opentrons GEN2 Thermocycler Module User Guide

June 13, 2024
opentrons

opentrons logo Thermocycler Module GEN2
Quickstart Guide

opentrons GEN2 Thermocycler Module Opentrons Labworks Inc.
Edition
GEN2, December 2022

Product Elements

opentrons GEN2 Thermocycler Module - Product Elements

Setup Instructions

VENTILATION REQUIREMENTS
To allow for sufficient fan output from the Thermocyler, at least 20 cm / 8 inches of empty space is required between the unit and a wall.

opentrons GEN2 Thermocycler Module - wall

Also for ventilation, and to provide enough space for the power and USB cables to connect to the module, Opentrons advises using the OT-2 side and rear panels shown below:

opentrons GEN2 Thermocycler Module - rear panels

Note: These panels are included with newer models of the OT-2. They only need to be replaced on older models of the OT-2.

DECK PLACEMENT AND CONNECTION

  1. Carefully place the Opentrons Thermocycler in deck slots 7, 8, 10, and 11. Lift the module care- fully, using two hands (the module weighs 8.4 kg, which is quite heavy for its size).
    opentrons GEN2 Thermocycler Module - Thermocycler

  2. Connect the Thermocycler to the OT-2 and power supply by plugging in the USB cable and screwing the power cable into the unit as shown. Be sure to route the cables through the opening in the polycarbonate side panel.
    opentrons GEN2 Thermocycler Module - side panel| Connect the USB cable to the module and an open USB port at the back of the robot
    ---|---
    | Connect the power supply connector to the Thermocycler and then screw it on for safety
    | Connect the power cable to the back of the power supply and the wall outlet

opentrons GEN2 Thermocycler Module - front

  1. Once everything is connected, power on the OT-2 and the Thermocycler power supply. If you see a white light on the Thermocycler, it is powered on.
    You can open and close the lid of the Thermocycler by pressing the round button on the front.
    RUBBER AUTOMATION SEALS
    Your Opentrons Thermocycler comes with 5 rubber automation seals to help reduce evaporation. Each seal must be sterilized before use and can be used for several runs. You should check the state of the seal after each run and replace it if needed. Worn or  damaged seals may result in increased evaporation of samples.

  2. Apply a seal to the lid of the module, not directly to the plate, to enable pipetting access.
    opentrons GEN2 Thermocycler Module - plate

  3. After applying the seal, wipe it with a 1:10 dilution of bleach and let it dry. Wipe it down with molecular biology grade water and let it dry again.

Note: Seals must be sterilized before your first Thermocycler run. Thermocycler seals cannot be autoclaved.

Resources

MAINTENANCE
Users should not attempt to service or repair the Thermocycler Module themselves. If you have concerns about your module’s performance or require maintenance, please contact Opentrons Support.

SUPPORT
Opentrons Help Center
Answers to many common questions are available on the Opentrons Help Center at https://opentrons.com/support.

Contact Opentrons
If you have any other questions, contact support@opentrons.com. Please have the serial numbers of your module and robot available when contacting Opentrons Support.

Warranty
All hardware purchased from Opentrons is covered under a 1-year standard warranty. Opentrons warrants to the end-user of the products that they will be free of manufacturing defects due to part quality issues or poor workmanship and also warrants that the  products will materially conform to Opentrons’ published specifications.

APP DOWNLOAD
Control your liquid handling robot and module using the Opentrons App. Download the app for Windows, macOS, or Ubuntu at https://opentrons.com/ot- app/.

Product and Manufacturer Description

PRODUCT DESCRIPTION
The Opentrons Thermocycler Module GEN2 provides ondeck, fully automated thermocycling. The module enables automation of upstream and downstream workflow steps.
Completed Certifications
IEC/UL/CSA, EN/BSI, FCC, IC
Recommended Operating Conditions
Environmental temperature: 20–25 °C
Environmental humidity: 30–80%, non-condensing
MANUFACTURER DESCRIPTION
Opentrons Labworks Inc
45-18 Ct Square W
Long Island City, NY 11101

For a PDF of the complete Opentrons Thermocycler Module GEN2 Instruction Manual, scan this QR code:

opentrons GEN2 Thermocycler Module - qr codehttps://insights.opentrons.com/hubfs/Products/Modules/Thermocycler%20GEN2%20Manual.pdf

opentrons logo Post-sales service & contacting Opentrons
If you have any questions about the use of the module
or your Opentrons platform, please contact:
support@opentrons.com. Also visit www.opentrons.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals