ASTATIC 575M-6 CB Ham Mic Microphone User Guide
- June 13, 2024
- ASTATIC
Table of Contents
ASTATIC 575M-6 CB Ham Mic Microphone User Guide
ASTATIC Quality
All575M-6 microphones are audio tested and inspected prior Lo shipment.
Our absolute commitinent Lo quality insures that ASTATIC microphones remain
the Best Value in today’s competitive industry.
Description
The ASTATIC 575M-G “power” microphonic offers the CB’ er modern “teardrop” styling und features along with the sound and “talk-power” mads famous by the ASTATIC D104 for over 60 years.
An output impedance compatible with the inputs of almost all commercial transceivers and externally adjustable high gain amplifier ensures desired modulation level, The 575M-6 has easily accessible stride controls for volume and tone adjustment so thali the correct modulation level and tone quality can be sel for cache operators voice. The §75M-6 preamplifier is powered by a readily available, casily replaced, 9 volt butlery. The 575M-6 has a six wire coil cord which allows for relay, electronic or virtually any type hookup with almost any transceiver. The studio ling is aspen during receive.
Specifications
Type:
Frequency Respanse : Transistorized Ceramic
Maximum Output Level : Adjustable (Sec Frequency Response Curve on other
side}38 dB below 1 volt per microbar at 1 kef into | megaohm load
Output Adjustment: ……….. 40 dB minimum range
Impedance :………………… 5000 ohms max., recommended load of 100 ohms and up;
performs well over entire
Connector ………………………. impedance range up to open circuit Available
stripped and tinned or configured with 4 pin (DX) or 5 pin (DX2) DIN.
Cable :…. Five conductor (one conductor shielded) culled cord that
extends to 2.3 m (7 1/2 A.).
Durable strain relief bushing protects against cable breakage at microphone
housing.
Housing:… Attractive, durable high impact molded black ABS
Battery : Standard 9 Volt Battery (Not Included)
Life……. Approximately 6 months (based on normal usage)
Size: 100 mm (3 15/16″) high x 75.4 mm (2 31/32″) wide x 54.8 mm (2
5/32″) deep 227 grams (8 oz.)
Weight:…… 227 grams (X 02}
Connector-Cable Clamping
If the microphone plug you have selected for your hookup requirements does not
have a cable clamp suitable for our small diameter high quality microphone
cable, use tubing as supplied by ASTATIC. Simply slip tubing over cable prior
to soldering of lead wires. Position it to ensure proper clamping of cable and
tubing by the connector.
SPECIFICATIONS FOR 575M-6B
Battery Replacement
Remove the rear housing by removing the four screws. Carefully lift off he
reur housing. Unsnap the batlery from (he battery connector and install a new
battery. Carefully replace the rear housing and fasten with The four screws
previously removed. Depress the switeh lever fully while tightcning the
screws.
Volume and Tone Adjustments
At a speaking distance of approximately 2 inches (or the position you preter)
with the external volume control set at ) and the tone control set in the
center position, wdjust the volume control for the correet modulation level,
Sliding the volume control toward 9 increases the volume. The externil tone
control should then be adjusted for the most intelligible saund. Slide the
tone control taward 0 for an increase in bass response and towards 9 for u
decrease in bass response.
![Volume and Tone
Adjustments](https://manuals.plus/wp- content/uploads/2023/09/Screenshot_4-864.png)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>