UPLIFT DESK FRM682 V2-Commercial 4-Leg Standing Desk Foot Instruction Manual

: June 4, 2024
: UPLIFT DESK

Table of Contents

Package Contents
Recommended Assembly Workspace & Practices
Reset Procedure
**** CAUTIONS & WARNINGS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FRM682 V2-Commercial 4-Leg Standing Desk Foot
Instruction Manual

Package Contents

UPLIFT DESK FRM682 V2-Commercial 4-Leg Standing Desk
Foot

Recommended Assembly Workspace & Practices

Place all parts on a clean surface such as a rug or carpet to avoid scratches.
Two or more people are recommended for assembly.
Remove all packaging materials, before beginning the assembly process.

Step 1
A. Remove all objects, accessories, and attached components from the desk since you will be inverting them for this installation.
B. Press and hold the Down Button to bring the desk to its lowest position, then unplug the desk from the electrical outlet.
C. Prior to flipping the desk over, move it to a suitable area free from clutter or obstruction. We recommend resting the desktop on a carpet or blanket.
Be aware of any cables or attached components and secure them before flipping the desk.

Note: When flipping the desk, always hold the frame and the desktop together. Lifting by the desktop only could put stress on improperly fastened screws connecting the desktop to the frame and may cause them to separate from the frame if they were not attached properly.

D. You and a friend should each hold on to the rear edge of the desktop with one hand and hold a leg with the other hand.
E. Supporting both the desk frame and the desktop, slowly tilt the desktop toward the rear of the desk until the back edge of the desktop is resting on the ground.
F. Hold onto the leg and the front edge of the desktop, then tilt the desk another 90 degrees until the desk is upside down and resting on a carpet or blanket. UPLIFT DESK FRM682 V2-Commercial 4-Leg Standing Desk Foot - Step
1

Step 2
A. If your desk has casters installed and you plan to use them with the new Feet, remove them from each of the currently installed peg feet. You may need a 0.5” (13mm) flat wrench or thin adjustable crescent wrench to remove the casters.
B. Using the included 4mm Allen Wrench, remove each of the M6x14 Machine Screws that are holding the peg feet to the legs (four screws per peg foot).

Step 3
A. Place one of the new Feet on top of two legs on one side of the desk, as shown, with the pre-installed leveling glides facing up. Each leg should fit inside the rectangular holes in the foot.
B. Insert, but do not tighten, an M6x14mm Machine Screw into each of the eight threaded holes.

Note: If you are having difficulty aligning the holes in the Foot with the holes in the legs, use the 4mm Allen Wrench to loosen, WITHOUT REMOVING, the four screws that attach each leg to the crossbar ends. Be sure to firmly tighten these screws again once the Foot has been fastened to the legs.

C. Once all eight screws have been started, tighten them with the 4mm Allen Wrench.
D. Repeat the previous steps for the second new Foot.
E. The desk frame screws can become loose over time or may not have been completely tightened during the initial assembly. Since the desk is upside down, take the opportunity to ensure all frame screws are tight using the 4mm, Allen Wrench.

UPLIFT DESK FRM682 V2-Commercial 4-Leg Standing Desk Foot - Step
3

Step 4
A. If you are replacing casters removed in Step 2, first remove the pre- installed leveling glides by unscrewing them, no tool necessary.
B. Thread the casters into the Feet and use a 0.5” (12mm) flat wrench to tighten each caster.
C. Ensure the casters are in the locked position before flipping your desk upright again to ensure the desk does not move as you flip it onto the casters. To lock the casters, flip the lever at the back of each caster to the down position (towards the ceiling when the desk is upside down) and test the wheel to make sure it does not turn.

Step 5
A. With the help of a friend, flip the desk upright. Refer to Step 1 and reverse those instructions.
B. Move the desk back to its location.

If you have casters installed, make sure the casters are not locked and roll them to the location.
If you are using the pre-installed leveling glides, carefully lift the desk with two or more people and move it to its location – DO NOT drag the desk as this may cause damage to the desk and floor.

C. Once the desk is in position, reinstall any accessories that had been removed and plug the power cord back into the outlet.
D. Before use, perform the reset procedure below.
This is an important step. UPLIFT DESK FRM682 V2-Commercial 4-Leg Standing
Desk Foot - Step 5

Reset Procedure

Before using the desk, you must first perform this Reset Procedure:

Press and hold the Down Button until the desk stops at its lowest position, then release.
Note: On the Advance Paddle keypad, press down on the paddle.
Press and hold the down button again for 30 seconds, then release.
Note : On the Advance Paddle keypad, the word “RESET” will appear at this point.
Note: On other UPLIFT keypads with display, the letters “ASr” will appear at this point.
Press and hold the Down Button one more time until the desk lowers slightly, rises and stops, then release the button. The reset is complete and the desk is ready for use.

**** CAUTIONS & WARNINGS

CAUTION : Read all instructions before assembly. Failure to assemble or operate properly may result in damage or personal injury. Retain manual for future reference.
WARNING : Make sure that the wires for your monitor and devices are not touching any obstacles or walls and are an appropriate length to allow for full adjustment of the desk. Make sure that no obstacles are in the full range of height adjustment.
WARNING : Designed for use in dry work environments only. Risk of fire, electric shock, or personal injury if used outdoors or in a damp location. Use only indoors.
WARNING : Only plug the desk into a properly grounded 120V outlet. Unplug the desk from the electrical outlet before moving the desk or before adding/removing parts or accessories. Risk of electric shock.
WARNING : Do not open any desk component or insert any object in a desk component. Risk of electric shock.
WARNING : In case of spilled liquids, immediately unplug desk. Then clean spill with a dry cloth.
Risk of desk failure or electric shock if desk components become wet.
WARNING : Keep heated surfaces away from plug. Never use the desk with a damaged cord or plug. Risk of electric shock. Call us for a free replacement cord.
WARNING : Keep fingers and all body parts clear of the moving desk. Check surroundings on all sides before using the desk to ensure there are no immobile obstacles within the desk’s range of motion. Ensure all cords are the appropriate length so they don’t pull as the desk moves.
WARNING : Keep unsupervised children away from the desk. Before use, teach children about desk safety with this manual. Risk of personal injury and electric shock if the desk is misused.
WARNING : This desk is height adjustable so that it may be positioned at a user’s ergonomic height as described in this manual. Inappropriate use of this desk can cause property damage or bodily injury. Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from improper use or handling of this desk. Provide this manual to any new user.
WARNING : When relocating the unit, remove all devices to avoid harm or damage, and adjust the unit to its lowest position.
WARNING : When relocating the unit, move it carefully with two people, to avoid injury and damage to the product and surroundings.
© Copyright Notice: These instructions are a component of this product. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior
written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.