ANKER 737 120W GaNPrime Power Bank User Manual
- June 13, 2024
- Anker
Table of Contents
ANKER 737 CHARGER
(GaNPrime 120W)
USER MANUAL
Attention
Read all the instructions before using the product.
- The product is designed for use with IT equipment only.
- Naked flame sources, such as candles, must not be placed on the product.
- The disconnection from line voltage is made by AC plug.
- In case of broken plugs, the product must be disposed of.
- If you want to clean the product, only use a dry cloth or brush.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- The power supply is not intended to be repaired by service personnel in case of failure or component defect (the product can be disposed of).
Using Your Product
For the fastest and safest charge, use an Anker® cable, your device’s original cable or another certified cable (such as MFi).
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference In a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However. there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
(4) Consult the dealer or an experienced radio/ TV technician for help.
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA
91764
Telephone: + 1 (800) 988 79733
This device complies with Industry Canada license-ICES-003.
Operation is subject to the following two conditions. (1) This device may not
cause interference. and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
IC Statement
This digital apparatus complies with CAN ICES-003(B)/NMB-003(B).
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Directive 2014/35/EU & 2014/30/EU & 2011 /65/EU & 2009/125/EC & 2019/1782/EU. The full text of the EU declaration of conformity is available at the following internet address. https://www.anker.com.
Hereby, Anker Innovations Limited declares that this product is in compliance with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016 & The Restrict on of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 & The Ecodesign for Energy-Related Products Regulations 2010. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com.
Indoor use only
This symbol indicates that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable collect on point for
the recycling of electrical and electronic equipment.
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
The following importer is the responsible party (contract for EU and UK
matters)
Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3, 80807 Munich,
Germany
Anker Technology (UK) Limited | GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Specifications
| Input | 100-240V~1.9A 50-60Hz |
|---|---|
| Output | Use One Port: |
Use 1 Port Output
USB-C1 (Top Port), USB-C2(Middle Port)
USB-C1 /USB-C2 :
5V ⎓ 3A /9V ⎓ 3A /15V ⎓ 3A /20V ⎓ 5A (100W Max)
USB-A:
4.5V⎓5A/5V⎓4.5A/5V⎓3A/9V⎓2A/
12V⎓ 1.5A (22.5W Max) Use Two Ports:
USB-C1+USB-C2 : 120W Max
USB-C1+USB-A : 120W Max
USB-C2+USB-A : 24W Max Use Three Ports:
USB-C1+USB-C2+USB-A : 120W MaxTotal Output : 120W Max
Average Active Efficiency| 85.18%
Efficiency at Low Load (10%)| 73.92%
No-Load Power Consumption| 0.23W
Recommended Operating Temperature| 0°C~ 25°C/32°F -77°F
Note: To ensure electrical safety and product performance, the output power
may fluctuate based on the ActiveShield™ 2.0* safety mechanism when the
ambient temperature is between 26-35°C (78.8-95°F) with a high output load.
*ActiveShield™ 2.0 enhances protection by intelligently monitoring temperature and adjusting power output to safeguard your connected devices.
Customer Service
24-month limited warranty*
*Please note that your rights under applicable law governing the sale of consumer goods remain unaffected by the warranties given in this Limited Warranty.
Lifetime technical support
support@anker.com
support.mea@anker.com (For Middle East and Africa
Only)
(US)+ 1 (800)988 7973 Mon-Fri 6.15 – 17:00 (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00-17:00; Sat-Sun 6:00-14:00
(DE) +49 (0) 69 9579 7960 Mo-Fr 6:00 – 11:00 (Middle East & Africa) +971
42463266 Sun-Thu 9·00 – 17:30
(UAE) +971 8000320817 Sun-Thu 9:00 – 17:30
(KSA) +966 8008500030 Sun-Thu 8:00 – 16:30
(Kuwait) +965 22069086 Sun-Thu 8:00 – 16:30
(Egypt) +20 8000000826 Sun-Thu 7:00 – 15:30
(AU) +61 3 8331 4800 Mon-Fri 8 30 – 17:00 (AEST)
(TR) +90 0850 460 14 14 Mon-Fri 9:00 – 18:00
(RU) +8 (800) 511-86-23 Mon-Fri 9:00 – 18:00 (MSK)
For FAQs and more information, please visit:
anker.com/support
@anker _official
@AnkerDeutschland
@AnkerOfficial
@anker_Jp
@AnkerJapan
@Anker_JP
@Anker
Product Number: A2148 51005003400 V01
51008000564 V1
ANKER 737 POWER BANK
(PowerCore 24K)
QUICK START GUIDE
Charging Your Devices
Recharging Your Power Bank
Trickle-Charging Mode
Charge your accessories in trickle-charging mode.
(1)
To activate trickle-charging mode.
(2)
(3)
To exit trickle-charging mode.
LCD Screen Guide
- Remaining Battery
- USB-C1 Input / Output
- USB-C2 Output
- USB-A Output
- Time to Recharge / Remaining Battery in Hours
Specifications
Cell Capacity
| 24000mAh
(4000mAh*6pcs)
---|---
USB-C1 Input
| 5V ⎓ 3A / 9V ⎓ 3A / 15V ⎓ 3A / 20V ⎓ 5A / 28V⎓ 5A (140W Max)
USB-C1 / USB-C2 Output
| 5V ⎓ 3A / 9V⎓3A / 15V ⎓ 3A / 20V⎓5A / 28V⎓ 5A (140W Max)
USB-A Output
| 5V ⎓ 3A / 9V ⎓ 2A / 12V ⎓ 1.5A(18W Max)
Total Output
| 140W Max
For FAQs and more information, please visit:
anker.com/support
@anker _official
@AnkerDeutschland
@AnkerOfficial
@anker_Jp
@AnkerJapan
@Anker_JP
@Anker
Product Number: A1289 51005003422 V01
LCD Screen Information
Temperature| Battery temperature
Battery Health| Battery health
Total Input| Total recharging input
Battery Cycle| Number of battery charging/recharging cycles
Total Output| Total charging output
Screen Uses| Number of times the screen has lit up
- The Power Bank will automatically turn off if the screen is on standby for 30 minutes.
Important Safety Instructions
When using this product, basic precautions should always be followed,
including the following:
1). Store this product in a cool and dry place.
2). Do not store this product in a hot or humid environment.
3). Use of a power supply or charger not recommended or sold by the product
manufacturer may result in a risk of fire or personal injury.
4).Operating temperature should be between 0°C to 35°C / 32°F to 95°F.
5). Do not disassemble this product. Take it to a qualified service person
when service or repair is required. Incorrect reassembly may result in a risk
of fire or personal injury
6). If this product is not used for long periods of time, you should charge
and discharge it once every three months.
7). When charging a device, this product may feel warm. This is a normal
operating condition and should not be a cause for concern.
8). In normal conditions, the battery performance will decline over several
years.
9). Do not dispose of this product in heat or fire.
10). Do not clean this product with harmful chemicals or detergents.
11). Misuse, dropping, or excessive force may cause product damage.
12). When disposing of secondary cells or batteries, keep cells or batteries
of different electrochemical systems separate from each other.
13). Be aware that a discharged battery may cause fire or smoke. Tape the
terminals to insulate them.
14). CAUTION: Risk of explosion if the battery is replaced by an incorrect
type.
15). WARNING: The batteries (battery pack or installed batteries) shall not be
exposed to excessive heat such as from sunshine or fire.
16). A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
SAVE THESE INSTRUCTIONS
Note: Only connect your Power Bank to a 2021 Apple MacBook Pro (16″) using a USB-C to MagSafe 3 cable to achieve max power output (28V ⎓ SA) via a single port (USB-C1 / USB-C2).
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Directives 2014/35/EU, 2014/30/EU & 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address:
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
The following importers are the responsible parties (contract for EU and UK matters):
Anker Technology (UK) ltd
GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD171HP, United Kingdom
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications’. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
1). Reorient or relocate the receiving antenna.
2). Increase the separation between the equipment and receiver.
3). Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4).Consult the dealer or an experienced radio/ TV technician for help.
The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: + 1-800-988-7973
IC Statement
This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This digital apparatus complies with CAN ICES-003(B)/NMB-003(B).
Customer Service
24-month limited warranty* Lifetime technical support
support@anker.com
support.mea@anker.com (For Middle East and Africa
Only)
(US) +1 (800)988 7973 Mon-Fri 6:15AM- 5:00PM(PT)
(UK) +44 (0) 1604 936200 Mon-Sat 6:00- 19:00; Sun 6:00 -14:00
(DE) +49(0)69 9579 7960 Mon-Fri 8:00 – 16:00
(Middle East & Africa) +971 42428633 Mon-Thu 9:00 – 17:30; Fri 8:00 -12:00
(UAE) +971 8000320817 Mon-Thu 9:00-17:30; Fri 8:00-12:00
(KSA)+966 8008500030 Mon-Thu 8:00 – 16:30; Fri 7:00 – 11 :00
(Kuwait) +965 22069086 Mon-Thu 8:00- 16:30; Fri 7:00 – 11 :00
(Egypt) +20 8000000826 Mon-Thu 7:00-15:30; Fri 6:00-10:00
(AU) +61 3 8331 4800 Mon-Fri 8:30 – 17:00 (AEST)
(TR) +90 (850) 460 14 14 Mon-Fri 9:00 -18:00
(RU) +8 (800) 511–86-23 Mon-Fri 9:00 -18:00 (MSK)
*Please note that your rights under applicable law governing the sale of consumer goods remain unaffected by the warranties given in this Limited Warranty.
For FAQs and more information, please visit:
anker.com/support
@anker _official
@AnkerDeutschland
@AnkerOfficial
@anker_Jp
@AnkerJapan
@Anker_JP
@Anker
Product Number: A1289 51005003435 V01