Whirlpool WDF332PAMW Built In Full Console Dishwasher User Manual

Whirlpool WDF332PAMW Built In Full Console Dishwasher

Product Information

The Undercounter Dishwasher is available in the following model numbers:

• WDF110PAB
• WDF111PAB
• WDF120PAF
• WDF121PAF
• WDF130PAH
• WDF131PAH
• WDF320PAD
• WDF330PAH
• WDF331PAH
• WDF331PAM
• WDF340PAM
• WDF520PAD
• WDF540PAD
• WDF545PAF
• WDT530HAM
• WDT540HAM
• WDT710PAH
• WDT720PAD
• WDT730HAM
• WDT730PAH
• WDT735PAG
• WDT735PAH
• WDP540HAM
• WDP560HAM
• WDP730HAM
• WDF332PAM**
• WDF341PAP**
• WDT531HAP**

Drain Requirements

• A new drain hose is supplied with your dishwasher. If the drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/IAPMO test standards. The drain hose should be resistant to heat and detergent and should fit the 1″ (25 mm) drain connector of the dishwasher. Refer to the Tools and Parts section for part details and orders.
• Ensure that the drain hose is connected to the waste tee or disposer inlet above the drain trap in the house plumbing and at least 20″ (508 mm) above the floor. It is recommended to either loop up and securely fasten the drain hose to the underside of the counter or connect it to an air gap.
• If the drain hose is connected to house plumbing lower than 20″ (508 mm) above the subfloor or floor, an air gap must be used. Follow the air gap installation instructions and use a rubber hose (not provided) to connect to the waste tee or disposer inlet. Use 1/2″ (13 mm) minimum I.D. drain line fittings.

Water Supply Requirements

• This dishwasher requires a connection to a hot water supply line and has a water heating feature.
• Verify that you have a hot water line with water pressure ranging from 20 psi to 120 psi (138 kPa to 862 kPa). This can be confirmed by a licensed plumber.
• For the water supply line, use either 3/8″ (95 mm) O.D. copper tubing with a compression fitting or a flexible braided water supply line. Refer to the Tools and Parts section for part details and orders.
• Note: Do not use 1/2″ (13 mm) minimum plastic tubing.
• Do not solder within 6″ (152 mm) of the water inlet valve. If the dishwasher is being installed in new construction, ensure that the house water supply lines have been flushed prior to connecting the dishwasher to remove any debris that may exist in the supply line.
• If you are replacing an existing dishwasher, it is recommended to install a new water line and drain hose (supplied) with the new dishwasher. Refer to the Tools and Parts section for part details.

Electrical Requirements

WARNING: Plug the dishwasher into a grounded 3-prong outlet. Do not remove the ground prong, use an adapter, or use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock.

You must have:

• 120V, 60Hz, AC only
• 15A or 20A fused electrical supply
• Copper wire only
• A maximum of 2 field wiring supply conductors (12 AWG largest size) plus 1 grounding conductor are permitted in the terminal box
  We recommend using a time-delay fuse or circuit breaker and a separate circuit. If you are connecting the dishwasher with a power cord, use a UL Listed power cord kit marked for use with dishwashers. Refer to the Tools and Parts section for part details and orders. Plug into a grounded 3-prong outlet that meets all local codes and ordinances.

PRODUCT MODEL NUMBERS

• WDF110PAB
• WDF111PAB
• WDF120PAF
• WDF121PAF
• WDF130PAH
• WDF131PAH
• WDF320PAD
• WDF330PAH
• WDF331PAH
• WDF331PAM
• WDF340PAM
• WDF520PAD
• WDF540PAD
• WDF545PAF
• WDT530HAM
• WDT540HAM
• WDT710PAH
• WDT720PAD
• WDT730HAM
• WDT730PAH
• WDT735PAG
• WDT735PAH
• WDP540HAM
• WDP560HAM
• WDP730HAM
• WDF332PAM**
• WDF341PAP**
• WDT531HAP**

DRAIN REQUIREMENTS

•  A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and fits the 1″ (25 mm) drain connector of the dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.
•  Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20″ (508 mm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap.
• Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20″ (508 mm) above subfloor or
  floor.

Use of air gap

• If required, the air gap should be installed in accordance with the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.
• Use 1/2″ (13 mm) minimum I.D. drain line fittings.

WATER SUPPLY REQUIREMENTS

• This dishwasher has a water heating feature and also requires a connection to a hot water supply line.
• A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa) water pressure can be verified by a licensed plumber.
• 120°F (49°C) water at dishwasher.

Undercounter Dishwasher

• 3/8″ (95 mm) O.D. copper tubing with compression fitting or flexible braided water supply line. See the “Tools and Parts” section at the front of the guide for part details and orders.
  NOTE: 1/2″ (13 mm) minimum plastic tubing is not recommended.

• A 90° elbow with 3/4″ (95 mm) hose connection with rubber washer. See the “Tools and Parts” section at the front of the guide for part details and orders.

• Do not solder within 6″ (152 mm) of the water inlet valve.

• If installed in new construction, make sure the house water supply lines have been flushed prior to connecting the dishwasher to remove any debris that may exist in the supply line.
  NOTE: If replacing an existing dishwasher, it is recommended to install a new water line (see the “Tools and Parts” section at the front of the guide for part details) and drain hose (supplied) with the new dishwasher.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

You Must Have:

• 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply.
• Copper wire only.
• A maximum of 2 field wiring supply conductors (12 AWG largest size) plus 1 grounding conductor are permitted in the terminal box.

We Recommend:

• A time-delay fuse or circuit breaker.
• A separate circuit.

If Connecting Dishwasher with a Power Cord:

• Use UL Listed power cord kit marked for use with dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.
• Plug into a grounded 3 prong outlet. Outlet must meet all local codes and ordinances.

If Connecting Dishwasher with Direct Wiring:

• Use flexible, armored, or nonmetallic sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.
• Use a UL Listed/CSA Approved metallic strain relief.

DIMENSION

PRODUCT DIMENSIONS (FOR 331 AND 340 MODELS)

PRODUCT DIMENSIONS (FOR 500 AND 700 MODELS)

CABINET OPENING DIMENSIONS

• A. Measured from the lowest point on the underside of the countertop. May be reduced to 331 /2″ (851 mm) by removing the wheels and perforated area of insulation (blanket) on dishwasher.
• B. Minimum, measured from narrowest point of opening.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>