Pyle PDIC106 Ceiling Wall Mount Speakers Installation Manual
- June 13, 2024
- Pyle
Table of Contents
Pyle PDIC106 Ceiling Wall Mount Speakers
TECHNICAL PARAMETERS
| PD IC56 | PD IC66 |
|---|---|
| 5.25″ 2- W ay Ceiling SpeakerSystem | 6.5″ 2- W ay Ceiling SpeakerSystem |
| *Black PP Cone W ith RubberEdge | *Black PP Cone W ith RubberEdge |
| *1/2″ Titanium D om e TweeterIn Sw ivelM ount | *1/2″ Titanium D om e Tw eeterIn Sw ivelM ount |
| *Pow er:150 W atts Rated Peak | *Pow er:200 W atts Rated Peak |
| *Frequency Response:80H Z- 20KH Z | *Frequency Response:60H Z- 20KH Z |
| *Im pedance:8 O hm s | *Im pedance:8 O hm s |
| *Sensitivity:88 dB | *Sensitivity:89 dB |
| *w ith Electronic CrossoverN etw ork | *w ith Electronic CrossoverN etw ork |
| *Supplied W ith Round G rilles And Square G rilles | *Supplied W ith Round G rilles And Square G rilles |
| Size:Round / Square G rilles:8 3/”10 /83/10”83/10” | Size:Round / Square G rilles:9 1/”2 /91/2”91/2” |
| *CutoutSize:64/5” | *CutoutSize:8” |
| *M ounting D epth:3” | *M ounting D epth:3” |
| PD IC86 | PD IC106 |
|---|---|
| 8″ 2- Way Ceiling SpeakerSystem | 10″ 2- Way Ceiling SpeakerSystem |
| *Black PP Cone W ith RubberEdge | *Black PP Cone W ith RubberEdge |
| *1/2″ Titanium D om e TweeterIn Swivel Mount | *1/2″ Titanium D om e TweeterIn Swivel Mount |
| *Pow er:250 Watts Rated Peak | *Pow er:300 Watts Rated Peak |
| *Frequency Response:40H Z- 20KH Z | *Frequency Response:35H Z- 20KH Z |
| *Im pedance:8 O hm s | *Im pedance:8 O hm s |
| *Sensitivity:89 dB | *Sensitivity:89 dB |
| *with Electronic CrossoverNetw ork | *with Electronic CrossoverNetw ork |
| *Supplied With Round G rilles And Square G rilles | *Supplied With Round G rilles And Square G rilles |
| Size:Round / Square G rilles:111/”5 /111/5”111/5” | Size:Round / Square G rilles:124/”5 /12 4/”5 12 4/”5 |
| *CutoutSize:92/5” | *CutoutSize:101/2” |
| *Mounting D epth:31/2” | *Mounting D epth:3 4/5” |
INSTALLATION
The in-wall/in-ceiling speakers were designed to be easily installed.However,if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer.
TOOLS NEEDED
TROUBLESHOOTING
- IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
- Check that the receiver/amplifier is on and a source is playing.
- Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or touching each other.
- Review the proper operation of your receiver/amplifier.
- IF THERE IS NO SOUND COMING FROM ONE SPEAKER:
- Check the“Balance” control on your receiver/amplifier.
- Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or punching each other.
- IF THERE IS LOW(OR NO)BASS OUTPUT:
- Make sure the connections to the left and right“speaker Inputs” have the correct polarity(+ and -).
- Consider adding a powered subwoofer to your system.
- In Dolby Digital or DTS modes, make sure your receiver/processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as“LARGE” See your receiver/processor’s owner’s manual for further information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.
- IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:
- Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured, or touching each other.
- If more than one pair of main speakers is being used, check the minimum impedance requirements of your
receiver/amplifier.
Thank you for purchasing this PYLE in-wall/in-ceiling speaker system. It is a state-of-the-art product carefully designed and manufactured for your installation needs and has been thoroughly tested to ensure consistent and reliable performance.
If you have any questions about the installation or operation of your PYLE in- wall/in-ceiling speaker system which are not answered by this manual, contact your dealer immediately.
INCLUDED COMPONENTS
IN-CEILING SPEAKERS
One pair of speakers with grilles. One pc of speakers with grills for PDIC56/PDIC66/PDIC86/PDIC106
SPEAKER PLACEMENT
FRONT SPEAKERS
REAR SPEAKERS
IN-CEILING
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listener’s ears will be, with the tweeters aimed toward the listener at ear-level height. In a home theater configuration, the two surround, speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listener’s ears. If that is not possible, they may be placed in a wall(or in the ceiling)behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers. In Dolby*Digital and DTS systems, aim the tweeters toward the listening position at ear-level height.
SPEAKER CONNECTIONS
CONNECTION TIPS
- The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding(+) and(-)terminals.
- We use red to denote the(+)terminal and black for the(-)terminal.
- It is important to connect both speakers identically:(+)on the speaker to(+)on the amplifier and(-)on the speaker to(-) on the amplifier. Wireing“out of phase” results in thin sound, weak bass, and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambiance and directionality of the program material.
EXISTING CONSTRUCTION
IN-CEILING SPEAKERS
-
Cut the drywall.
Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place. -
Connect the speaker wires to the speaker
-
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall.
Put in the strips of adhesive to secure the grille.
-
Replace the metal grille.
-
Complete.
The manual includes information about PDICI06 PDC86 PDIC66 PDC56 model numbers.
- 1600-63rd Street Brooklyn, NY 11204 USA
- www.pyleaudio.com
FAQs
What brand manufactures the PDIC106 speakers?
The PDIC106 speakers are manufactured by Pyle.
How can the PDIC106 speakers be installed?
The PDIC106 speakers can be installed in two ways: in-wall or in-ceiling flush mount using the convenient spring-loaded clips.
What is the special feature of these speakers?
These are 2-way mount speakers with a flush mount design and built-in electronic crossover network.
What is the connectivity technology for these speakers?
The PDIC106 speakers are wired.
What's the frequency response of these speakers?
The speakers have a frequency response ranging from 35Hz to 20kHz.
What's the power handling capability of these speakers?
They have an impressive 250 watts peak power handling capability.
What are the dimensions and weight of the product?
The product dimensions are 13 x 13 x 10.8 inches, and the item weighs 12.13 pounds.
What is the construction material of the speaker grills?
The speaker grills are stain-resistant and are interchangeable between round and square designs.
Are there any templates provided for installation?
Yes, a cut-out template is provided for easy and quick installation.
Can these speakers be used in a professional setting?
Yes, they can be utilized in various settings, including homes, offices, conference rooms, assembly halls, and more.
How do the speakers reproduce sound?
The Pyle PDIC106 speakers are equipped with a high compliance polymer tweeter and a polypropylene cone with a rubber edge, ensuring clear and wide-ranged sound performance.
What's the impedance and sensitivity rating for these speakers?
The speakers have an 8 ohm impedance rating and an 89 dB sensitivity.
Download This PDF Link: Pyle PDIC106 Ceiling Wall Mount Speakers Installation Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>