ergotron 98-649-251 Top Mount Scanner Holder User Guide
- June 13, 2024
- ERGOTRON
Table of Contents
ergotron 98-649-251 Top Mount Scanner Holder
Product Information
| Product Name | FUHILT |
|---|---|
| Manufacturer | ERGOTRON |
| Model Number | 9(6$$WWDFK |
| Product Features | – Adjustable height and tilt |
– Supports up to 6 monitors
– Durable construction
– Easy installation
Website| www.ergotron.com
Contact Information| USA:
1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-120-3051
Japan: japansupport@ergotron.com
Product Usage Instructions
- Ensure you have all the necessary components for assembly.
- Identify the desired height and tilt angle for your monitors.
- Place the base of the product on a stable surface.
- Attach the monitor brackets to the back of each monitor.
- Securely mount the monitors onto the product’s arms.
- Adjust the height and tilt of each monitor to your preference.
- Tighten any adjustment knobs or screws to secure the monitors in place.
- Connect the necessary cables to each monitor.
- Test the stability and functionality of the setup.
WHATS IN BOX
Tools Needed
Weight Capacity
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
INSTALLATION INSTRUCTION
- Customer supplied fasteners
- Tilt
Route Cables to the Wall
Route Cables to CPU Under Worksurface
Adjustment Step
- Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments.
- This product should move smoothly and easily through the full range of motion and stay where you set it.
- If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
- Depending on your product and the adjustment, it may take many turns to notice a difference.
- Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
- DO NOT exceed torque of 100 cm-kg (86 in-Ib).
Power tools NOT recommended
- Increase Lift Strength
- If the mounted weight is too heavy or this product does not stay up when raised, then you’ll need to increase Lift Strength:
- Decrease Lift Strength
- If the mounted weight is too light or this product does not stay down when lowered, then you’ll need to decrease Lift Strength:
- If the mounted weight is too light or this product does not stay down when lowered, then you’ll need to decrease Lift Strength:
Tilt – Forward and Backward
- DO NOT exceed torque of 40 cm-kg (34 in-Ib).
Power tools NOT recommended
- Increase Lift Strength
- If the mounted weight is too heavy or this product does not stay up when raised, then you’ll need to increase Lift Strength:
- Decrease Lift Strength
- If the mounted weight is too light or this product does not stay down when lowered, then you’ll need to decrease Lift Strength:
Safety
-
Caution: Leave enough slack in cable to allow full range of motion.
- To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual.
- Failure to follow these instructions may result in equipment damage or personal injury.
-
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed.
-
For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
-
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
-
For the latest User Installation Guide please visit: www.ergotron.com
-
For Warranty visit: www.ergotron.com/warranty
-
For Service visit: www.ergotron.com
-
For local customer care phone numbers visit: http://contact.ergotron.com
-
NOTE: When contacting customer service, reference the serial number.
-
USA: 1-800-888-8458 Europe: +31 (0)33-45 45 600
-
China: 400-120-3051
-
Japan: japansupport@ergotron.com
-
© 2023 Ergotron, Inc. All rights reserved. CareFit™ is a registered trademark of Ergotron, Inc.
-
While Ergotron, Inc. makes every effort to provide accurate and complete information on the installation and use of its products, it will not be held liable for any editorial errors or omissions (including those made in the process of translation from English to another language), or for incidental, special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction.
-
Ergotron, Inc. reserves the right to make changes in the product design and/or product documentation without notification to its users.
-
For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Ergotron, Inc., 1181 Trapp Road, Eagan, Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign.
-
Ergotron is a registered trademark of Ergotron, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>