HAMPTON BAY HDP00330 Stratton 10 Light Chandelier User Guide
- June 4, 2024
- HAMPTON BAY
Table of Contents
HAMPTON BAY HDP00330 Stratton 10 Light Chandelier
Safety Information
Consult a qualified electrician with any electrical questions you may have.
IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue the assembly process. Please call our Customer Service Team at 1-855-HD-HAMPTON.
Warranty
3-YEAR LIMITED WARRANTY
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in the
materials and workmanship for a period of three (3) years from date of
purchase. This warranty applies only to the original consumer purchaser and
only to products used in normal use. If this product is found to be defective,
the manufacturer’s only obligation, and your exclusive remedy, is the repair
or replacement of the product at the manufacturer’s discretion, provided that
the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not
apply to any product that is found to have been improperly installed,
assembled, or used in any way not in accordance with the instructions supplied
with the product. This warranty shall not apply to a failure of the product as
a result of an accident, misuse, abuse, negligence, alteration, faulty
installation, or any other failure not relating to faulty material or
workmanship.
WHAT IS NOT COVERED
This warranty shall not apply to the finish on any portion of the product due
to weathering, as this is considered normal wear. The manufacturer does not
warrant and specifically disclaims any warranty, whether expressed or implied,
other than the warranty contained herein. The manufacturer specifically
disclaims any liability and shall not be liable for any consequential or
incidental loss or damage, including but not limited to, any labor or expense
costs involved in the replacement or repair of the product.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit
www.HamptonBay.com.
Pre-Installation
PLANNING INSTALLATION
Read all instructions before assembly. To avoid damaging this product,
assemble it on a soft, non-abrasive surface such as carpet or cardboard.
Inspect each part for defects that may have occurred during shipping. Keep
your receipt and these instructions for proof of purchase.
NOTE: This light fixture requires the use of ten 120V, 60Hz, 60- Watt max., medium-base type S21 (ST64) bulbs (included). Do not exceed the recommended wattage.
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Wire nut | 3 |
| BB | Cross bar | 1 |
| CC | Outlet box screw | 2 |
| DD | Lock nut | 2 |
| EE | Ground screw | 1 |
| FF | Nipple | 1 |
| GG | Canopy | 1 |
| HH | Screw collar loop | 1 |
| II | Screw collar nut | 1 |
| JJ | Chain | 1 |
| KK | Quick link | 2 |
| Part | Description | Quantity |
|---|---|---|
| A | Chain loop | 1 |
| B | Column assembly | 1 |
| C | Arm | 5 |
| D | Fixture body | 1 |
| E | Bulb | 10 |
Assembly
Assembling the light fixture
- Carefully unpack the fixture and lay out all parts on a clean surface.
- This fixture can be assembled up or down. Screw the chain loop (A) to the top of the column assembly (B).
- Attach the hooks of the arms (C) to the loops of the column assembly (B).
- Attach the other hooks of the arms (C) to the loops of the figure body (D).
Preparing the light fixture to hang
- Attach the quick link (KK) to one end link of chain (JJ) and attach the quick link (KK) to the chain loop (A).
- Remove chain links from the chain (JJ) in order to achieve the desired length for hanging the light fixture.
- Thread the fixture and ground wires up through every link in the chain (JJ).
To open the chain link: Use a pair of pliers and a screwdriver as shown above to open a chain link. Wrap the jaws of the pliers with cloth to protect the finish.
Installation
Installing the cross bar
- Turn off the switch at the wall.
- Turn the power off at the main fuse box.
- Install the cross bar (BB) with nipple (FF), lock nuts (DD), and screw collar loop (HH) to the outlet box using two outlet box screws (CC).
- Unscrew the screw collar nut (II) from the screw collar loop (HH).
- Slide the screw collar nut (II) and then the canopy (GG) onto the end of the chain (JJ).
- Attach the quick link (KK) to the end of the chain (JJ) and attach the quick link (KK) to the screw collar loop (HH).
- Insert the fixture wires up through the nipple (FF).
Connecting the wires
- Install the fixture bare copper ground wire (1) under the ground screw (EE) on the cross bar (BB).
- Connect the fixture bare copper ground wire (1) to the green (or bare, or green & yellow) supply ground wire (2) in the outlet box using a wire nut (AA).
- Connect the ribbed fixture wire (3) to the white supply wire (4) in the outlet box using a wire nut (AA).
- Connect the smooth fixture wire (5) to the black (or red, or blue) supply wire (6) in the outlet box using a wire nut (AA).
Hanging the light fixture
- Push all excess wires into the outlet box.
- Raise the canopy (GG) to the ceiling and secure in place by screwing the screw collar nut (II) onto the screw collar loop (HH).
Installing the bulbs
- Prior to installing the bulbs, inspect sockets for silica packets. If packets are present, then remove and throw away. Do not expose to children or pets.
- Install ten 120V, 60Hz, 60-Watt medium-base type S21 (ST64) bulbs (E) (included) into the sockets of the light fixture.
Care and Cleaning
Clean the light fixture with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The bulb will not light. | □ The bulb is burned out. | □ Replace the light bulb. |
| □ The power is off. | □ Ensure that the power supply is turned on. | |
| □ There is a faulty wire connection. | □ Check the wiring. | |
| □ The circuit breaker is off. | □ Ensure that the circuit breaker is set in the |
on position.
The fuse blows or a circuit breaker trips when the light is turned on.| □
There is an exposed wire.
□ There are too many items on one circuit.
| □ Discontinue use of the light fixtur .
□ Contact a qualified electrician or call the Customer Service Team at 1-855-HD-HAMPTON.
□ Unplug other items on the circuit.
Questions, problems, missing parts? Before returning to the store, call
Hampton Bay Customer Service 8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. –
6 p.m., EST, Saturday
1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual
for future use.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>