Hooks 720501-1-GTS-2008 Clippers Fairfield User Manual
- June 13, 2024
- Hooks
Table of Contents
Hooks 720501-1-GTS-2008 Clippers Fairfield
IMPORTANT SAFEGUARDS!
- Clippers for manicures can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision
WARNING
Cutting blades may become hot after prolonged use.
WARNING
Keep the appliance dry.
Introduction to Parts
Names of Parts of the Product
Body (Figure I)
- Rotor
- O-ring I
- Body upper cover
- Stator
- Retaining screw for switch
- Switch
- Pull the rod of the switch
- Carbon brush components
- O-ring 2
- Body lower cover
- Inlet cover
- Circuit board components
- Lock the block of the power cable
- Retaining screw for lock block of power cable
- Sleeve of power cable
- Power cable
Horsehair clipper (Figure 2)
Horse hair clipper (Figure 2)
I. Adjusting spring
2. Adjusting cap
3. Roller
4. Deflection rocker
5. Small bearing
|
6.Shaft
7. Head bearing
8. Aluminum head
9. Fixed blade
I 0. Moving blade
|
11. Adjusting screw 12.Washer
13.Gear
---|---|---
Sheep hair clipper (Figure 3)
1. Pressure adjusting lock spring
2. Connecting sleeve
|
7. Presser foot
8. Cross arm
|
13. Deflection steel ball I 4. Deflection shaft
3. Sliding sleeve
4. Adjusting cap
5. Aluminum head
6. Moving blade
| 9. Aluminum head plastic cover
10. Fixed blade
11. Blade retaining screw
12. Shift fork
| 15. Pressure rack components
16. Locating pin of pressure rack
17.Nut
18. Gear
New horsehair clipper (Figurel2)
I. Aluminum head
2. Circlips
3. Shaft
4. Sleeve
5. Drive assembly
6. Pressure adjusting screw
|
7. Distance screw
8. Pressure spring
9. Pressure plate
10. Drive block
11. Moving blade
12. Fixed blade
|
13. Blade fixing screws
14. Set screws
15. Screw
16. Gear
Complete Set
- A complete set of machine
- A cleaning brush
- A Manual of Instructions
Application Range
There are two kinds of heads available for choice for this product. If you choose a different product configurations, the clipper heads you receive will be different:
- Head of the horse hair clipper: applicable to shearing of livestock such as cattle and horses.
- Head of sheep hair clipper: applicable to shearing sheep, goats, camels, alpacas, and other animals belonging to the camel family.
- Using this product for other purposes is prohibited, especially for cutting human hair.
Technical Parameters
- Horsehair clipper
- Model: see the nameplate
- Voltage: see nameplate
- Motor power: see nameplate
- Blade speed: see the nameplate
- Protection grade: see nameplate
- Size: 80mmX62mmX295mm
- Weight (power cable excluded): 1030g
- Ambient temperature for operation: 0 “C-40 “C
- Ambient humidity for operation: 10%-90% (relative)
- Noise: :S85dB
- Sheep hair clipper
- Model: see the nameplate
- Voltage: see nameplate
- Motor power: see nameplate
- Blade speed: see the nameplate
- Protection grade: see nameplate
Attention in Operation
- Necessary Attentions Before Use
- Size: 80mmX95mmX320mm
- Weight (power cable excluded): 1200g
- Ambient temperature for operation: 0°C-40°C
- Ambient humidity for operation: 10%-90% (relative)
- Noise: 85dB
Voltage in operation must comply with that on the nameplate
(this machine only uses AC power)
- Avoid touching the moving blade in operation.
- As long as the power is not disconnected, the moving blade area can not be touched even though the machine is turned off; make sure the power is disconnected before installation or removal of the blade/head.
- Prevent contact between the machine body and any kind of liquid. No shearing should be done on wet animal hair. Once liquid enters the body, the machine is no longer insulating, which makes electric shock or short circuit possible.
- Clean the body with a brush only when it is dry.
- In order to avoid danger, the power cable cannot be scattered loosely on the ground.
- Before shearing, arrange the cable in order and avoid winding. The animal should not stand on the cable or between different parts of the cable or winding. The cable should be arranged in order and put beside the body.
- In order to avoid danger, the cable should not contact the heated surface or other objects that will damage its insulation; regular checks should be conducted to see whether there is a failure in the power cable or not.
- Only blades that are designed for this set can be used. Blunt blades or blades with broken teeth should not be used.
- Before shearing the animal, check whether there are foreign matters ( such as sawdust or lint) in the hair.
- Wear proper work clothes. Do not wear clothes that are too loose or ornaments in order to avoid getting stuck in the machine.
- Do not insert foreign matters in the gaps in the machine.
- The operator must be skilled in shearing animal hair. The noise during operation may make animals anxious and disturbed which may result in the operator getting kicked or crushed by animals.
- Tie up the animal and approach from its front. Turn on the machine in a place where the animal can see.
- Before shearing the animal, make sure there are no unrelated people in the workplace.
- Shear at a place with good ventilation. Shearing on explosive or inflammable objects is prohibited.
- Do not share other dangerous animals, especially a carnivore. Please strictly comply with this safety clause.
- It is suggested that an electrical device should be connected to a circuit with a circuit breaker.
- This machine is not suitable for children and physically weak people to use. Children are not allowed to use this machine.
Adjus1ment to the Pressure of Blade
Before the operation, the following adjus1ment for this machine shall be carried out:
Before shearing
Disconnect the power supply. Make sure the moving blade and the fixed blade
are well-fixed. Tighten the adjusting cap until you feel pressure for the
first time.
Warning: If the adjusting cap is too loose, the blade may fly out and
hurt people.
During shearing
Pay attention to that the pressure of the blade should not be set to a value
that is too high, otherwise, the sheared hair may gather in the blade. If the
adjusting cap is not tightened at the beginning of the operation, shearing
will be laborious or even cannot be carried out. At this time, the power
supply should be disconnected and the plug should be pulled out from the power
supply socket. Remove the blade. Clean and lubricate the blade, and then
reassemble as stipulated.
Set the blade pressure properly
If the adjusting cap is too tight, the blade pressure will be too high which
will result in fast blade heating, fast wear, and loud noise. In this case,
the adjusting cap should be unscrewed slowly until the noise reaches a normal
level and a proper shearing result is achieved. During unscrewing, feel the
pressure and set the pressure properly according to need.
Lubrication
Lubrication before and during shearing of horse hair: Apply lubricating oil to the moving blade and the fixed blade slightly (Figure 4). This is of great significance to improving shearing results and prolonging the service life of the machine. Other moving parts on the clipper head should be also lubricated appropriately. Pour a certain amount of lubricating oil into the lubrication port on the clipper head (Figure 5).Lubrication before and during shearing of sheep hair: Apply lubricating oil to the moving blade and the fixed blade slightly (Figure 6). This is of great significance to improving shearing results and prolonging the service life of the machine. Other moving parts on the clipper head should also be lubricated appropriately. Drip in a certain amount of lubricating oil in the lubrication port on the clipper head (Figure 7).
Special oil or paraffin oil meeting the requirements of ofISO-VGl 5 should be used, for this kind of oil is non-toxic and has no side effects causing no harm to skin or mucosa. Paraffin oil will lose 20% of the effect when it is stored for more than 21 days .. Lubricating oil does not only affect the shearing result but also affects the service life of the blade. The blade which has not received sufficient lubrication will give out too much heat in motion, leading to a shortening of the service life of the blade. Therefore the blade and clipper head must be lubricated sufficiently in use (lubrication shall be carried out once every five minutes.).
Turn on/off
There are two positions for the sliding switch; one thereof is shown in Figure
8. 1 position: turn on the button Zero position: turn off button Turn on or
turn off the machine as shown in Figure 8. Before inserting the plug into the
power supply socket, make sure the switch is at the “zero position”.
Installation of blade
Installation of the blade of the horse hair clipper (Figure 9): A set of
blades includes a fixed blade and a moving blade. Make sure the positions of
their faces correspond to each other in blade installation. The installation
should be carried out according to the following steps: Make sure the blade to
be installed is clean and there is no dirt on the blade newly sharpened. An
unclean blade will result in poor shearing results. Press the moving blade
rack slideway into the eccentric shaft and guide the two ends of the rack into
the aluminum head slideway. Aim the two round holes of the fixed blade at the
aluminum head cylinder to put into the aluminum head. Assemble the adjusting
screw. Guide in adjusting spring. Assemble the adjusting cap. Then tighten the
adjusting cap till the cutting surface contacts the cutting surface of the
fixed blade and is confronted with a certain amount of resistance.
Installation of the blade of the sheep hair clipper
A set of blades includes a fixed blade and a moving blade. Make sure the
positions of their face align with each other in blade installation. The
installation should be carried out according to the following steps: Make sure
the blade to be installed is clean and there is no dirt on the blade newly
sharpened. An unclean blade will result in poor shearing results. Put the
moving blade on the pointed cone of the presser foot and make sure the hole
positions face each other. Put the moving blade into the unscrewed screw and
tighten the screw till you can push the moving blade to move slightly with
your hand. Turn over the machine with the adjusting cap upwards again. The
most important thing to do at this moment is to aim the moving blade at the
center of the fixed blade with the cutting edge of the tooth top of the fixed
blade having a distance of about 1.5-2.0mm to the tooth top of the moving
blade (Figure 10).
Once the blades are adjusted, tighten the retaining screw of the fixed blade to lock the position of the fixed blade. Check whether the blade is locked in the right place or not. The pointed cones of the two presser feet must aim at the round holes of the moving blade (Figure 11). Now tighten the adjusting cap till the cutting surface of the moving blade contacts that of the fixed blade, and the pointed cones of the two presser feet are inserted into the round holes of the moving blade with a certain amount of resistance.
Installation of the blade of the new horse hair clipper (Figure 13)
Loosen the pressure adjusting screw (part 6) and place the machine on a hard
surface so that the blade fixing screws (part 13) lie uppermost. Loosen the
two blade fixing screws and remove the two old blades. Ensure that the new
clipper blades are clean. Particular care should be taken to ensure that the
ground surfaces are free of dirt; if not, even newly ground clipper blades
will not clip satisfactorily. Place the new moving blade (part 11) in the
guide points of the drive assembly (part 5); then place a few drops of oil on
the ground surfaces. Now push the new fixed blade (part 12) between the
loosened screws. What is now important is that you adjust the blades against
each other in such a way that the ground surface of the fixed blade projects
approx.1.5-2.0 mm beyond the tips of the moving blade. Once you have adjusted
the clipper blades, set the position of the fixed blade and tighten up the
blade fixing screws.
Maintenance
Before maintenance operation, the power supply should be disconnected, and the plug should be pulled out. Even if the machine body is turned off, no relevant operation should be done in the vicinity of the blade as long as the plug is connected to the power supply. Make sure the power supply is disconnected whenever an operation is to be done to the blade/clipper head.
Cleaning
Cleaning of clipper head and blade
After shearing is finished, wipe the lubricating oil out of the blade with a
dry cloth and clean the clipper head and blade with a dry brush carefully.
Then apply lubricating oil to prevent rust. Even a very small rust spot on the
blade could bring a significant influence on the shearing result and can even
make the blade lose efficiency. Therefore, rust prevention should be paid
great attention to.
Blade Sharpening
Only a sharp blade should be used. Replace the blades that are blunt and lose
teeth. A special sharpener should be used for blade sharpening, and the
sharpener should be operated by technicians who are trained by service
service-providing agency.
Replacement of Clipper Head (spare)
For the replacement of the clipper head, the two screws of the clipper head
should be unscrewed. Remove the original head assemble the new head (the new
head needs to be lubricated) and then retighten the screws.
Storage of Machine
This machine should be stored with the packaging box in a cool and dry place.
If there is doubt of any liquid entering the machine, please do not use the
machine, for it may result in electric shock. The machine should be sent to
the maintenance department for treatment. When the machine is not used, please
keep it in a proper manner, which means cleaning, lubrication,loosing pressure
and then storing it in a storage box which is put in a dry place with good
ventilation that is out of children’s reach.
Troubleshooting Common Failures
In case any failure included in the following list occurs, please contact a professional repair institution for troubleshooting and repair.
Troubleshooting of failures of horse hair clipper
| Failure | Reason of failure | Troubleshooting method |
|---|
The moving
move.
| blade| cannot| There is failure in the gear.| Replace gear.
The blade
pressurized.
| cannot| be| The adjusting spring
damaged.
| is| Replace the adjusting spring.
Vigor is lacked in shearing.| The moving blade and
fixed blade gets blunt.
| the| Re-sharpen blades.
The pressure on the blade is
too low.
| Add pressure through
adjusting the adjusting cap.
The clipper head is too hot.| The pressure on the blades is too high.| Reduce pressure on blades and sharpen blades as
necessary.
There is no lubricating oil on
blades.
| Add lubricating oil.
There is no lubricating oil in the moving blade rack
slideway.
| Add lubricating oil to the lubrication port on the clipper
head.
The motor cannot operate.| The machine does not power
up.
| Check connection.
The power cable is damaged.| Send it to the service center
for inspection and replace the power cable.
The switch and motor
damaged.
| are| Send them to the service
center to repair.
The motor is too hot.| The air filter is blocked and air
can not flow freely.
| Use a brush to clean the filter
screen.
| The pressure on the blades is too high.| Do not screw the pressure button of blade too tight. If normal operation is still not achieved, sharpening or replacement of blades is
required.
---|---|---
Failure|
---|---
The moving blade cannot
contact all contacting surfaces of the fixed blade to move.
|
The move.| moving| blade| cannot|
The adjusting cap gets loose automatically.| The pressure lock spring is lost,
or gets defonned and
loses elasticity.
| Replace the lock spring.
---|---|---
The connecting sleeve gets
loose.
| Rebind with special binder for
screw thread.
The blade cannot be pressurized.| The pressure rack is
damaged.| Replace the pressure rack.
The sliding sleeve gets lost or
damaged.
| Replace the sliding sleeve.
The shift fork gets worn.| Replace the shift fork.
The presser foot gets worn.| Replace the presser foot.
Vigor is lacked in shearing.| The moving blade and the
fixed blade get blunt.
| Re-sharpen blades.
The pressure on the blade is
too low.
| Add pressure through
adjusting the adjusting cap.
Shearing cannot be carried out.| The fixed blade is not installed well.| Adjust the fixed blade so as to make the tooth surface of the moving blade 1.5-2.0 mm
behind the fixed blade.
The rolling steel ball gets lost.| Replace the rolling steel ball.
The gear is damaged.| Replace the gear
The clipper head gets worn.| Replace the clipper head
The clipper head is too hot.| The pressure on the blades is
too high.
| Reduce pressure on blades and
sharpen blades as necessary.
There is no lubricating oil on
the rolling steel ball.
| Add lubricating oil to the
lubrication port on the clipper
| head. |
|---|
There is no lubricating oil and
grease in the sliding sleeve.
| Add lubricating oil & grease
into the sliding sleeve.
The motor cannot operate.| The machine does not power
up.
| Check connection.
The power cable is damaged.| Send it to the service center for inspection and
replace the
power cable.
The switch
damaged.
| and| motor| are| Send it to the service center to
repair.
The motor is too hot.| The air filter is blocked and air can not flow freely.|
Use a brush to clean the filter screen.
The pressure on the blades is too high.| Do not screw the pressure button of
blade too tight. If normal operation is sti II not achieve d, sharpening or
replacement of blades is
required.
Environment Protection and Treatment Measures
The user has the obligation to dispose of the product properly when he/she no
longer uses it. Please comply with relevant state regulations.
Drawings
Conforms with the requirements in the relevant EU directives regulations CE:
Information on the disposal of Waste Electrical & Electronic Equipment (WE)
This symbol on the products and accompanying documents means
that used electrical and electronic products should not be mixed with general
household waste. For proper disposal for treatment, recovery, and recycling,
please take these products to designated collection points where they will be
)t accepted on a free-of-charge basis. In some countries, you may be able to
return your products to your local retailer upon the purchase of a new –
product. Disposing of this product correctly will help you save valuable
resources and prevent any possible effects on human health and the
environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>