PHILIPS SP571P-X FlatLay LED Tube Light Instructions
- June 13, 2024
- Philips
Table of Contents
PHILIPS SP571P-X FlatLay LED Tube Light Instructions
1 Suspension Cable adjustment
IMPORTANT: Do not force cable into adjuster. To insert cable into adjuster, follow the steps below.
- CUT If required, cut cables ends cleanly prior to inserting into adjuster.
- INSERT Carefully insert cable from top end. if cable does not insert easily or becomes jammed, use the release tool to remove tool to remove cable. Trim cable ends again and repeat process. DO NOT BEND OR LOOP CABLE BELOW BOTTOM OF ADJUSTER.
- TEST Once cable is inserted, apply a 12Kg point load to each mount bracket to ensure all connections are secure.
2 Suspension Cable fixing location (recommended)
3 Luminaire mounting
- A) Fix the suspenders at the recommended distance. Insert the cable at marked hole and slide the suspension along the groove.
- B) Tight the suspension cable stoppers on both sides after positioning the suspension cables.
- C) Remove the filament tape. Run the transparent cable along with suspension cable and fix at 2 locations with the help of cable holder. Do not keep transparent cable loose.
- D) Ensure fixture is level end to end. Support fixture from below and use adjuster release tool to make final height adjustments. Check level by spirit level in both the planes, Horizontal and Vertical.
4 Joining of Luminaires – Continuous mounting
- Fix the joining bracket at one end of fixed luminaire with M4x10 screws (x4).
- Next suspended luminaire is connected in one movement as shown below and fix with M4x10 screws (x4).
- Fixing of end cap with first and end luminaire.
Supply Connection ( Place Driver plate assembly behind the ceiling after
connection)
Connect the transparent cable from luminaire with 3-Pole connector on driver
output side, LED+, LED- (DC power supply), and earth connection. Connect mains
supply cable (AC power) with the 3-Pole connector on the driver plate.(L-N-E)
Wire Stripping
For MAINS
Wire size 0.5-1.5mm2
7-8mm
E L N
40mm
Connection – Luminaire to Driver (DC Power)
Red wire for LED+ Green wire for Earthing Black wire for LED-
From Driver
LED+
LED-
From Luminaire
Transparent Cable
Insert 3 wires LED+, LED- & E(earth) in 3 Pole connector.
DA+ DA-
Wire Stripping
For DALI
Wire size 0.5-1.5mm2
7-8mm 40mm
Mains Connections for PSU series
From Driver
Mains
Mains Connections for PSD series
From Driver
Mains
From Driver
DA-
DA+
Insert 3 wires L, N, & E in 3 Pole connector.
NOTE: DO NOT OPEN ANY OTHER SCREWS (open only Connector screws)
Insert 3 wires L, N, & E in Insert 2 wires for Dali+ & Dali-
3 Pole connector.
in 2 Pole connector.
Caution
1. “The light source of this luminaire is not replaceable. when the light
source reaches its end of life the whole luminaire shall be replaced”.
2. Do not stare at the operating light source.
3. If the external flexible cable or cord of this luminaire is damaged, it
shall be exclusively replaced by the manufacturer or his service agent or a
similar qualified person in order to avoid a hazard.
Warning
1. Choosing an appropriate fixing to suit the mounting surface is the
responsibility of the installer.
2. The luminaire shall be installed by a qualified electrician and wired in
accordance with the latest IEE electrical regulations or the national
requirements.
3. The luminaire should be earthened properly for Safety and Performance.
4. Do not switch on before complete installation.
Maintenance
Ensure power supply is switched off before attempting any maintenance work.
The luminaire must be used within the applicable product specifications,
installation instruction and environmental conditions for storage & operations
according to application guidelines provided by Signify for product warranty
to be valid.
Signify Innovations India Limited formerly known as Philips Lighting India
Limited PS ARCADIA CENTRAL, 3A, 3rd floor, 4A, Abanindranath Thakur Sarani
(Camac Street), Kolkata 700 017
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>