SHREDLIGHTS 2A7H2-SL-300 PLUS E RIDERZ User Guide

SHREDLIGHTS 2A7H2-SL-300 PLUS E RIDERZ

Product Information

This product is designed to operate within the guidelines set forth by the Federal Communications Commission (FCC) in the United States. It complies with part 15 of the FCC Rules, which ensures that the device does not cause harmful interference and can accept any interference received.

• It is important to note that any changes or modifications made to the equipment without approval from the responsible party may void the user’s authority to operate the device.
• The product also meets the FCC radiation exposure requirement for uncontrolled environments.

Product Usage Instructions

To ensure proper operation and compliance with FCC regulations, please follow these guidelines:

1. Reorient or relocate the receiving antenna if you experience interference.
2. Increase the separation between the equipment and the receiver if interference persists.
3. Connect the equipment into an outlet on a different circuit than the one to which the receiver is connected.
4. If you require assistance, consult the dealer or an experienced radio/TV technician.

WARNING

1. Riding at night can be more dangerous than during the day. Use extra caution and ride within your limits. Always wear a helmet and other protective gear to help avoid serious injury or death.
2. Avoid using this light in full power when riding towards oncoming cars and/or pedestrians. Use caution when operating at full power to avoid temporarily blinding yourself or others.

Description

• Slide the bottom of the light into any S-LOCK mount until the clip ‘clicks’ into place. Ensure it’s secure before riding.
• To remove, press down on the front lever to disengage S-LOCK, then slide the light away from the mount.

Specification

Light Specs

SL-300+

SL-R1+

How to Pair Lights into Groups Without the App

App is recommended for first pairing out of the box

1. Enable Pairing Mode
   Light will flash at 10%brightness when pairing mode is enabled.

2. Pair 2 Lights to Create a Group
   Both lights will turn on to indicate successful pairing.
   Group 1
   Lights 1 & 2 can now be controlled together as Group 1.

3. Add Lights to a Group
   All 3 lights will turn on indicating Light 3 is paired to Group 1. Repeat this process to add lights to any group.

How to Remove Lights from a Group

1. Enable pairing mode on the light you want to remove
2. Press and hold the side button of a different light in the group

Control Full Groups With One Button

• Use any light in the group to turn the group on/off (hold 1 s) and change group light modes (press)
• Use the app to customize group light modes and check the battery status of lights and groups
• Lights remained paired to group after dying and being recharged

Bluetooth Control
Bluetooth is always on and ready to communicate with the app or other lights in the group.

Fcc Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure requirement set forth for an uncontrolled environment.

Download the App for Faster Setup & Full Control over Lights and Groups.

www.SHREDLIGHTS.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>