Whirlpool MTK1527 Microwave Oven Built-In Trim Kit Installation Guide
- June 13, 2024
- Whirlpool
Table of Contents
MICROWAVE OVEN BUILT-IN TRIM KIT
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models MTK1527, MTK1530
UL listed for use over any electric built-in oven, up to 30″ (76.2 cm) wide
MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
** This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and
others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING.”
These words mean:
WARNING
You can be killed or seriously injured if you don’t immediately follow
instructions.
WARNING**
You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how
to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
INSTALLATION INSTRUCTIONS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
- Measuring tape
- Drill
- Pencil
- 7/64″ drill bit
- Phillips screwdriver
Parts Supplied (not shown to scale
Location Requirements
The microwave oven may be installed over a built-in oven. If installing over a
built-in oven, make sure there is a minimum of 315/16″ (10cm) between the top
of the lower oven cutout and the microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself (without a
built-in oven below). For best usability, we recommend a minimum distance of
36 1/16″ (91.6 cm) from the floor to the cutout floor.
Make sure the surrounding cabinetry has clearance to open and close freely.
Allow a clearance of at least 2″ (5 cm) below the cutout floor (3 15/16″ [10
cm] for installation above a built-in oven), and a clearance of at least 2″ (5
cm) above the cutout opening.
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout
D. Lower cabinets
E. Floor
Required Cutout Dimensions
For minimum depth requirements, see chart.
A. Trim kit frame overhang
B. Cutout for lower oven
C. Recommended region for receptacle location (no less than 6″ [15.2 cm] to
the right of cutout centerline)
D. Cutout centerline
| Receptacle Location | Minimum Depth |
|---|---|
| Within recommended region | 21 9/16″ (54.8 cm) with flush receptacle; |
23 9/16″ (59.8cm) with non-flush receptacle
Outside recommended region| 23 9 /16 ” (59.8 cm) with flush receptacle;
25 9/16 ” (64.9 cm) with non-flush receptacle
NOTES:
- Depth requirements depend upon receptacle and its location within or outside of recommended region. See illustration and chart above.
- Height dimension is critical: 17 1/8″ (43.5 cm) minimum,17 3/16″ (43.7 cm) minimum.
- Width measurement has ±1/16″ (2 mm) tolerance.
- 3 15/16″ (10 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor.
- Trim kit frame extends 13 ⁄₁₆” (2.14 cm) above and below the cutout opening.
*27″ (68.6 cm) trim kit
**30″ (76.2 cm) trim kit
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
- A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a fuse or circuit breaker.
Recommended:
- A time-delay fuse or time-delay circuit breaker.
- A separate circuit serving only this microwave oven.
GROUNDING INSTRUCTIONS
For all cord connected appliances:
The microwave oven must be grounded. In the event of an electrical short
circuit, grounding reduces the risk of electric shock by providing an escape
wire for the electric current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
WARNING: Improper use of the grounding plug can result in a risk of
electric shock. Consult a qualified electrician or serviceman if the
grounding instructions are not completely understood, or if doubt exists as to
whether the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a
qualified electrician or serviceman install an outlet near the microwave oven.
SAVE THESE INSTRUCTIONS
Prepare Microwave Oven
Attach Rails
-
Unplug microwave oven before proceeding with installation.
-
Remove any loose items inside microwave oven.
-
Gently turn microwave oven onto its top, with the door facing forward (toward installer).
-
Align the two rails on the microwave oven bottom, as shown, making sure the flanges are forward and pointing up.
A. Rails (2)
B. 19# screws (4)
C. Microwave oven bottom
D. Table cloth
E. Table -
Secure the rails to the microwave oven bottom using four 19# screws.
Attach Rear Duct
- Gently return microwave oven to its upright position.
- Align the rear duct with the back of microwave oven, as shown.
- Use four short screws to secure top of rear duct to the back of microwave oven, as shown.
A. 19# screws (4)
B. Rear duct
C. Microwave oven
D. Table cloth
E. Table
Prepare Cutout/Cabinet Opening
-
On the cutout floor, find and mark the centerline.
-
Place the bottom duct in the opening, with the flange resting against the bottom front facing of the opening.
A. Cutout floor
B. Centerline
C. Bottom duct
D. Bottom duct flange
E. Front facing -
Align the center arrows on the bottom duct with the centerline drawn in Step 1 above.
A. Bottom duct
B. Cabinet
C. Center arrows, aligned with centerline -
Mark the three mounting holes through the bottom duct onto the cutout floor.
A. Bottom duct mounting holes
B. 123# screws (3)
C. Bottom duct
D.Cabinet -
Using 7/64″ drill, drill pilot holes into the three holes marked in Step 4.
-
Realign and install the bottom duct with three short screws.
-
Using 7/64″ drill, drill pilot holes through the four mounting holes of the bottom duct flange into the bottom front facing of the cutout/cabinet opening.
A. Bottom duct flange
B. Mounting holes
Install the Microwave Oven
-
Position microwave oven near cutout opening.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock. -
Plug in microwave oven.
-
Slide the microwave oven back and into place. The mounting holes of the rail flanges and bottom duct flange will align against the bottom front facing of the cutout/cabinet opening.
-
Secure the microwave oven to the cutout/cabinet by installing four 123# screws into the mounting holes.
Install Trim Kit Frame
-
Position trim kit frame over the opening so that the upper tabs fit inside the rails, as shown.
-
To vertically center the trim kit frame, slide it upward, against the opening, until the upper tabs catch against the top of the rails.
-
Holding the trim kit frame firmly in place, use 7/64″ drill to drill four pilot holes into the front facing of the cutout/cabinet through the mounting hole guides in the upper and lower corners of the trim kit frame.
NOTES:
The holes will be drilled upward from the bottom, and downward from the top at an angle of about 45°.
A. Mounting hole
guide
B. 93# Screws (4 – painted)
C. TK Frame
D. Cabinet
-
Secure trim kit frame to cutout/cabinet by installing four long wood screws (painted) into the pilot holes drilled in Step 3 above.
NOTES:
To ensure vertical centering, install the lower screws first.
To avoid damage to the trim kit frame, do not overtighten screws.
Installation is now complete. Replace any loose items that havebeen removed
from microwave oven cavity.
Save these Installation Instructions for future reference.
W11682371
SP PN W11682371
© 2023 Whirlpool Corporation.
All rights reserved. Used under license in Canada.
Printed in China