BRISTAN HOU 1-2 C Hourglass Basin Taps Instruction Manual
- June 13, 2024
- BRISTAN
Table of Contents
BRISTAN HOU 1-2 C Hourglass Basin Taps
Product Information
The product is a tap with dynamic water pressure capabilities. It has a minimum water pressure requirement of 0.2 bar and a maximum water pressure capacity of 5.0 bar. The tap is designed to withstand a maximum static pressure of 10.0 bar. It comes with two tap bodies, a coin-slot aerator, rubber washers, metal backnuts, and various tools required for installation and maintenance.
Specifications:
- Inlet Water Temperature: HOU 1/2 C (D6)
- Inlet Connections: 2.0 – 3.0
- Outlet Connections: 1.0 – 4.0
Pack Contents:
- x2 Tap Bodies
- M24 Coin-Slot Aerator
- x2 Rubber Washers
- x2 Metal Backnuts
- Tools Required for Installation/Maintenance: 24mm Socket Adjustable Spanner, 17mm Box Spanner, Spanner, Pipe Cutters, 2mm Hex Key, Crosshead Screwdriver
Prior to Installation:
- Ensure that the product is installed, operated, and regularly maintained according to the provided instructions.
- Comply with The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014 for installation requirements.
- Fit isolation valves to the inlet water supplies for future maintenance convenience.
- Thoroughly flush the water supply before installing the product to remove any debris.
- Ensure full access is available for future maintenance and servicing.
- Do not modify the product as it will void the guarantee.
Spare Parts:
To replace any spare parts for your tap, you can scan the QR Code or visit
www.bristan.com and search for your product.
Specifications
Pack Contents
Operation
Tools Required for Installation/ Maintenance
Prior to Installation
All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014. For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.co.uk/approvals-directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance. Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc. Full access must be made available for future maintenance/servicing purposes. This product must not be modified in any way as this will invalidate the guarantee.
Spare Parts
To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product.
IMPORTANT : Images shown are for illustrative purposes only.
The tap you have purchased may look different to those pictured in these instructions, but will follow the same installation steps.
Your contents page will be specific to your product. If you find your product or any of it’s components differ from those shown on the contents page, please contact our Customer Support on – 0330 026 6273
Instllation
Feed the tap body through the bath/basin and ensure plinth and plinth seals are in place. Your taps may come with plinths and will either be included pre-attached or loose in the box
-
You may be required to secure the plinth to the tap with a grub screw
- If the hole is not directly visible on the plinth, check underneath rubber seal
- Ensure rubber seal is in place once plinth is attached
-
Secure the taps to the basin/bath by using the washer and metal backnut below the basin/bath.
-
Connect the hot and cold water supplies to the threaded tails.
REMEMBER : To fit isolation valves for maintenance purposes -
IMPORTANT : Turn on water supply for a few minutes and check all joints and connections for any leaks.
Maintenance
Valve Replacement
PLEASE NOTE: Taps shown in these instructions are for illustration purposes only. All taps can be maintained using these instructions.
- Remove the handles depending on the style of your tap, including any spline adaptors if used.
- Unscrew handle washer to remove the handles.
- Remove the valve using the tool required for your tap. Check any seals and O-rings for damage. Replace valve if necessary.
- Take care when removing/replacing your long stemmed valve, as the finish could be damaged or scratched.
- Visit www.bristan.com or scan the QR Code and search for your product code to replace the cartridge for your tap.
- Reverse the steps to replace the valves and handles.
Maintenance Clean/Replace Outlet
PLEASE NOTE: Taps shown in these instructions are for illustration purposes only. All Taps can be maintained using these instructions.
-
Housed Outlet
Using an adjustable spanner, unscrew ently to remove the outlet- Recessed Outlet
- If provided, insert the key tool into the outlet and twist to release it
- Coin Slot Outlet
- Using a coin, insert into the slot on the outlet and twist to release it
- Fixed Outlet
- Using long- nosed pliers, unscrew gently to remove the outlet.
-
Check all loose parts for any damage, then soak using a suitable solution to de-scale
-
Reverse the steps to replace the outlet
Troubleshooting
General Cleaning
Bristan products are made from premium materials, with hand polished,
electroplated, PVD or EPD finishes.
Your taps should be regularly cleaned with warm water, a mild pH-neutral liquid soap and polished with a soft cloth. Any residues from soap, toothpaste etc. can cause blemishes if not rinsed off straight after use. Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
CONTACT US
Bristan Group Ltd. UK : Bristan Group, B78 lSG. EU : Masco Europe
S.a.r.l. 14 Rue Strachen 6933 Mensdorf Luxembourg
- Customer Service: +44330 026 6273
- Web: www.bristan.com
- Email: enquire@bristan.com
A Masco Company
Our Guarantee
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offersolid guarantees on all our products, effective from the
date of purchase, to give you peace of mind. To start your free guarantee
simply scan the QR code and register your product. Alternatively visit
wwwbristan.com/register. For any other queries, please call our Customer
Service on 0330 026 6273 where our expert team of advisors will be able to
offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service- centre/guarantees.