits the use of dangerous and hazardous substances
which are difficult to recycle. This allows recycling easily the EEE and
contributes to the safeguard of the environment. Substances included in this
product match to the RoHS directive.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing Administrator,
Inc. in the United States and other countries.
Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered
trademarks of Dolby Laboratories Licensing Corporation. Manufactured under
license from Dolby Laboratories. Confidential unpublished works. Copyright ©
20122022 Dolby Laboratories. All rights reserved.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS, DTS:X, and the DTS:X logo are registered
trademarks or trademarks of DTS, Inc. in the United States and other
countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.
12
SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Hisense Visual Technology Co.,
Ltd. declares that the radio equipment type [ERF2J36H / ERF2K36H / ERF2L36H /
ERF2M36H / ERF2N36H / ERF2O36H / ERF2P36H / ERF3C96H / ERF2F36H / ERF3N80H /
ERF2S36H / ERF2V36H / 43E7KQ / 43E77KQ / 43E78KQ / 43E79KQ / 43E7KQTUK /
43E77KQTUK / 43E78KQTUK / 50E7KQ / 50E77KQ / 50E78KQ / 50E79KQ / 50E7KQTUK /
50E77KQTUK / 50E78KQTUK / 55E7KQ / 55E77KQ / 55E78KQ / 55E79KQ / 55E7KQTUK /
55E77KQTUK / 55E78KQTUK / 65E7KQ / 65E77KQ / 65E78KQ / 65E79KQ / 65E7KQTUK /
65E77KQTUK / 65E78KQTUK] is in compliance with Directive 2014/53/EU. The full
text of the EU declaration of conformity is available at the following
internet address: https://global.hisense.com/support/certificate-download/.
For Great Britain: SIMPLIFIED UK DECLARATION OF CONFORMITY
Hereby, Hisense Visual Technology Co., Ltd. declares that the radio equipment
type [ERF2J36H / ERF2K36H / ERF2L36H / ERF2M36H / ERF2N36H / ERF2O36H /
ERF2P36H / ERF3C96H / ERF2F36H / ERF3N80H / ERF2S36H / ERF2V36H / 43E7KQ /
43E77KQ / 43E78KQ / 43E79KQ / 43E7KQTUK / 43E77KQTUK / 43E78KQTUK / 50E7KQ /
50E77KQ / 50E78KQ / 50E79KQ / 50E7KQTUK / 50E77KQTUK / 50E78KQTUK / 55E7KQ /
55E77KQ / 55E78KQ / 55E79KQ / 55E7KQTUK / 55E77KQTUK / 55E78KQTUK / 65E7KQ /
65E77KQ / 65E78KQ / 65E79KQ / 65E7KQTUK / 65E77KQTUK / 65E78KQTUK] is in
compliance with Radio Equipment Regulations 2017. The full text of the UK
declaration of conformity is available at the following internet address:
https://global.hisense.com/support/certificatedownload/.
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE
REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC
VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO
PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
13
EPREL Registration Information
Model identifier Eprel registration number
43E7KQ
1448882
43E77KQ
1448887
43E78KQ
1448895
43E79KQ
1448898
43E7KQTUK 1448904
43E77KQTUK 1448910
43E78KQTUK 1448975
50E7KQ
1449676
50E77KQ
1449681
50E78KQ
1449683
50E79KQ
1449685
50E7KQTUK 1449686
50E77KQTUK 1449687
50E78KQTUK 1449688
Model identifier Eprel registration number
55E7KQ
1460914
55E77KQ
1460933
55E78KQ
1460938
55E79KQ
1460940
55E7KQTUK 1460942
55E77KQTUK 1460944
55E78KQTUK 1460945
65E7KQ
1452080
65E77KQ
1459494
65E78KQ
1459496
65E79KQ
1459498
65E7KQTUK 1459469
65E77KQTUK 1459499
65E78KQTUK 1459501
14