SMARTECH LBT-1.DO5 Bluetooth Mesh Triac Output Module User Manual
- June 12, 2024
- SMARTECH
Table of Contents
SMARTECH LBT-1.DO5 Bluetooth Mesh Triac Output Module User Manual
Written by SMARTEH d.o.o. Copyright © 2023, SMARTEH d.o.o. User Manual Document Version: 2 May 2023
Longo Bluetooth Products LBT-1.DO5
⚠⚠ STANDARDS AND PROVISIONS: Standards, recommendations, regulations and
provisions of the country in which the devices will operate, must be
considered while planning and setting up electrical devices. Work on 100 ..
240 V AC network is allowed for authorized personnel only.
DANGER WARNINGS: Devices or modules must be protected from moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITIONS: For all modules LBT-1 if no modifications are performed upon and are correctly connected by authorized personnel in consideration of maximum allowed connecting power, warranty of 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are based on material malfunctions the producer offers free replacement. The method of return of malfunctioned module, together with description, can be arranged with our authorized representative. Warranty does not include damage due to transport or because of unconsidered corresponding regulations of the country, where the module is installed. This device must be connected properly by the provided connection scheme in this manual. Misconnections may result in device damage, fire or personal injury. Hazardous voltage in the device can cause electric shock and may result in personal injury or death. NEVER SERVICE THIS PRODUCT YOURSELF! This device must not be installed in the systems critical for life (e.g. medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer, the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected separately!
LBT-1 devices are developed considering the following standards:
- EMC: EN 303 446-1
- LVD: EN 60669-2-1
Smarteh d.o.o. operates a policy of continuous development. Therefore we
reserve the right to make changes and improvements to any of the products
described in this manual without any prior notice.
MANUFACTURER: SMARTEH d.o.o. Poljubinj 114 5220 Tolmin Slovenia
1. ABBREVIATIONS
LED Light Emitted Diode
PLC Programmable Logic Controller
PC Personal Computer
OpCode Message Option Code
2. DESCRIPTION
LBT-1.DO5 Bluetooth Mesh triac output module is designed to be used as a triac digital output module with RMS current and voltage measuring possibility. The module can operate with a wide range of AC voltages. It can be placed inside the 60mm diameter flush mounting box. It can also be placed inside the lights, inside various electrical equipment and devices to switch On and Off their power supply voltage.
LBT-1.DO5 Bluetooth Mesh triac output module can also be connected close to the light in the traditional electrical wiring 115/230 VAC for lightning. Light connected to the LBT-1.DO5 triac can be switched on and off with existing light switches. The module can detect power supply input voltage drop when the switch is pressed. Wire bridge on the last switch before the LBT-1.DO5 triac module should be wired as shown in Figure 4. While LBT-1.DO5 is a Bluetooth Mesh module the triac output can be also switched On and Off by using Bluetooth Mesh communication. At the same time, triac RMS current and voltage can be sent over the Bluetooth Mesh communication.
LBT-1.DO5 Bluetooth Mesh triac output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway connected to the same Bluetooth Mesh network. LBT-1.GWx Modbus RTU gateway is connected to the main control device as Smarteh LPC-3.GOT.012 7″ PLC based Touch panel, any other PLC or any PC with Modbus RTU communication. Besides Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh devices can be integrated into above mentioned Bluetooth Mesh network. More than a hundred Bluetooth Mesh devices can be provisioned and can operate in a single Bluetooth Mesh network.
3. FEATURES
4. OPERATION
LBT-1.DO5 Bluetooth Mesh Triac output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway while provisioned to the same Bluetooth Mesh network.
4.1. Other triac output module functions
- Factory reset: This function will delete all Bluetooth Mesh network parameters stored on LBT-1.DO5 triac output module and will restore to the conditions of the initial programming, ready for provisioning. See Table 5 for more information.
4.2. Operation parameters
LBT-1.DO5 Bluetooth Mesh Triac output module accepts a set of operation codes as specified in below tables 2 to 4. LBT-1.DO5 Bluetooth Mesh triac output module is communicating with main control device as Smarteh LPC-3.GOT.012 via Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway. All communication between main control device as LPC-3.GOT.012 or similar is performed by using Modbus RTU communication. Individual Bluetooth Mesh node configuration data should be observed by using network provisioning tool.
- Observed from network provisioning tool
** User defined parameters, refer to option code table
5. INSTALLATION
5.1. Connection scheme
5.2. Mounting instructions
- Switching Off the main power supply.
- Mount the module up to the provided place and wire the module according to the connection scheme in Figure 4. When you connect the module to the traditional electrical wiring for lighting please be sure, that you wired the bridge on the last switch before the LBT-1.DO5 module as shown in Figure 4.
- Switching On the main power supply.
- After a few seconds Green or Red LED starts to blink, please see the flowchart above for details.
- If the module is not provisioned Red LED will blink 3x, the provisioning procedure has to be started. Contact the producer for more details*.
- Once provisioning is finished, the module will continue with the normal mode of operation and this will be indicated as Green LED blinking once per 10 seconds. Dismount in reverse order.
*NOTE: Smarteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by using standard provisioning and configuration mobile apps tool such as nRF Mesh or similar. Please contact producer for more detail information.
6.SYSTEM OPERATION
LBT-1.DO5 Bluetooth Mesh triac output module can switch power to the output load based on power supply voltage drop pulse, based on switch input voltage change or based on Bluetooth Mash command.
6.1. Interference warning
Common sources of unwanted interference are devices that generate high
frequency signals. These are typically computers, audio and video systems,
electronics transformers, power supplies and various ballasts. The distance of
the LBT-1.DO5 triac output module to the above mentioned devices should be at
least 0.5m or greater.
WARNING:
- In order to protect plants, systems, machines and network against cyber threats, necessary to implement and continuously maintain up to date security concept.
- You are responsible for preventing unauthorized access to your plants, systems, machines and networks and they are allowed to be connected to Internet only, when security measures like firewalls, network segmentation, … are in place.
- We strongly recommend the updates and usage of latest version. Usage of version that are no longer supported may increase the possibility of cyber threats.
7.TECHNICAL SPECIFICATIONS
8.MODULE LABELING
Label description:
-
XXX-N.ZZZ – full product name,
• XXX-N – product family,
• ZZZ.UUU – product, -
P/N: AAABBBCCDDDEEE – part number,
• AAA – general code for product family,
• BBB – short product name,
• CCDDD – sequence code,
• CC – year of code opening,
• DDD – derivation code,
• EEE – version code (reserved for future HW and/or SW firmware upgrades), -
S/N: SSS-RR-YYXXXXXXXXX – serial number,
• SSS – short product name,
• RR – user code (test procedure, e.g. Smarteh person xxx),
• YY – year,
• XXXXXXXXX – current stack number, -
D/C: WW/YY – date code,
• WW – week and,
• YY – year of production.
Optional:
• MAC,
• Symbols,
• WAMP,
• Other.
9. CHANGES
The following table describes all the changes to the document.
