ring 169MAILBXB Battery Powered Motion Detector User Guide
- June 4, 2024
- Ring
Table of Contents
Quick Start
-
Set up and install your Ring Bridge.
-
Open the Ring app.
Then, tap Set Up a Device and follow the in-app instructions. -
Scan this code.
This identifies your Ring Mailbox Sensor for fast and easy setup.
For additional help, visit: ring.com/help
IMPORTANT PRODUCT INFORMATION
Safety and Compliance Information
Use Responsibly. Read all 1nstruct1ons and safety information before use.
SAFETY INFORMATION
FAILURE TO FOUOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
BATTERY SAFETY
This product conta1 ns al kalm e batteries. This device requires batteries for use. Only use new 1.5V alkaline or 1.2 NiMH rechargeable AAA-sized batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut. bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the remote as they can become hot and cause burns. Remove all batteries If they are worn out or before storing your Device for an extended period of Lime. Dispose of all batteries in accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak, take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations.
PRODUCT SPECIFICATIONS
Model Number: Ring Mailbox Sensor
Electrical Rating: 3 x AAA·cell batteries
Temperature Rating :-4°F to 122°F (-20″C to SO”C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated, Make
sure you dispose of or recycle, your device In accordance with your locat laws
and regulations.
FCC Compliance: This device complies with part 15 of the FCC Rules. Operation
is subject to the following Iwo conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The oarty responsible for FCC compliance 1s: Ring LLC, 1523 26th St, Santa
Monica, CA USA, 90404
By purchasing or using the product, you agree to the Terms of Service found at
ring.com/terms.
For information on our warranty, theft protection, and Ring Protect Plans, see
ring.com/legal
©2020 Ring LLC or its affiliates. Ring and al! related
marks are trademarks of Ring LLC or its affiliates.
FOR UNITED STATES CUSTOMERS
This device; comp: es with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including 1nterierence that may cause undesired operation.
Information on this device is on file with the FCC and can be found by
Inputting the device’s FCC ID into the FCC 10 Search form available at
https://www.fcc.gov/oet/ea/fccid.
The output power of the radio technology used in the Products is below the
radio frequency exposure limits set by the FCC. Nevertheless, n is advised to
use the product In such a manner that minimizes the potential for human
contact during normal operation This device should be installed and operated
with at least 20 cm between the radiator and your body
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur In a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment For information about recycling your device, go to www.amazon.com/dev1cesupport
FOR CANADIAN CUSTOMERS
Innovation, Science and Economic Development Canada (ISED) Compliance.
This device contains license-exempt transm1tter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any ·nterference, including interference that may cause undesired operation of the device.
Caution: Any changes or mod1ficat1ons to this device not expl1c1tly approved by manufacturer could void your authority to operate this equipment.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
CAN ICES3 (8)/NMB-3(B)
Documents / Resources
| ring
169MAILBXB Battery Powered Motion
Detector
[pdf] User Guide
169MAILBXB, Battery Powered Motion Detector, Powered Motion Detector, Motion
Detector, Detector, 169MAILBXB, Mailbox Sensor, Sensor
---|---
References
- Get Smart Security With Ring Doorbells, Cams & Security Systems
- Legal Information, Support & Resources | Ring
- Terms of Service | Ring
- amazon.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>