ANKER A1770 Powerhouse 757 Portable Power Station User Manual

ANKER A1770 Powerhouse 757 Portable Power Station

Product Information

• Product Number: A1770 51005003357 V02
• Product Name: Anker 757 Portable Power Station (PowerHouse 1229Wh)
• Included Accessories: Dust-proof Bag, AC Charging Cable, Solar Charging Cable, Car Charging Cable, User Manual

Product Usage Instructions

1. Recharging Your Power Station :
   • AC recharging(1000W Max): Connect the AC charging cable to a wall outlet and the AC input port on the Power Station.
2. Solar panel recharging (300W Max): Connect up to 3 100W solar panels in parallel using a solar charging cable and connect it to the XT-60 DC input port on the Power Station.
3. Car recharging (120W Max): Connect the car charging cable to a car’s output port and the car input port on the Power Station.

Powering Your Devices:

• AC charging: Press the AC button and connect your devices to the AC output ports.
• USB charging: Connect your devices to the USB ports.
• Car socket charging: Turn on the car socket and connect your devices to start charging.

Uninterruptible Power Supply (UPS):

• To use the UPS function, connect the Power Station to a wall outlet using the AC charging cable. Press the button and connect your devices via the AC output ports.

Power Saving Mode:

• Switching on the power saving mode will automatically turn off the Power Station once all your devices are fully charged.
• Switching off the power saving mode enables stable charging over an extended period, such as for timelapse photography or using a CPAP machine while sleeping.

Light:

• Ambient light: Press the button once to turn on the ambient light. Press again up to 2 times to switch between brightness levels.
• SOS mode: Press and hold the button for 2 seconds to turn on SOS mode.

LCD Screen Guide:
Refer to the user manual for detailed information on using the LCD screen. 7.

Troubleshooting:

• AC recharging failure: Check if the overload protection switch is switched on. If so, press it down to reset and resume recharging.
• AC charging failure : If AC charging is unavailable, try unplugging one or more connected devices that may be exceeding 1500W.
• Resetting your Power Station : If the Power Station isn’t working correctly, press the reset button located on the front of the product for 1 second to perform a factory reset.

For more information and support, visit anker.com/support or contact support@anker.com.

Specifications:

• Cell Capacity: 1229Wh
• AC Input Voltage: 220-240V~, 50Hz/60Hz
• AC Input Power (Charging): 1000W Max
• AC Input Power (Bypass Mode): 1500W Max
• Solar Panel Input: 11-30V, 10A (300W Max)
• Car Charger Output: 12V, 10A
• AC Output : 220-240V, 50Hz, 1500W Max
• USB-A Output: 5V, 2.4A (2.4A Max Per Port)
• USB-C Output (100W): 5V 3A/9V 3A/15V 3A/20V 3A/20V 5A (100W Max)
• USB-C Output (60W): 5V 3A/9V 3A/15V 3A/20V 3A (60W Max)
• UPS Discharging Temperature: N/A
• Charging Temperature: N/A
• Size: N/A
• Net Weight: N/A
• Gross Weight: N/A

What’s in the Box

Overview

Recharging Your Power Station

• AC recharging (1000W Max)
  Recharge your Power Station by connecting to a wall outlet with the AC charging cable.

• Solar panel recharging (300W Max)
  Recharge your Power Station by connecting up to 3 100W solar panels in parallel with a solar charging cable

• Car recharging (120W Max)
  Recharge your Power Station by connecting to a car’s output port with the car charging cable

When your portable power station only has 1% battery remaining, the Remaining Battery indicators will flicker to remind you to recharge the product.

Powering Your Devices

• AC charging
  Press the AC button and connect your devices to the AC output ports.

• USB charging
  Connect your devices to the USB ports.

• Car socket charging
  Turn on the car socket and connect your devices to start charging.

Uninterruptible Power Supply (UPS)

To use the UPS function, connect your Power Station to a wall outlet with the AC charging cable, then press the button and connect your devices via the AC output ports.

Power Saving Mode

• Switching on the power saving mode prevents wasting power by automatically turning off the Power Station once all your devices are fully charged.
• Switching off the power-saving mode will enable stable charging over an extended period, such as for timelapse photography or for sleeping with a CPAP machine.

Light

• Ambient light
  Press the button once to turn on the ambient light, and press again up to 2 times to switch between brightness levels.

• SOS mode
  Press and hold the button for 2 seconds to turn on SOS mode.

LCD Screen Guide

1. LCD Screen Button
2. Press the button to turn on the LCD screen.
3. Power Saving Mode
4. High-Temperature Alert: When this icon shows, stop using the product and leave it to cool down until the icon disappears.
5. Low-Temperature Alert: When this icon shows, stop using the product until the icon disappears.
6. USB-C Output Port
7. USB-A Output
8. Car Charging
9. AC Charging and Voltage Frequency
10. Remaining Battery
11. Time to Recharge / Remaining Battery in Hours
12. Current Input Power
13. Current Output Power

Trouble Shooting

AC recharging failure
When AC recharging is unavailable, check to see if the overload protection switch is switched on. If so, press it down to reset, and then recharging can resume.

AC charging failure
If AC charging is unavailable, the connected devices may exceed 1500W. Try unplugging one or more of the connected devices to see if this resolves the issue.

Resetting your Power Station
If your Power Station isn’t working correctly, press the reset button (located on the front of the product) for 1 second for a factory reset. If the Power Station still doesn’t work, please visit support@anker.com

FAQ

Q1: Why does the Power Station’s battery drain even when no devices are connected?
When the AC and Car Socket control button is turned on, even if no devices are being charged, there will still be a certain amount of no-load power consumption. To avoid this, make sure the AC and Car Socket charging button is off or turn on the power saving mode when you’re not using the Power Station.

Q2: What’s the max power output of the AC output ports?
The AC output ports can deliver a maximum of 1500W to connected devices.

Q3: Can I recharge the product while charging connected devices?
Yes.

Q4: Can this product power a CPAP machine?
Yes, but make sure to turn off the power-saving mode first.

Q5: What kind of solar charger can charge this product?
Any 11-30V solar charger with an XT-60 female connector.

Specifications

Attention: Not permitted on aircraft.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : When using this product, basic precautions should always be followed, including the following: Read all the instructions before using the product.

• To reduce the risk of injury, close supervision is necessary when the product is used near precautions
• Do not put your fingers or hands into the product.
• Do not expose the product to rain or snow.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to precautions

To reduce the risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the product.

• Do not use the product over its output Overload outputs above the rating may result in a risk of fire or injury to persons.
• Do not use a product that is damaged or Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Do not operate the product with a damaged cord or plug, or a damaged output cable.
• Do not disassemble the Take it to a qualified service person when service or repair is required.

Incorrect reassembly may result in a risk of fire or electric shock.

• Do not be exposed to fire or high Exposure to fire or temperatures above 130°C may cause an explosion. To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed servicing.
• Have servicing performed by a qualified repair person using only identical replacement This will ensure that the safety of the product is maintained.
• When charging a device, the product may feel warm, this is a normal operating condition and should not be cause for
• When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
• Do not clean the product with harmful chemicals or
• Misuse, dropping, or excessive force may cause product
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each

CAUTION : Risk of explosion if the battery is replaced by an incorrect one.

• Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;
• Leaving a battery in an extremely high-temperature environment can result in an explosion or leakage of flammable liquid or gas;
• A battery subjected to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas;
• Unplug the AC power cable to disconnect it from the line

WARNING : GROUNDING INSTRUCTIONS

This product must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded by all local codes and ordinances.

WARNING   Improper connection of the equipment grounding conductor may result in an electric shock. Check with a qualified electrician if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

Storage and Maintenance instructions

1. Please store the product between 32°F-104°F. Avoid exposing the product to rain or using the product in a humid
2. To preserve battery lifespan, please discharge the battery to 30% and recharge it to 60% every three
3. Please keep the product laid flat during use, when charging, and during

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

Company Name : Fantasia Trading LLC Address : 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764 Telephone : +1-800-988-7973

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>