tp-link TL-POE160S Power Over Ethernet POE Injector Installation Guide
- June 13, 2024
- tp-link
Table of Contents
Installation Guide
PoE Injector
LED Explanation
PWR
On: Power on
Off: Power off
PoE (Only for TL-POE170S)
On: Normal power supply
Off: No powered device connected
Flashing: Abnormal power supply
Note:
For simplicity, we will take TL-POE160S for example in this Guide.
Connection
Note:
- The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP and PoE IP Phone through an Ethernet cable.
- For TL-POE170S, plug the product into the wall outlets with earthing connection through the power supply cord.
Specifications
General Specifications
Standards| IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af,
IEEE 802.3at
IEEE 802.3bt (Only for TL-POE170S)
---|---
LED| TL-POE160S: PWR
TL-POE170S: PWR, PoE
Cable Type| UTP/STP of Cat. 5 or above (based on the standards
that the connected devices comply with)
Ports| 10/100/1000 Mbps RJ45 DATA IN Port
10/100/1000 Mbps RJ45 PWR+DATA OUT Port
AC 100–240 V 50/60 Hz Power Input Port
Maximum
Power Supply| TL-POE160S: 30 W
TL-POE170S: 60 W
Dimensions
(L×W×H)| TL-POE160S: 125×59.4×36.8 mm
TL-POE170S: 154.7×70×42 mm
Wall
Mountable| Ye s
Distance Between
Mounting Holes| TL-POE170S: 102 mm
Environmental and Physical Specifications
Operating Temperature| TL-POE160S: 0˚C to 40˚C (32˚F to 104˚F)
TL-POE170S: 0˚C to 45˚C (32˚F to 113˚F)
---|---
Storage Temperature| -40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity| 10% to 90% RH non-condensing
Storage Humidity| 5% to 90% RH non-condensing
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible..
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
FAQ
Q1. Can the PoE injector supply power to a PoE device which doesn’t have a gigabit PoE port?
A: Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps.
Q2. What can I do if my PoE injector doesn’t supply power to the powered device or the supplied power is unstable?
A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE function. A2: Ensure the power consumption of the PD doesn’t exceed the maximum power supply of the PoE injector, otherwise the overload protection of the PoE injector will be activated. The quality and length of the Ethernet cable may influence the reception of the power supply.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit https://www.tp-
link.com/support, or simply scan the QR code.
http://www.tp-link.com/support
If you have any suggestions or needs on the product guides, welcome to email [email protected].
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/support/ce.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016.
The original UK Declaration of Conformity may be found at https://www.tp-
link.com/support/ukca