Types S Auto LM57848 LED 9004 FOG LIGHT Kits for car Instruction Manual

: June 5, 2024
: Types S Auto

Table of Contents

Package Includes
Specifications
Product Overview
Installation
Installation Steps by Fog Light Type
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Auto LM57848 LED 9004 FOG LIGHT Kits for the car
Instruction Manual

LED FOG LIGHT
WP ITM. LM57848, LM57849, LM57850, LM57851, LM57852, LM57853, LM58162, LM58163 Care & Use Instructions
High-Performance Electric Cooling Fans Important, retain for future reference: Read carefully

Package Includes

2 x Ultra Bright Fog Light LEDs
4 x Cable Ties
1 x Installation Guide
For LM57850 only:
2 x 9006 Mounting Rings
2 x 9005 Mounting Rings (Pre-installed)

Specifications

Operation voltage: 12V/ 24V
Operation temperature: -40°F to 194°F (-40 °C to 90 °C)
Current: 2A@12V / 1A@24V +/- 10%
Color temperature: 6,500 K ± 510 K
Lumen (Maximum):
Dual Beam: High – 1,200 LM ± 15%
Low – 1,200 LM ± 15%
Single Beam: 1,800 LM ± 15%
Cable length with plug: 3.9 inch (10cm)

Product Overview

Installation

Remove the mounting ring from the Fog Light.| Insert the mounting ring into the socket and affix with metal spring.
Insert the Fog Light body.| Rotate clockwise to secure.
Connect the plug to the Fog Light connector.| Turn on the Fog Light, and make sure it is lighted up correctly.

NOTE: Perform Steps 1 and 2 only on LM57848 (H4) and LM57852 (H7).

Installation Steps by Fog Light Type

Review the vehicle’s owner’s manual or service manual to reference how to access your light bulbs.
9005 / 9006
The interchange of the 9005 / 9006 mounting ring needs to be done using a screwdriver:
i. Remove the 9005 blue rubber ring.
ii. Unscrew and pull out the 9005 mounting rings. has its label on the back)
iii. Insert the 9006 mounting rings and tighten the screw.
iv. Insert the 9006 blue rubber ring.
9004/9005/9006/9007/9012/H8/H9/H11/H13/H16JP

Remove the headlight dust cover.
Insert the Fog Light body.
Rotate clockwise to secure.
Connect the plug to the Fog Light connector
Put the dust cover back.
Turn on the Fog Light, and make sure it is lighted and the direction of the beam is correct.

H4/H7

Remove the headlight dust cover.
Pull out the mounting ring from the Fog Light.
Insert the mounting ring into the socket and fix it with the metal spring.
Insert the Fog Light body into the socket.
Rotate clockwise to secure.
Connect the plug to the Fog Light connector.
Put the dust cover back.
Turn on the Fog Light, and make sure it is lighted and the direction of the beam is correct.

NOTE: There are some cases when the LM57849 (H8/H9/H11/H16JP), LM57850 (9005/9006), LM57852 (H7), and LM58163 (9012/HIR2) Fog Lights will not turn on after plugging in. It is because they may not be universal for every make/model of vehicle. Often times the positive and negative terminals are on the opposite side. When you come across this situation, please follow these steps:

Flip the plug halfway around and plug it into the Fog Light connector. Turn on the headlights and check if the light is on.
Put a cable tie, or a piece of electrical tape to hold the connector securely, since the notch is no longer locked onto the clips.

Notes:

Some vehicles require the engine to be started for the operation of all beams. If the LED light does not turn on then rotate the plug and try again.
The headlight dust covers of some vehicles may not be put back successfully after the Fog Lights are installed. Look for the correct third-party dust covers as a replacement.
This Fog Light fits exclusively to 12V-24V vehicle input.
When fetching and installing the Fog Lights, DO NOT touch the LED chips with your fingers to avoid injury.
Try to not block or obstruct the airflow of the cooling fan.
Before installing, please make sure the Fog Lights are free from damage, fracture, and no impurities on the LED chip.
For additional installation and product information, visit typesauto.com.

Warnings:

Caution! If you get an error code, or lights are flickering, use a decoder to complete the installation. The decoder is sold separately.
Considering the high intensity of light, DO NOT stare at the light when it is switched on.
The surface of the LED will reach a very high temperature when it is turned on. DO NOT touch the surface directly to avoid severe burns.
Before changing the original Fog Lights, make sure it is turned off and cooled.
Keep LED chips of the Fog Lights free of dust, and oil.
Do not install or use the product if it, in any way, impairs the safe operation of your vehicle.
Follow the manufacturer’s instructions to ensure the product is properly & safely installed.
Check your state or provincial laws before installing. The vehicle owner must comply with all applicable laws.
This product is intended solely for Off-road / Fog light purposes.
Manufacturer and Seller assume no liability for installation or use, which are solely the responsibility of the purchaser.
This product is not DOT approved and is designed and intended for Off-road/Fog light uses only.
Do not install or use the product if it, in any way, impairs the safe operation of your vehicle. Not for use in extreme temperatures.
The manufacturer and seller are not responsible or liable for consequential, incidental, or indirect damages, whether to person or property, resulting from the installation or improper use of this product.

Made in China

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format) >>

Download This Manual (PDF format)

Download this manual >>