SZDOIT TS100 Chain Vehicle Metal Tank Chassis Robot Intelligent Car User Manual

User Manual for TS100 of
Shock Tank Chassis from SZDOIT

Part of the installation:

wheel： metal bearing wheel:https://gitnova.com/#/Robot/FrameChassis/Wheel/MetalBearingWheel/MetalBearingWheel
track: https://gitnova.com/#/Robot/FrameChassis/track/track
metal driving wheel: https://gitnova.com/#/Robot/FrameChassis/Wheel/MetaDrivingWheel/metaldrivingwheel
DC motor: https://gitnova.com/#/Robot/Engine/9vMotor/9vmotor
Controller：
Arduino UNO:https://gitnova.com/#/Robot/Controller/ps2/4motor16servo
ESPDuino:https://gitnova.com/#/Robot/Controller/controller/espduinoController
App : https://gitnova.com/#/Robot/Controller/app/AppforSmartCar

Introduction

This user manual is used for the installation of TS100, together with the motor connection with the development board. Specially, the installation is very similar to the other T series tank chassis, excluding the shock suspension. Therefore, the installation is very convenient. Here, we just take TS100 as an example to show the installation of TS series tank chassis.

Some useful links:
metal bearing wheel: https://gitnova.com/metal-wheel-for-tank-chassis/
track: https://gitnova.com/plastic-track/
metal driving wheel: https://gitnova.com/metal-driving-wheel/
DC motor: https://gitnova.com/9v-dc-motor/

Install the shock suspension (the total is 8pcs, including left and

right 4pcs)

2.1 Materials when install a shock suspension:

• installed bearing wheel: 1pcs
• shock suspension bracket: 1pcs
• cup bearing: 1pcs
• M4*8 screw: 2pcs
• M4 screw nut: 1pcs
• spring: 1pcs

2.2 Put the cup bearing into the centre hole of the shock suspension bracket. Importantly, the hook must on the top surface.

2.3 Use M4*8 screw to connect the bearing wheel and the shock suspension bracket

2.4 Use M4*8 screw and nut to fix on the side plate, shown in the following picture

Importantly, you must the direction of the bearing wheels are the same, shown in the following pictures.

Installation a bearing wheel to the side plate (left and right)

The wheel can adjust the length of track.
3.1 Material when install a bearing wheel

• bearing wheel: 1pcs
• 16mm gasket: 2pcs
• M4 screw: 1pcs

3.2 leave enough space to adjust the track when install this bearing wheel to the side plate

Install the driving wheel

4.1 materails

• metal panel: 1pcs
• left and right installed side plate with bearing wheel
• installed driving wheel: 2pcs
• motor: 2pcs
• track: 2pcs
• M3*12 screw: 8pcs
• M3 nut: 8pcs
• M3*10 screw: 4pcs

*4.2 Install the motor with m36 screw**

4.3 Install the driving wheel and connect the motor

4.4 Install the metal panel

4.5 Install the track to the wheel. *Note, the length can be changed randomly.

Some Warm Tips

• Align the location hole when install the wheels;
• Track can be changed randomly;
• Note the screw models when install the car;
• M2 screw don’t fix to tight when install the bearing wheel;
• By adjusting the location of the end of bearing wheel, can adjust the track;
• The same direction is necessary when install the shock suspension;

Contact Us

E-mails: yichone@doit.am , yichoneyi@163.com
Skype: yichone
WhatsApp:+86-18676662425
Wechat: 18676662425

Documents / Resources

| SZDOIT TS100 Chain Vehicle Metal Tank Chassis Robot Intelligent Car [pdf] User Manual
ts100-all, SZDoit, SZDoit, SZDoit, Smart, Shock, Absorption, Robot, Tank, Car, Chassis, Kit, with, Suspension, System, for, Arduino, Raspberry, Pi, DIY, STEAM, Education, Platform, Tracked, Vehicle, Black, Frame, Silver, Wheel, B097K346JF, B097JX7296, B096DHBTX3, B089475848, TS100, TS100 Chain Vehicle Metal Tank Chassis Robot Intelligent Car, Chain Vehicle Metal Tank Chassis Robot Intelligent Car, Metal Tank Chassis Robot Intelligent Car, Tank Chassis Robot Intelligent Car, Chassis Robot Intelligent Car, Robot Intelligent Car, Intelligent Car, Car
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>