Billi B-3000 Sparkling Tap User Guide
- June 13, 2024
- Billi
Table of Contents
User guide
Billi B-3000 Sparkling
(913100)
Version 11/2021
Warnings & Important information
-
For continued safety of this appliance it must be installed, operated and maintained in accordance with the manufacturer’s instructions .
-
Your appliance should be installed by a suitably qualified tradesperson .
-
For correct operation of this appliance it is essential to observe the instructions as outlined in this booklet .
-
Do not use this appliance with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system . Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts .
-
Filter replacement must be performed at intervals of not more than 12 months .
-
Use this appliance only as directed in these instructions and only for its designed purpose .
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety .
-
Children should be supervised to ensure that they do not play with the appliance .
-
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid creation of a hazard .
-
New hose sets supplied with the appliance are to be used . Old hose sets should not be re-used .
-
The appliance is intended to be used in household and similar applications such as:
• Staff kitchen areas in shops, offices and other working environments
• Farm houses and by clients in hotels, motels and other residential type environments
• Bed and breakfast type environments
• Catering and similar non-retail applications -
WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
-
WARNING: Do not locate multiple portable socket – outlets or portable power supplies at the rear of the appliance.
-
WARNING: Avoid spillage on the connector.
-
WARNING: Potential injury from misuse.
Please note maximum water inlet pressure is 0.6MPa
**General Maintenance
**
Your Billi B-3000 has been designed to require minimal maintenance other than
replacement of filter cartridges . During each filter change, check all water
connection fittings for signs of leakage . Check all tubing for any signs of
damage . Check the cupboard area around the base of unit for any signs of
moisture .
Cleaning the dispenser
Your B-3000 Dispenser is fabricated from robust metal with a tough protect
chrome plating . Care of dispenser is as with any chrome plated tapware .
Avoid using abrasive cleaners . Wipe clean using a damp cloth . Use of a non-
solvent, non-smearing cleaner
such as Windex is recommended . Do not pour water over dispenser .
Cupboard ventilation requirements
Your B-3000 Sparkling underteach module requires cupboard ventilation, refer
to install guide for details . Care should be taken when using the cupboard
space, to avoid stretching or damaging plastic pipe work . Check fittings and
tubing at each filter change for signs of damage or leakage . Always ensure
access to power switch and water supply tap is not restricted .
Features and Modes
Slimline Dispenser
To dispense filtered water, the dispenser tap lever will need to be rotated .
The lever will automatically return to the off position . The spout can be
swiveled to suit your installation .
Adjustable chilled water temperature
The chilled water delivery temperature can be adjusted to suit your preference
. The blue control knob, located on the front of the Chiller Module, can be
adjusted if a cooler or warmer temperature is required .
Filter Cartridges Service Interval
Periodic replacement of your Billi B-3000 filter cartridge is necessary to
maintain the sparkling freshness of your drinking water .
Your Billi Representative will advise you of an appropriate service interval .
As a guide, the filters should be serviced twice yearly . In areas where water
supply has a high level of sediment, more frequent replacement of filter
cartridges may be necessary . This will become evident when a significant drop
in delivery flow rate occurs.
Filter Cartridge Replacement
When you receive your replacement cartridges, follow the procedure as outlined
below:
- Turn off blue tap under bench.
- Operate dispenser lever to release pressure.
- Hold filter and swing towards you slowly. The top of the filter is in a hinged cradle assembly . It should stop after approximately 30 degrees of travel .
- The filter can now be released from the holding cradle by pulling down on the filter.
- Take care not to spill water in the base of the tray . If so wipe gently with absorbent paper.
- Install new filter into the same location by pushing all the way up into the cradle.
- Push filter back into the unit until it locks into place .
- Turn on blue tap under bench and check for water leaks .
- Operate dispenser lever and run water for 3 minutes to flush and condition the new filter.
Removing the CO2 cylinder
-
Turn off the CO2 regulator by turning the black knob anti-clockwise . Refer diagram A.
-
Drain any remaining pressure by activating the sparkling water on the dispenser installed.
-
Turn off the power. This will prevent the internal pump from pressurizing the system. Ensure the pressure gauge shows near to zero pressure.
– If the pressure is less than one bar, and the dial is fully anti-clockwise, then the cylinder can be removed with only a small amount of CO2 escaping. -
Hold the regulator and rotate the cylinder clockwise to remove. If the bottle is not empty, CO2 may escape while you are turning the bottle. The bottle will self-seal prior to the thread being free from the regulator. Refer diagram B.
– Avoid breathing air containing CO2 or contact with the cold escaping gas as per the Safety Data Sheet.
Installing the CO2 cylinder
-
Ensure all connections between the regulator and unit are secure . Position the regulator on top of the CO2 cylinder .
-
Tighten the bottle by rotating anti-clockwise.
– CO2 will escape while you are turning the bottle . Continue to turn the bottle to form a seal with the regulator . Refer diagram A. -
Open the pressure regulator by turning the black knob clockwise . Refer diagram B.
– Set the initial pressure to around 4 Bar . Refer diagram C.
– Turn on the unit power and wait for the unit to come back to temperature. -
Check bottle and connections for leaks using soapy water to test for bubbles.
NOTE: the ¼” tube and push fit fittings may settle when the pressure is turned on. -
Increase the pressure to set your level of carbonation. Initial set point may vary once the unit is running, you may need to reset the pressure once the system has stabilised.
WARNING: Do not set the pressure above 5 bar.
|
---|---
Thank you for choosing to install a Billi B-3000 Sparkling Drinking Water
Appliance . Your B-3000 Sparkling is manufactured to exacting standards using
high quality materials and with proper maintenance and care, should function
for many years .
For information on our filtration and service contract please contact Billi
Head Office on 1800 812 321 or email us at
service@billi.com.au.
For technical support please call 1800 812 321 and speak to one of Billi’s
experienced technician’s .
To book a service call out request a filter change or please contact the Billi
Service Centre on 1800 812 321 or book online at
www.billi.com.au
Filter cartridges are also available for purchase online at
www.billi.com.au
Billi Australia Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone 1800 812 321
www.billi.com.au
Designed and manufactured in Australia .
As Billi Australia Pty Ltd has a policy of
continual improvement, all details are
subject to change without notice . All
goods are sold subject to our published
terms and conditions . Billi is a
registered trademark . 1220
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>