KAISDA K6-Electric-Bike User Manual

June 3, 2024
KAISDA

E-bike User’s Manual

Safety Instruction

  1. Thank you for purchasing the KAISDA E-BIKE. The E-BIKE features the most recent innovation in technology.
  2. For Safety reasons, it is most important that you read this user’s manual before you operate the bike. Improper handling can reduce its riding performance and most importantly, cause danger to your safe and healthy.
  3. For handling and maintenance of the bicycle, please refer to the E-BIKE user’s manual which is an integral part of this e-bike user’s manual!
  4. Do not at any time dismantle or disassemble any of the above e-bike components!
  5. Please check all parts are tighten and locked before riding.
  6. Please make sure that the battery charger and charging plug are always kept dray and never get wet.
  7. The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or any other liquid.

Instruction

Meter operation

3.1 Meter instruction
3.2 Meter operation

3.2.1: Hold the button ** for 2s to switch on/off the E-Bike system. The default value is “low” pedal assist level. Full Electric Function (Pure electric mode)
3.2.2: Press “+” to crease into pedal assist level “Mid”. Full Electric Function (Pure electric mode).
3.2.3: Press “+” again to move into pedal assist level “High”. “High” is the maximum power of PAS. Full Electric Function (Pure electric mode)
3.2.4: Foot riding (without pedal assistant and electric)
3.2.5: Press the “+” button for 2 seconds during power-on state, the system defaults to turning on the front light. When the front light is on, press the “+” button for 2 seconds, the system defaults to turn off the front light.
3.3 Meter Solution Instruction:**

  1. The following steps keep the meter operated in the power off state;
  2. Keep the brake and throttle working at the same time, then turn on the meter for 5-7 seconds and release the brake handle and throttle to release the speed limit;
  3. If you want to restore the factory configuration after the speed limit is lifted, repeat the above 1.2. operation.
    ( For more detailed answers please contact customer service personnel to remove the speed limit video)

3.4 Operation Cautions
Be careful of the safety use. Don’t attempt to release the connector when charging the battery.

  • Avoid the risk of collision.
  • Don’t modify system parameters to avoid parameters disorder.
  • Make the display repaired when error code appears.

Battery: further information and maintenance

  1. How far full charge battery can go? That depends on the loading weight, road condition and battery capacity. But in the same condition, average speeds can continuous longer travel range.
  2. When storing the battery for a longer time period, (e.g. during winter time) it is important to place the fully charged battery on a flat surface in a dry place.
  3. Attention: The battery should be re-charged once every 2-3 month when it is not used.
  4. Warning:
    4.1. Keep the battery out of reach for children.
    4.2. Never try to open the battery.
    4.3. If the battery is damaged because it has been dropped somewhere or because of a biking accident, there might be a risk of electrolytes leakage.
    Beware of chemical burns! And immediately stop using a damaged battery.
    4.4 Do not touch the battery without a cloth or gloves and make sure no acid touches your eyes.

Charging

  1. To charge the battery with the bike, simply place the bike within reach of the power supply and plug it in. Note: The plug hole is located in the left of the battery.
  2. The battery can either be charged while on the bike or the battery can be removed and charged at a place of your convenience.
  3. The RED light indicates it is in charging and GREEN light indicates the battery is fully charged. (Please put off plug from wall) Usually the charging time is 4-6 hours depends on the battery capacity remain.
  4. Warning: Charging time over 10 hours is prohibited please kept it away from high temperature environment and stores it in a cool place.

Installation Instruction

  1. Open the carton, take our the e-bike, and cut the wrapping rope with tools.

  2. Handlebar installation:
    2.1 Insert the seat tube vertically and align it with the frame head tube.
    The depth must exceed the minimum insertion depth marked on the seat tube.
    2.2 Align the standpipe so that the handlebar and the frame are at 90 degrees, and then use an M6 hexagon wrench to tighten the mounting screws on the standpipe.
    2.3 Adjust the correct position of the handlebar, and then use tools to lock the handlebar cover.

  3. Headlight installation:
    3.1 Loosen the headlight screw from the front fork; install the headlight and the front fender ears in the front fork screw hole, and tighten the screw with an Allen tool.

  4. Front wheel installation:
    4.1 Cut the wrapping rope, remove the front wheel, remove the front fork protection lever and the front wheel protection cover.
    4.2 Make sure that the front wheel is in line with the rear wheel, then start installation. First pull the wheel upwards, put the disc brake pad into the front brake caliper, and then use 15 wrench to tighter the front hub fixing screw, and then use tool to lock the mud board supporter on the front fork leg.
    4.3 Adjust the adjusting screw of the disc brake to make the disc brake rotor without obvious friction

  5. Bicycle Rack installation:
    5.1 First align the mounting holes of the rack with the mounting holes on the frame, and then use an M4 hexagon wrench to tighten the mounting screws of the rack respectively.

  6. Foot pedal installation:
    Check the two pedals. The pedal with “L” printed on the end of the mandrel should be installed on the left side of the vehicle (without chain ring), rotate counterclockwise, and the “R” pedal should be installed on the right side. (With chain ring), rotate clockwise, and then use a No. 15 wrench Tighten the pedal spindle.

  7. Saddle installation:
    7.1 Open the package and take out the seat saddle and seat post. Install the rear reflector on the seat post.
    7.2 Insert the seat post into the frame.
    7.3 Adjust the seat position to the height that best suits your riding position, and tighten the quick release (please ensure that the quick release is locked)

  8. Adjust the brakes, meters and transmissions system, and then tighten them with tools.

  9. Tire inflation instruction
    9.1 After the bicycle is assembled, please check whether the air pressure of the front and rear tires is within the normal value.
    9.2 When refilling tires, you must refer to the inflation reference range on the side of the tire for refilling, generally between 35PSI—65PSI (280Kpa–450Kpa).

  10. Instructions for using Front derailleur
    10.1 When you shift forward the right derailleur handle, the back derailleur will move inside, at the same time, move the chain from the small part of the rear flywheel to the large part. These steps will reduce the riding speed while riding, also will reduce the pedaling strength of riding. When the handle bar at the maximum position(as shown in picture 3 below), press the accelerator button on the right derailleur handle, the back derailleur will move outward, at the same time, move the chain from the large part of the rear flywheel to the small part. These steps will increase the riding speed while riding, also will increase the pedaling strength of riding.So as to realize the different speed of the back derailleur.

More KAISDA electric bike’s installation question and repair question about the item, please contact.

Detail Packing List

Description| Quantity
E-Bike| 1
Tools (13-15 spanner, 9-11, 8-10,14-17 spanner, eleven-shaped screwdriver,
M6, M5, M4, M3 Allen wrench)| 1
Manual| 1
Key| 2
Charger| 1
Front Fender| 1
Pedal| 1
Saddle| 1
Seat tube| 1
Rear Rack| 1

CAUTION READ THIS MANUAL BEFORE USING YOUR EQUIPMENT

Information about the manufacturer

Manufacturer:| Guangzhou City KAISDA Technology Co.,Ltd
Address:| Room 1027, Liantang Business Plaza, 195 Commercial Avenue, Huadu District, Guangzhou
Information about the product
Model No.:| K6
Marke:| KAISDA
EC REP Information for EU representatives
Name:| EUREP GmbH
Address:| Unterlettenweg la, 85051 Ingolstadt,Germany
Telephone:| 4984188697744
E-mall:| eurep@eurep-gmbh.com
Made in China

Documents / Resources

| KAISDA K6-Electric- Bike [pdf] User Manual
K6-Electric-Bike
---|---

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals