LEEDARSON A19 Smart LED Light Bulb Instruction Manual

LEEDARSON A19 Smart LED Light Bulb

Product Information

Product Name: Smart A19 LED Light Bulb, Color Changing
Brand Name: LEEDARSO
Working Voltage: 120Vac

FCC Compliance Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

   • This device may not cause harmful interference.
   • This device must accept any interference received, including
     interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Warning Statement

The device has been evaluated to meet general RF exposure.

FCC Compliance Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   • this device may not cause harmful interference, and
   • this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver.
• connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Warning Statement: The device has been evaluated to meet general RF exposure requirements. This device should be installed and operated with minimum distance of 8” (20 cm) between the radiator and your body.
Canada IC Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Blub Stats Guide

connected
Flashes five times quickly, then flashes twice softly in soft white.| Factory reset is complete. Bulb is ready for setup again.

Set Up your Smart LED Light Bulb with Alexa

A DANGER Risk of fire, electric shock, or death! Before replacing, make sure the light is powered off.

1. Download the latest version of the Alexa app from the app store and log in.
2. Screw in the smart LED light bulb and turn on the light. It will flash twice softly, indicating the bulb is ready for setup.
3. Open the Alexa app and tap the More icon on the bottom-right of the screen. Tap Add a Device, select Light, Amazon Basics, then select your corresponding device. Follow the on-screen instructions. If prompted by the app, scan the barcode on the back page of the quick start guide.
   (DON’T scan the barcode on the packaging)

Alternative setup methods

Option 1
To add the device with the barcode on the light bulb, follow these steps:

1. Keep the light bulb switched off and unscrew it from socket
2. Open the Alexa app and tap the More icon to add a device. Scan the barcode on the light bulb when prompted by app.
3. Screw the bulb back into the socket and switch on the light again.
4. Follow the on-screen instructions in the Alexa app to complete the setup.

Option 2
If the barcode scan setup fails, select DON’T HAVE A BARCODE?, then follow the on-screen instructions to complete setup:

1. Make sure your device is powered on for at least five seconds, then switch it off.
2. Use a light switch to quickly turn on and off the light five times. At the sixth turn on, it flashes five times quickly, then flashes twice softly.
3. Press NEXT on the screen then follow the on- screen instructions to complete setup.

Use with Alexa Voice Commands

To use your bulb with Alexa, just say,
“Alexa, turn off first light.”

Frequently Asked Questions

NOTICE
For more FAQ and more information, go to the product detail page.

1. Problem 1
   How do I reset the light bulb?
   Solution 1
   You can do a factory reset by deleting your device from the app. If you are not able to delete your device from the
   Alexa app: use a light switch to quickly turn on and off the light five times. At the sixth turn on, it flashes five times quickly, then flashes twice softly, indicating you have successfully factory-reset your light bulb, and it is ready for setup again.

2. Problem 2
   Amazon Alexa app cannot find or connect to the smart LED light bulb.
   Solution 2

   • Check that your phone/tablet and the Alexa app have the latest software version.
   • Make sure that your phone/tablet and your smart LED light bulb are connected to the same 2.4 GHz Wi-Fi network. The bulb is not compatible with a 5 GHz Wi-Fi network.
   • Check that your phone/tablet is within 30′ (10 m) of your smart LED light bulb.
   • Restart your smart LED light bulb. To restart, power off the smart LED light bulb and power it back on.
   • If you have restarted your smart LED light bulb and it is still not working, reset your light bulb following the steps in Solution 1.

3. Problem 3
   What if I lose the Quick Start Guide, how can I set up my smart light bulb?
   Solution 3
   You can set up your device via two alternative setup methods. The instructions can be found in Section 2.1 Alternate setup methods.

4. Problem 4
   Error code (-1:-1:-1:-1) displays on the screen.
   Solution 4
   Make sure your phone has Bluetooth turned on throughout the entire setup process and the device you are trying to setup is in pairing mode. Restart your device by powering it off and on, and then set up again.

Important Safeguards

Read these instructions carefully and retain them for future use. If this bulb is passed to a third party, then these instructions must be included.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>