SONY XS690GS 2 Way Speaker Instructions

SONY XS690GS 2 Way Speaker

Specifications

• Speaker Type: 2-Way Speaker
• Short-term Maximum Power: 420 W*2
• Rated Power: 50 W*2
• RMS Power (CTA 2031): 60 W
• Rated Impedance: 4 Ω
• Output Sound Pressure Level: Not specified
• Effective Frequency Range: Not specified
• Mass: Approximately 1,000 g (2 lb 3 oz) per speaker

Product Usage Instructions

Mounting

Before mounting the XS-690GS speaker, please follow these steps:

1. Ensure you have an appropriate mounting location. If you are unsure, consult your car dealer or nearest Sony dealer for guidance.
2. Gather the necessary materials: speaker cord (not supplied) and a power amplifier or similar device.
3. To release the cables, firmly push down on the catch and carefully release them. Avoid using excessive force to prevent damage to the speaker or cable terminals.

FAQ (Frequently Asked Questions)

Q: What is the short-term maximum power of the XS-690GS speaker?
A: The short-term maximum power of the XS-690GS speaker is 420 W*2.

Q: What is the rated power of the XS-690GS speaker?
A: The rated power of the XS-690GS speaker is 50 W*2.

Q: What is the RMS power of the XS-690GS speaker?
A: The RMS power of the XS-690GS speaker (CTA 2031) is 60 W.

Q: What is the rated impedance of the XS-690GS speaker?
A: The rated impedance of the XS-690GS speaker is 4 Ω.

Q: What is the mass of each XS-690GS speaker?
A: Each XS-690GS speaker has a mass of approximately 1,000 g (2 lb 3 oz).

Dimensions

• A. Reference Point
• B. Reference Plane
• C. Reference Axis

Precautions

• Do not continuously use the speaker system beyond the peak power handling capacity.
• Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers.
• Please note the following when installing the units; otherwise malfunction and/or deterioration in sound quality may result.
  • Do not touch the diaphragms and/or speaker cones by hand or with tools.
  • Do not put your fingers through the holes of the frame.
  • Do not drop foreign objects in the units.
• Do not place this product close to medical devices.
  • This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.

If you cannot find an appropriate mounting location, consult your car dealer or your nearest Sony dealer before mounting.

Specifications

• Speaker Coaxial 2 way:
  Woofer 16 cm × 24 cm (6 in × 9 in) cone type
  Tweeter 2.5 cm (1 in) dome type

• Short-term maximum power1 420 W2

• Rated power 50 W*2

• CTA 2031 RMS Power 60 W

• Rated impedance 4 Ω

• Output sound pressure level 90 dB ± 2 dB (1 W, 1 m)*2

• Effective frequency range 40 Hz – 24 000 Hz*2

• Mass Woofer: Approx. 1 000 g
  (2 lb 3 oz) per speaker

• Supplied accessories Parts for installation

Design and specifications are subject to change without notice.

1. “Short-term maximum power” may also be referred to as “Peak Power”.
2. Testing Condition: IEC 60268-5 (2003-05)

Mounting

Before mounting
A depth of at least 73 mm (2 7/8 in) is required for flush mounting. Measure the depth of the area where you are to mount the speaker, and ensure that the speaker is not obstructing any other components of the car. Keep the followings in mind when choosing a mounting location:

• Make sure that nothing is obstructing around the mounting location of the door (front or rear) or the rear tray where you are to mount the speaker.

• A hole for mounting may already be cut out of the inner panel of the door (front or rear) or the rear tray. In this case, you need to modify the board only.

• If you are to mount this speaker system in the door (front or rear), make sure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window mechanism in the door (when you open or close the window), etc.
  Also make sure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests, door pockets, lamps or seats etc.

• If you are to mount this speaker system in the rear tray, make sure that the speaker terminals, frame or magnet do not touch any inner parts of the car, such as the torsion bar springs (when you open or close the trunk lid), etc.
  Also make sure that the speaker grille does not touch any inner fittings, such as seat belts, head rests, center brake lights, inner covers of the rear wipers, curtains or air purifiers, etc.

Parts list

Mounting from the car interior

REAR TRAY

1. Mark the 4 bolt holes and make them 3.2 mm (5/32 in) in diameter.
2. Note
   When releasing the cables, push down on the catch firmly and release them carefully.
   If excessive force is used, damage to the speaker or cable terminals may result.

References

• Sony Corporation - Home

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>