BRIZO 77290 Wall Mount Toilet Tissue Holder User Guide
- June 13, 2024
- BRIZO
Table of Contents
BRIZO 77290 Wall Mount Toilet Tissue Holder
Product Information
- Product Name: CharlotteTM Bath Collection Tissue Holder
- Model Number: 77290
- Dimensions: 6 3/4 inches (171.45 mm)
- Cleaning and Care: To clean, wipe gently with a damp cloth and blot dry with a soft towel. Do not use harsh abrasives or polish as it may damage the product’s finish.
Product Usage Instructions
- Ensure that the tissue holder is mounted securely. If possible, mount it into a wall stud. Use a stud finder or tap on the wall to locate a wall stud. Place the mounting stud in the desired location and ensure it is level.
- Mark the position of the holes on the wall for both mounting studs.
- If you have located a wall stud for one or both ends, drill 1/8-inch (3mm) holes and mount the mounting stud using the provided #8 screws. Skip to step 4 if both mounting studs were mounted into wall studs.
- If mounting into ceramic tile or solid surface, place masking tape on the mounting area before marking the location to prevent the drill bit from sliding. Drill 1/4-inch diameter holes where indicated. Push in anchors until flush with walls. Note: Sheetrock or hollow doors may require molly or toggle bolts, which are included with this product.
- With the mounting stud oriented as shown, place it over the installed anchors making sure the notch on the post points downward, and install screws. Repeat for the second mounting stud.
- Position the bodies over the mounting studs and tighten the set screws.
- Squeeze the ends of the spring-loaded rod inward, then slowly release between the bodies to assemble.
Warranty Service and Replacement Parts
To obtain warranty service or replacement parts, you can call
1-877-345-BRIZO (2749) or contact Brizo Kitchen & Bath Company online or by
mail. Make sure to provide your model number and date of purchase.
In the United States and Mexico:
Brizo Kitchen & Bath Company
E. 111th Street
- Indianapolis , IN 46280
- Attention : Warranty Service
- https://www.brizo.com/customer-support/contact-us
In Canada
- Masco Canada Limited, Plumbing Group Technical Service Centre
- 350 South Edgeware Road
- St. Thomas, Ontario, Canada N5P 4L1
- https://www.brizo.com/customer-support/contact-us
What Is Not Covered
This warranty does not cover Brizo products purchased from unauthorized
sellers. Visit Brizo.com to see a list of authorized online resellers.
Model
You may need
CHARLOTTE™ BATH COLLECTION
TISSUE HOLDER
CLEANING AND CARE
Care should be given to the cleaning of this product. Although its finish is
extremely durable, it can be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry with a soft towel.
NOTE: If possible, it is best to mount your tissue holder into a wall stud. Try to locate a wall stud with a stud finder or by tapping on the wall. Place mounting stud (1) in the desired location. Ensure the mounting stud is level; then, mark the position of the holes (2) on the wall. Repeat for 2nd mounting stud, spaced as noted above.
If you were able to locate a wall stud for one or both ends, drill 1/8″ (3mm)
holes and mount the mounting stud with the two #8 screws provided. (Skip to
step 4 if both mounting studs were mounted into wall studs.)
On ceramic tile, try to locate the mounting hole locations on a grout line. If
mounting into ceramic tile or solid surface, place masking tape on the
mounting area before marking the location to prevent the drill bit from
sliding. To drill through ceramic tile, obtain a 1/4″ diameter carbide drill
bit. Drill 1/4″ diameter holes where indicated. Push in anchors (1) until
flush with walls.
Note: Sheetrock or hollow doors may require molly or toggle bolts, which are included with this product.
With the mounting stud (1) oriented as shown, place it over the installed anchors (2) making sure the notch on the post points downward and install screws (3). Repeat for second mounting stud.
- Position bodies (1) over mounting studs (2) and tighten set screws (3).
- Squeeze the ends of the spring loaded rod (4) inward, then slowly release between the bodies to assemble.
Replacement Parts
Note: RP includes parts for 2 sides
RP70590
Mounting Hardware
RP70591
Set Screws (2)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>