WONLINK M0305498 Wi-Fi Extender Repeater Installation Guide

WONLINK M0305498 Wi-Fi Extender Repeater

Introduction

Product Structure

1. Unplug it in a thunderstorm to prevent damage.
2. Keep away from the heat source and keep ventilation.
3. Pay attention to waterproofing during storage, transportation and operation.

Simple Installation Steps

1. Plug in and wait for the power light and WiFi light up.

2. Wait 1-2 minutes, connect to WiFi “WONLINK XXXX-
   2G” or “WONLINK XXXX 5G”.

3. When the extender is set up for the first time, the configuration webpage will pop up automatically. If not, launch a web browser and enter “192.168.10.1” in the address field, enter the password “admin”, and Click “SET PASSWORD”.

4. Scan and select the WiFi you want to extend. Enter your WiFi password (Pre-Shared Key should be the same as your network password), and click “Save Setting” to complete the setup.

5. After the setup is complete, it will reboot automatically. Then go to your WiFi list, reconnect WiFi “XXX-2G” or “XXX-5G” (your new extender WiFi), the password is your original WiFi password and enjoy the WiFi.

Warm Tips
WiFi5/WiFi6 Switch: The extender selects WiFi 5 or WiFi 6 protocol, default protocol is WiFi 6.
WPA3 Encryption: When it is enabled, the extender is WPA2/WPA3 hybrid encryption.
Combine WiFi: When it is enabled, it merges 2G and 5G signals to one SSD and only shows the SSID name on the WiFi list.
Sync Your Device: When it is enabled, the new WiFi name will be the same as your original WiFi name and no need to reset it.

Introduction of Working Mode

There are four working modes: Repeater Mode, Bridge Mode, AP Mode, Router Mode (PPPoE, Static IP, Dynamic

1. Repeater Mode: Wireless connection to extend existing WiFi coverage.
2. Bridge Mode: Similar to repeater mode, but will form an SSID independently. Setups: and set in Advanced Mode.
3. AP Mode: Wired connection, converts wired Internet connection into wireless WiFi for expansion.

Setups: Enter the Software management page, and click AP mode. To facilitate management, the IP address and default gateway entered here should be the IP network segment of the superior router, and the IP address should not allowed to conflict with the IP of the superior router. After the setup is completed, the WAN port of the device is connected to the external network, and the management device can be accessed via the IP address you set.

1. Note: When accessing the external network under AP mode, the IP address network segment obtained wireless by other mobile devices accessing the AP is assigned by the superior device.
2. According to the default settings, no need to set the specific intranet IP address of the device. Or you can manually set the IP address of the network card for the computer’s local connection.
3. After setting, the WAN port is connected to the external network, and other mobile devices can connect to the Internet by wireless connecting to the WiFi extender.

Router Mode: Connects to any modem and works as a standalone router.
Setups: Enter the software management page, and select the Router mode, there are “PPPoE”, “Static ‘P” and “Dynamic IP” three choices.

1. POE Dial-up Mode: Under this mode, you need to fill in the Internet account and password from the network service provider.
2. Static IP Mode: Under this mode, you need to fill in the IP address, subnet mask, gateway and primary DNS address from the network service provider.
3. Dynamic IP Mode: Under this mode, the WAN port can only access the Internet by assigning IP to the superior network device.
4. IPV6 Setting: Support DHCPV6 client, static IP and Repeater function, the DHCPV6 client function is enabled by default.

IPv6 Setting

• Click and select to enter the IPv6 setting page.
• IPv6 Status: Displays the information about the IPv6 address obtained by the device.
• IPv6 Setting: Set the IPv6 LAN and WAN information.

Mesh Setting
Tips

1. The Mesh controller node needs to be enabled in Router mode or AP mode. It is recommended to use it in Router mode.
2. The Mesh network consists of a management node and at least one agent node.
3. After enabling Mesh, you need to click the “Trigger Easy Mesh” button on the two node sides to pair Mesh.
4. The Mesh pairing process takes about 2 minutes. After 2 minutes, go to the management node page, you can view the status of Mesh.
5. If the Mesh is not formed successfully. Try pairing again after clicking the “Reset EasyMesh to Default” button on the Mesh setting page.

Click and select to enter the Mesh setting page.
EasyMesh Status: After the Mesh is successfully formed, see the schematic diagram of the Mesh.

EasyMesh Settings

1. Select the Mesh role.
2. If you choose the role of “Controller”, you need to set the SSID and password of the Mesh. Click “Settings” to save the configuration and enable the Mesh function.

Mesh Pairing

• After enabling Mesh, a button for Mesh pairing will appear on the page.
• Click the “Trigger Easy Mesh” button on the sides of the two nodes to start building Mesh.

Light Control Status

• You can turn off the lights in advanced settings.
• NOTE: The power light cannot be turned off.

Q&A

1. What’s the role of a WiFi extender?
   A: Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Please note that it can’t increase the WiFi speed of your router, the speed of the extending WiFi will be reduced.

2. Where should I place the WiFi extender?
   A: We would suggest that after setting up successfully, please move this WiFi extender halfway between your router and your weak signal area. The location you choose to install it must receive a WiFi signal of a certain strength, otherwise, it is prone to dropouts because the original WiFi signal is too weak.

3. How to reset the WiFi extender?
   A: Press the WPS/Reset button of your extender for 10 seconds then release it, and wait to restore factory settings, when you can search the initial WiFi signal of the extender again through your mobile phone or laptop, it means the reset is successful.

4. Why the WiFi keeps disconnecting?
   A: The installation is too far away from the router, causing the WiFi signal received by the repeater to be too weak. If you still have a WiFi disconnecting problem, please contact us via wonlinkservice@163.com.

5. After the setup is successful, connect to WiFi but cannot access the Internet.
   A: There would be 3 reasons, setup unsuccessfully, WiFi password entered incorrectly, conflict with the host router.

6. Connect the WiFi signal of the extender and re-enter the IP address to check the connection status. If it says “connecting” or “not connected”, it means that the setting is unsuccessful, you can try to change the browser to setup.

7. WiFi passwords can not contain special characters, such as @, %, #, *, etc., and no more than 32 characters, if it does not meet this requirement, it is recommended that you change the host router’s WiFi password and then configure it.

8. Reboot the host router and reset the extender before configuring.

9. When logging in to the IP address, it prompts that the password is incorrect.

10. Repeater default user name: admin, default password: admin, confirm whether the password is entered correctly.

11. Cut off the power of the repeater, plug it in again, then restore the factory settings, connect the repeater WiFi, and log in to the IP again.

12. What if the WiFi extender has broken?
    A: We always offer friendly customer service for every customer. If there are any problems, please don’t hesitate to contact us via wonlinkservice@163.com, we will solve it as soon as possible.

Maintenance Regulations

Dear Valued Clients,
Thank you for purchasing WONLINK products. To protect your rights and interests in after-sales service, please read the following maintenance regulations.
The following does not belong to free mainte- nance, our company can provide paid service, please note:

• Damage resulting from improper installation/mounting, improper use or storage of the product, or failure to observe the operating instructions, and/or safety notes;
• Beyond the limited warranty,
• Unauthorized alteration, tearing up the product bar code;
• Without authorization to change the settings file or recompilation;
• Unexpected factors or human actions lead to product damage, such as improper input voltage, temperature,wa- ter mechanical damage, break, rust or oxidation product of serious etc;
• Other failures or damages not caused by the product’s design, technology, manufacturing, quality, etc.

Customer Data

CONTACT

• If you have any questions, please contact us by
• E-mail wonlinkservice@163.com and we will help you as soon as possible.
• Website: www.szwonlink.com
• Email: wonlinkservice@163.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>