GVM GT60 24 Inch Track Dolly Slider Rail System Instruction Manual

Instruction Manual GT-60D
24 Inch Track Dolly Slider Rail System

Packing list

Mounting the camera on the slider

1. Please charge the battery before use the product.
2. Please install the battery on the controller as shown in the picture. (As shown below)
3. Connect the controller and slider as shown in the following pictures. (As shown below)
4. Mounting the camera on the slider. (As shown below)
5. Time-Lapse photography connect method :
   1）After finished above steps, take out the shutter release cable and extension cable. ( The cables need to be purchased separately ) 2) Insert the cable into the controller’s shutter release cable interface (use the extension cable if needed) . Connect the other side to the camera shutter release cable interface. (As following pictures show)

Settings Menu

1. Turn off power to reset the remote control.

2. Settings Menu
   1/ Set the Language:
   1. Press the up or down arrow and highlight the Language menu option (P1).
   2. Press the right or left arrow button to change language between English and Chinese. Long press the middle button to save your settings. 2/Set the start point:
   1. Press the up or down arrow and highlight the Settings menu option (P2).
   2. Press the middle button.
   3. Highlight the Set Start option and press the middle button (P3). 4. Press the right or left arrow button to move the slider. Press the middle button to stop the motion.
   5. Press the middle button a second time to select the start point (P4)
   6. Long press the middle button to save the start point. 3/Set the end point:
   1. Highlight the Set End option and press the middle button (P5)
   2. Press the right or left arrow button to move the slider. Press the middle button to stop the motion.
   3. Press the middle button a second time to select the end point (P6)
   4. Long press the middle button to save the end point. 4/Set the speed:
   1. At any time while setting the start or end points, you can adjust the speed from [1100%] by pressing the Up or Down arrows (P4), (P6). 5/ Reset:
   1.Highlight the Reset option(P7).
   2.Press the right r left arrow button to choose “Yes”or”No”.Press the middle button to reset the remote control or go back setting menu.
   3.Long press the middle button to save the setting.

3. Time lapse menu
   1/ Set the start point:
   1. Press the up or down arrow and highlight the Time Lapse menu option (P8).
   2. Press the middle button.
   3. Highlight the parameter you want to change and adjust its value by pressing the right or left arrow button (P9).
   4. Press the middle button when complete.
   5. Press the right or left arrow button to begin time lapse shooting.
   6. Press the middle button to pause any motion.7. “Interval” means the slider moving time, the time unitis “seconds”.
   8. “Time-lapse” means the camera shutter shot time after stop moving, the time unit is “seconds”.
   9. “Stop time” means the time interval between the slider’s two movements, the time unit is “seconds”.
   10. The minimum Interval time is 0.1 second, the minimum Time-lapse time is 0.1 second, the minimum stop time is 1 second. Note: the Stop Time needs longer than the Time-lapse time at least 0.2 seconds.

4. Video shot menu
   1/ Manual Mode:
   1. Press the up or down arrow and highlight the Video Shot menu option (P10) and then press the middle button.
   2. Highlight Manual Mode and then press the middle button(P11)3. Press the left or right arrow button to begin motion (P12).
   4. You can adjust the speed at any time by pressing the Up or Down arrow buttons.

5. Auto Mode
   Auto Mode has two options: Auto Loop and Auto Stop.
   To use either one, you first must set the start and end points as described in the Settings section.
   1. Press the up or down arrow and highlight the Video Shot menu option. Then press the middle button.
   2. Press the up or down arrow buttons and highlight the Auto Mode menu option (P13). 1/Auto Loop will provide motion between the start and end points indefinitely.
   1. Highlight the Auto Loop button and then press the middle button (P14).
   2. Press the right or left arrow to start motion.
   3. Press the middle button to pause the motion.
   2/ Auto Stop will provide motion between the start and end points one time.
   1. Highlight the Auto Stop button and then press the middle button (P15).
   2. Press the right or left arrow to start motion.
   3. Press the middle button to pause the motion.

TROUBLE SHOOTING

1. Use a standard Sony NP-F550/F570/F770/F9XX series battery.
2. Monitor the battery power level shown on the bottom of the remote controller.
3. Make sure all cables are firmly inserted into all devices.
4. If the slider is not horizontal, make sure to lock the center brake before turning off the power or disconnecting the cable. Under normal operations, the motor acts as a break and any loss of power will permit the camera base to quickly fall to its lowest point potentially damaging your camera or slider.

Huizhou City Latu Photographic Equipment Co., Ltd.
Web: www.gvmled.com
B&H Email: bh@gvmled.com
GVM Email: support@gvmled.com
Amazon Email: amazonsupport@gvmled.com
Warehouse Add: 4301 N Delaware ave, unit D. PHILADELPHIA, PA19137, USA

References

• GVM Lights Official Store - Great Video Maker - Video Lights

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>