milwaukee RBA-2 1 2 Router Track Adapter Instruction Manual

milwaukee RBA-2 1 2 Router Track Adapter

Product Information

Product Name: 1/2 Router Track Adapter
Model Number: RBA-2

Important Safety Instructions:

• To reduce the risk of serious injury, read all safety warnings, instructions, illustrations, and specifications provided by the router and guide rail manufacturer before beginning work.
• Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

WARNING : To reduce the risk of serious injury, read all safety warnings, instructions, illustrations and specifications provided by the router and guide rail manufacturer before beginning work.

Specifications

• Functional Description: Attaching to Router Base
• Connection Rods: 2
• Thumb Screw Storage: Yes
• Handle: Yes
• Anti-tip Knob: Yes
• Rail Adjustment Knob: Yes
• Gauge Block: Yes

Cat. No. …………………………………………………….. RBA-2
Maximum offset………………………………….. 50.8 mm (2″)
Compatibility ………………….. MILWAUKEE® Guide Rails

Assembly

WARNING : Always remove battery from tool before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.

Assembling
Assemble the track adapter, as shown.

Attaching to Router Base (M18 FR12, RBA-1):

1. Remove the battery pack.
2. If present, remove the U-ring from the base.
3. Slide the connection rods equally into the accessory holes of the base until the bar is flush against the router base.
4. Move the two thumb screws from storage into the threads of the router base to secure the rods to the router base.

Attaching to a Guide Rail:

1. Remove the battery pack.
2. Place the track adapter onto the guide rail, aligning the channel on the track adapter with the guide rail channel.
3. Loosen the rail adjustment knobs.
4. Check for play between the track adapter and guide rail.
5. Adjust both rail adjustment knobs to remove play between track adapter and guide rail while still allowing the track adapter to slide smoothly along the guide rail. For best results, the guide clearance of the router must be very small.
6. Engage the anti-tip feature by pressing the button in and rotating the anti-tip knobs.

Offset

1. Remove battery pack.
2. Loosen the rod thumb screws.
3. Using the offset scale, slide the track adapter away from the router base to the desired offset (up to 50.8mm (2″)).
4. Tighten both rod thumb screws to lock the offset.

Using the Gauge Block

1. Remove the battery pack.
2. Mark the cut line on the workpiece.
3. Select a bit and note the bit diameter.
4. Set the guide rail on the workpiece.
5. Place the gauge block against the guide rail.
6. Adjust the guide rail and gauge block until the bit diameter edge marking of the gauge block (that matches your bit diameter) is parallel to the cut line.
7. Secure the guide rail to the workpiece.
8. Insert the bit into the router.
9. Attach the router to the guide rail.
10. Set the guide rail offset to 0 so the router is flush up against the workpiece.

SYMBOLOGY

• Read operator’s manual
• Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

FUNCTIONAL DESCRIPTION

1. Offset scale rod
2. Connection rods
3. Thumb screw storage
4. Handle
5.  Anti-tip knob
6. Rail adjustment knob
7. Rod thumb screw
8. Bar (for M18 FR12, RBA-1)
9.  5 mm hex wrench
10.  Gauge block
11. M18 FTR conversion parts
12. Guide rail channel

Converting Track Adapter for use with M18 FTR Laminate Trimmer

1. Remove battery pack.
2. Remove the rod assembly from the track adapter.
3. Disassemble the rod assembly Connection rod screws are T20; Offset scale rod is †10).
4. Replace the standard adapter plate with the laminate trimmer adapter plate.
5. Reassemble the rod assembly.
6. Insert the rod assembly into the track adapter.
7. Place the track adapter onto the guide rail.
8. Position laminate trimmer against laminate trimmer adapter plate (aligning slot in plate with matching boss on trim router).
9. Tighten the bolt with washer using the 5 mm hex wrench to secure trim router to guide rail adapter.

WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to product sold by authorized dealers in Australia and New Zealand.

SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy DutyTM. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, please contact your authorised MILWAUKEE® dealer. For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE® Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928) or visit milwaukeetool.com.au/milwaukeetool.co.nz.

Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005

Milwaukee Tool (Australia)
26 – 40 Nina Link, Dandenong South, Victoria, 3175, Australia

Milwaukee Tool (New Zealand)
274 Church Street, Penrose, Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP. PROFESSIONALLY MADE IN CHINA PRINTED IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>