Lindr REV00 200L External Soda Water Maker Instruction Manual

CZECH UP YOUR BEER
COLLING AND DISPENSING SYSTEMS
INSTRUCTION MANUAL
Number 063-2023
REV00 Valid 2023-09-01

REV00 200L External Soda Water Maker

EXTERNAL SODA WATER MAKER 200L

IMPORTANT
This manual contains instructions for installation, use and operation of the appliance.
This manual is an integral part of the device. It must be stored in the vicinity of the device for the entirety of its service life and must be made available to the user any time the device is installed, moved, used or maintained. Read this manual carefully before  installing and using the device. It contains important information necessary to ensure that all operations are done properly and safely.
Due to the continuous improvement of the products, the pictures are located in the manual illustrative only and may differ from the purchased goods.
This manual is a translation of the original Czech manual.
LINDR.CZ s.r.o.
Sadová 132
503 15 Nechanice, Czech Republic
mobile: + 420 775 715 494
tel.:+420 495 447 239
e-mail: info@lindr.cz
web: www.lindr.cz,www.lindr.eu

SYMBOLS AND MARKINGS USED IN THE MANUAL:

WARNING:
Not following instructions may cause injury or damage the device.
DANGER:
Risk of injury by electrical current.
NOTE:
This symbol indicates information and recommendations for the user.

INTRODUCTION:

Thank you for purchasing this LINDR product.

DESCRIPTION OF THE DEVICE:

Soda Water Makers:
Soda Water Maker are the professional device designed for producing chilled soda water by mixing H2O and CO2.
This practical device can be used restaurants, production facilities and more.
The devices are not intended for filling barrels.

MACHINE PLATE:

GENERAL INSTRUCTIONS, MEASURES AND SAFETY INSTRUCTIONS:

When using the device, follow basic safety instructions stated by the manufacturer. The cooling device is designed for flow-through cooling of beverages. Any other use is considered impermissible and therefore dangerous.
The supplier is not liable for damage caused by incorrect use.
DO NOT USE THE DEVICE FOR PURPOSES OTHER THAN THOSE STATED BY THE MANUFACTURER!
The devices meet safety protection IP21.
General safety principles. Observe the following safety instructions.
The supplier is not liable for damage caused by activities carried out on this device without observing the following instructions!
WARNING: Children aged 15 or more and persons with reduced physical, sensory or mental capabilities or insufficient experience and knowledge may only use the device when supervised or instructed in safe use of the appliance and familiarised with potential dangers.
WARNING: Children must not be allowed to play with the appliance. Store all packaging material out of reach of children (comes with a plastic bag – suffocation hazard).
WARNING: Cleaning and maintenance of the appliance on the part of the user must not be done by unsupervised children.
WARNING: Before connecting to main electrical supply, check that the voltage and frequency in the mains corresponds to the data stated on the device.
WARNING: Always make sure that the socket you intend to plug the cooler into meets the specifications on the machine plate (voltage, frequency, input power).
WARNING: Before performing operations on the device such as cleaning or maintenance, ALWAYS disconnect the device from power supply: turn off the device with the main button and unplug the appliance from the socket.
WARNING: Never place tools or other objectinto the fan.
WARNING: Never touch electrical components with wet or damp hands.
WARNING: Always make sure the power socket you intend to plug the cooler into is ac- cessible, so that the appliance can be immedi- ately unplugged in case of emergency.
WARNING: When unplugging the device from the socket, grab the plug and pull it out. Do not under any circumstances pull at the cable; risk of damage.
WARNING: To turn the device off completely, unplug the appliance from the power socket.
WARNING: In the event the electrical wiring of the product becomes damaged, summon a trained service technician. Do not under any circumstances repair the device yourself.
WARNING: Do not place objects that could prevent air circulation on top of the cooler.

INSTALLATION AND PLACEMENT:

Place the cooler onto a stable, level surface (maximum permitted inclination: 2 degrees).
The appliance requires unobstructed air circulation.

• Ensure sufficient supply of fresh air.
• The device must not be placed in an enclosed space.
• The device must not be placed in the vicinity of heat sources or exposed to direct sunlight.

Minimum distance of vents from an obstacle that would limit air circulation must be 200 mm. Minimum distance for sections with no air vents is 70 mm. Ideally, use the device in a cool and well-ventilated room. The device is designed for use at ambient temperature of at least 16 °C and at most 32 °C.
WARNING: The device MUST NOT be used or stored at ambient temperature lower than 0 °C. The device is designed for use in a normal environment, always under a roof, protected from rain or sunlight. Climate class N.
DANGER: Protect the cooler and electrical connection from rain and spraying water!
WARNING: Do not under any circumstances lay the cooler on its side, not even during transport.
NOTE: In order for the device to work correctly and at maximum output, it is important to not cover up any of the device’s vents and ensure sufficient air circulation.

ELECTRICAL CONNECTION:

Connect the device to a power socket in accordance with specifications on the machine plate of the device. Electrical wiring is subject to local regulations. If the power leads (cables) are damaged, they must be replaced by the manufacturer, their service technician or a similarly qualified person to prevent risk of hazardous situations.
DANGER: Do not use or turn on the device if the power lead cable is damaged!

TESTING:

The product is delivered ready for immediate use.

WARRANTY:

The device comes with a warranty in accordance with general legal regulations of the Czech Republic or in accordance with the trade agreement. During the validity period of the warranty, we will remove any defects on the product free of charge, provided these defects were not caused by excess wear, improper handling, incorrect storage or by using the product in a way that is counter to the instruction manual or the product’s design as defined by the manufacturer. Materials replaced during the validity period of the warranty are our property. The legitimacy of the warranty claim is always decided by an authorised service centre. Warranty provided by a retailer outside of the territory of the Czech Republic is governed by the agreement between the retailer and the buyer in  heir mutual relationship; this agreement is not directly linked to the manufacturer. The agreement does not give the buyer the right to submit warranty claims to the manufacturer. Transport expenses or other costs are not covered by the warranty.
ATTENTION:
Electrical devices and appliances must be checked/inspected at a time stipulated by valid legislation of the country the device is operated in. Inspection of wiring may only be done by a person with valid authorisation for this activity. Service work, provision of spare parts and inspection is done by the manufacturer or an authorised service centre.

DEVICE DESCRIPTION (see Fig. 9.):

1. Inlet CO2 (Ø 8mm)
2. Inlet water (Ø 12,7mm)
3. Outlet SODA (Ø 9,5mm)
4. Main switch
5. Power socket
6. Power cable

RECOMMENDED ACCESSORIES:

1. Aqua Stop
2. Speed fitting JG F3/4 x 12,7mm
3. Holder
4. Pressure reducer for water
5. Speed fitting JG F1-2 x 12,7mm (2x)
6. Speed fitting JG 9,5 x 12,7mm (4x)
7. Speed fitting JG Y 12,7×12,7×12,7mm (2x)
8. Water Filter (2x)

NOTE: The recommended accessories are not included. The supplier is not liable for damages caused by not using this recommended accessory.
WARNING: For the correct production of soda water, a cooling device with an adequate capacity is necessary!

HOW TO WORK WITH SPEED FITTINGS (see Fig. 11.):

11.1 Speed Fitting Installation :
Grasp the speed fitting and insert the hose all the way inside the speed fitting body (ca. 20 mm). The end of the hose must be straight so that it plugs fully into the coupling. If the hose will not go in, moisten the end of the hose.
11.2 Speed Fitting Removal:
Hold the grey ring tight against the body of the speed fitting and pull out the hose.
WARNING: If you do not hold the grey ring but pull at the hose, the speed fitting will cut even deeper into the hose.
WARNING: Hoses must not be pressurised during removal.

CONNECTION AND PRESSURISATION (see Fig. 12.):

1. Main water connection 1/2‘‘ (drinking water)
2. Aqua Stop
3. Speed fitting JG F3/4 x 12,7mm
4. Speed fitting JG F1-2 x 12,7mm (2x)
5. Pressure reducer for water
6. Holder
7. Speed fitting JG Y 12,7×12,7×12,7mm (2x)
8. Water Filter (2x)
9. Speed fitting JG 9,5 x 12,7mm (4x)
10. Pressure reducer CO2
11. CO2 bottle
12. Soda maker
13. Cooler

The minimum flow rate of the inlet water must be 5 l/min.
Inlet water temperature 10 – 30 °C.

TABLE OF MALFUNCTIONS:

The soda water does
not flow.| Pressure at the inlet has exceeded 3.0 bar.
No water supply to the water tap.
Inlet of pressure of CO2 is not open.
Water filter blocked.
The pump runs for more than 240 seconds at a time
(enters fault mode).| Reduce the pressure on the water valve min. to 2.5 Bar.-max 3.0 Bar.
Open the valve on the water tap.
Open and check the inlet pressure CO2 on the cylinder and adjust the pressure of CO2 min.to 3.5 Bar – max. 4.5 Bar.
Check or replace the water filter.
The device must be restarted by disconnecting from the power socket.
The fittings do not seal
properly.| Poorly inserted tube.
Scratches on the hose.| Pull out the tube, check to see if there are not any sharp
edges, possibly shorten with knife.
Pull out and shorten for about 2 cm.

NOTE: If the defect persists even after the above steps are taken, contact a service centre.
Do not forget to specify the following:

• type of defect
• product type
• production year
• product‘s serial number (found on the machine plate)

Ordering Components:
ALWAYS USE ORIGINAL COMPONENTS. The manufacturer or supplier bear no responsibility for non-original components or components not recommended by the manufacturer.

SPARE PARTS:

When ordering spare parts, always provide the following:

• product type
• production year
• product‘s serial number

INSPECTION BEFORE EVERY USE:

1. Visual check.
2. Lead-in cable check.

WARNING: Do not use the device if defects or malfunctions are found.

PERIODIC CHECKS:

1x a week: check that the lead-in cable is undamaged and that the plug is firmly in the socket.
1x a week: check that the device is not exposed to radiant heat.
1x a year: have an engineering inspector check the electrical safety of the device.

MAINTENANCE :

Wipe the device only with a soft and, if needed, lightly moistened cloth.

ENVIRONMENTAL PROTECTION:

Waste Sorting:
This product must not be disposed of in communal waste. Electrical waste in the Czech Republic is disposed of within the Rema System (www.remasystem.cz).
In countries other than the Czech Republic, waste sorting is subject to local regulations.
**** Sorting waste allows recycling and reusing used products and packaging materials. Reuse of recycled material helps protect the environment from pollution and reduces resource consumption.
Local regulations may regulate the method of disposing of household appliances at local collection points or at the point of sale.

TECHNICAL DATA

www.lindr.cz

References

• | Lindr.cz
• | Lindr.cz
• | Lindr.cz
• REMA Systém

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>