SWARN JAL Aquasense Indicator with Dual Alarm Instruction Manual

SWARN JAL Aquasense Indicator with Dual Alarm

AQUASENSE:

This product provides a wired solution to user for alarming user before Overflow and Empty water tank with 4 Water Levels. If water tank is full, Device Alarms the user to switch off the Water Pump. Also, Device alarms the user if Water tanks reaches the Reserve water level so that User can use the remaining water Cautiously or Switch on t he pump to avoid Empty tank Situations.
Salient features of the Device are.

1. Overflow Alarm that shut offs Automatically after 4S Seconds.

2. Reserve water Alarm that Warns user for Low water level in the tank.

3. No need of CatS/6 Cable : Only single pair Cable required for Connecting Sensor hub and Main Device.

4. Shock Proof ; Device runs on 2 AA batteries that last over an year for a typical use.

5. TOUCH FOR LEVEL If user touches the button for short time, Instant water level Is displayed to the user for better Level indication.
   RED – Level 1 (RESERVE),
   BLUE-Level 3,
   YELLOW- Level 2,
   GREEN – Level 4 (FULL)

6.  Wire Breakage Indication : VIOLET LED will be shown that wire is broken so that proper action can be taken.

7.  Device Malfunction Warning Device will show WHITE Light If there is some issue in Device. Also, if wires are connected in wrong way then indicator will Continuously blink RED light at all levels.

8.  Low Battery Warning: Device gives short beeps at 2 Hours Interval when battery is about to drain.

9. Intelligent Operation makes device free from false alarms, it takes S Seconds of stabilization to Avoid false alarms.

How to Test the Device?

Open the Box and User will see 2 Units (Main Unlit and Sensor Hub) connected using a copper wire.
These 2 wires are joint together, You need to touch these wires as extension wire needs to be attached for Installation purpose but before installation we can check the working of device with following steps:
Short Touch means less than 2 seconds touch. Long Touch means 2 seconds touch or more.
INSERT BATTERIES : User needs to insert 2 AA batteries (Preferred Alkaline Batteries like Duracell, Energizer, GP Line etc.) in the back side of Main unit. This will start the unit with a Green, Red & Blue Blink in the Indicator.

Untangle All the sensors: Separate all the sensors from each other and take a plastic glass (not steel) of
water for testing.

DIP SENSORS in the Water: Dip the Red and Yellow sensor in the water and wait for 5 Seconds, this will
indicate Yellow color in the indicator,
Now dip the BLUE sensor with previous ones and wait for 5 Seconds, this will indicate Blue color in the indicator.
Now dip the GREEN sensor with previous ones and wait for 5 Seconds, this will indicate GREEN color in
the indicator and give a loud Alarm for 45 seconds. Short Touch the Round button just below the indicator and Alarm will go OFF. After 45 seconds alarm will go off automatically.
Now remove BLUE and GREEN wire and wait for 5 seconds until Yellow color is not shown in the indicator.
Remove the Yellow wire and wait for 5 Seconds. This will Give RED color and 20 Loud Beeps that indicates that water in the tank has reached Reserve Level. Short touch to shut off the beeps.

SHORT TOUCH: Current Level will be prompted to the user on short touching the Switch.

LONG TOUCH: Device will switch off and switch on if user long touches the switch. Device will give a short Beep Sound and Red light in indicator for Switch OFF and Short beep followed by Green, Red & Blue blink for Switch ON.

INSTALLATION GUIDE

Device has very simple procedure for installation. In the box you will find Main unit and a sensor hub. Sensor Hub/Transmitter has Four sensor wires:

1. RED Wire: This is common wire and goes to the base.
2. YELLOW Wire: This is reserve level Wire and should be just above Reserve water level in the tank (Approximate 30% of full Capaci ty).
3. BLUE Wire: This is Level 3 .. Wire and should be at Approximate 60% of full Capacity.
4. Green Wire: Full Water tank wire that should be just below the overflow pipe. Cut these wires as per the lengths mentioned above with respect to the tank and re-attach the Sensor Wires. Device won’t work properly if these copper wires are not attached properly.

Now Fix the sensor Hub on the inner roof of the tank with Double sided tape. This is Professional
double-sided tape and doesn’t loose wit ho time. Make Sure that Tank Roof is properly cleaned
Before Affixing the Hub.
Connect the transmission wires with the extension wire considering the polarity (The same colored wires should be attached with their same colored w ire to the main unit) If transmission wires are not **connected properly then device will only Red Colo, irrespective of the Level in Water Tank.

**

Now Attach the main unit to transmission wires, ,again taking care of the polarity (Not Connecting Wrong wire to each other) and insert the 2 AA batteries into the unit (Alkaline like Duracell, Energizer etc. Batteries Preferred). The device will start with a Green, Red & Blue Bl inking LED.
Indicator LED will take nearly s-10 seconds to Initiate the operation.
After that it will show respective COLOR (RED, YELLOW/AMBER, BLUE, GREEN).
Device has a touch button just below the indicator that has following Working:
Short Touch {less than 2 seconds) -Shut off the buzzer.
Long Touch (2 seconds) -ON/OFF the device.

Policy:

Safety Measures that you need to follow

Thank you for choosing our company’s electronic product. We are committed to providing high-quality products that meet stringent safety standards. However, it is essential to understand and follow safety precautions to minimize any potential risks, including the risk of electric shock. Please read and adhere to the following safety disclaimer:

1. Electrical Knowledge: Our electronic products are designed for use by individuals with basic electrical knowledge or under the supervision of a qualified professional. It is important to understand the basic principles of electricity, such as voltage, current, and grounding, before operating or attempting to repair the product.

2. Professional Installation: For electronic products, such as those requiring direct electrical connections or modifications to existing wiring, we strongly recommend hiring a licensed electrician or a trained professional for installation. Incorrect installation can lead to electric shock hazards.

3. Power Source: Ensure that the electronic product is connected to a power source that meets the specified requirements mentioned by the company. Unstable or improper power sources can increase the risk of electric shock. Avoid using extension cords or adapters that are damaged or not rated for the product’s power requirements.

4. Water and Moisture: Keep the electronic product away from water, liquids, and excessive moisture. Do not operate the product if it has been exposed to water or if there is any indication of water damage.
   Water and moisture can increase the risk of electric shock.

5. Physical Damage: Avoid subjecting the electronic product to excessive physical force, dropping it, or exposing it to impact. Physical damage can compromise the integrity of the product’s electrical components, potentially leading to electric shock hazards.

6. Repair and Maintenance: Only authorized technicians should perform repairs or maintenance on the electronic product. Opening the product or attempting repairs without proper knowledge and expertise can result in electric shock or other hazards. Contact our customer support for assistance or to locate an authorized service centre.

7. Unplug During Maintenance: Before performing any cleaning, maintenance, or repairs on the electronic product, disconnect it from the power source. Failure to do so can expose you to electric shock hazards.

8. Children and Pets: Keep electronic products out of the reach of children and pets, especially when connected to a power source. Do not allow them to handle or tamper with the product to prevent potential electric shock or other accidents.

9. Reporting Safety Concerns: If you encounter any unusual behavior, electrical issues, or suspect a potential safety hazard with the electronic product, immediately disconnect it from the power source and contact our customer support. Your feedback is invaluable in helping us address and resolve any safety concerns promptly.

Remember, while our company takes all necessary precautions to ensure product safety, the responsibility for safe usage ultimately lies with the customer. By acknowledging and adhering to these safety guidelines, you can help protect yourself and others from the risk of electric shock or other electrical hazards.
If you have any questions or require further clarification, please do not hesitate to contact our customer support team.

Contact Us

If you have any questions about these Terms and Conditions, You can contact us:

• By email : [email protected]
• By WhatsApp/Call: +91-9050526154

Return/Refund/Guarantee Policy

Thank you for shopping at Prick home Technologies Pvt. Ltd.

If, for any reason, you are not completely satisfied with a purchase We invite You to review our policy on Return/Refund/Guarantee Policy. This Return/Refund/Guarantee Policy has been created with the help of the Return/Refund/Guarantee Policy Generator.

The following terms are applicable for any products that You purchased with Us.

Interpretation and Definitions

Interpretation

The words of which the initial letter is capitalized have meanings defined under the following conditions. The following definitions shall have the same meaning regardless of whether they appear in singular or in plural.

Definitions

For the purposes of this Return and Refund Policy:

• Company (referred to as either “the Company”, “We”, “Us” or “Our” in this Agreement) refers to Prickhome Technologies Private Limited, Jain Sthaanak Streetn Near Old Anaj Mandi, Gohana, Dist. Sonipat, Haryana, 131301
• Goods refer to the items offered for sale on the Service.
• Orders mean a request by You to purchase Goods from Us.
• Service refers to the Website.
• Website refers to Prickhome Technologies, accessible from https://swarnjal.com/
• You means the individual accessing or using the Service, or the company, or other legal entity on behalf of which such individual is accessing or using the Service, as applicable.

Your Order Cancellation Rights

You are entitled to cancel Your Order within 10 days without giving any reason for doing so.

The deadline for cancelling an Order is 10 days from the date on which You received the Goods or on which a third party you have appointed, who is not the carrier, takes possession of the product delivered.

In order to exercise Your right of cancellation, you must inform Us of your decision by means of a clear statement. You can inform us of your decision by:

• By email: [email protected]
• By visiting this page on our website:https://swarnjal.com/
• Calling/WhatsApp :- +91-9050526154

We will reimburse You no later than 10 days from the day on which We receive the returned Goods. We will use the same means of payment as You used for the Order, and You will not incur any fees for such reimbursement.

Conditions for Returns

For the Goods to be eligible for a return, please make sure that:

• The Goods were purchased in the last 10 days
• The Goods are in the original packaging
• If our products are purchased from other E-commerce platforms e.g. Amazon, Flipkart, Ebay, Meesho, Jio Mart, etc. then commission charged by the other platform will be deducted from refund.

The following Goods cannot be returned:

• The supply of Goods made to Your specifications or clearly personalized.
• The supply of Goods which according to their nature are not suitable to be returned, deteriorate rapidly or where the date of expiry is over.
• The supply of Goods which are not suitable for return due to health protection or hygiene reasons and were unsealed after delivery.
• The supply of Goods which are, after delivery, according to their nature, inseparably mixed with other items.

We reserve the right to refuse returns of any merchandise that does not meet the above return conditions in our sole discretion.

Returning/Replacement/Guarantee/Service of Goods

You are responsible for the cost/ expenses and risk of returning the Goods to Us. You shall send the goods to us at the address mentioned on bill or suggested by us.

After receiving the product, replacement process will be initiated. We cannot be held responsible for Goods damaged or lost in return shipment. Therefore, we recommend an insured and traceable mail service. We are unable to issue/send a refund or replacement without actual bill receipt & Shipping Receipt of the Goods or proof of received return delivery. Customer shall also bear the Expenses which is incurred during the sending/shipping of the replaced or serviced product back from service center of the company to Customer, be it in guarantee period or out of the guarantee period.

6+6 Months Guarantee: 6+6 Guarantee means that First 6 Months guarantee is by default. After Registering the product within prescribed time, it is set as the stand ardor normal option without doing anything. After first 6 Months, to get next 6 Months period Guarantee which will make Total 1 year Guarantee You need to send the coupon code & proceed as per the Instructions within prescribed time. After this process you will get total 1 Year guarantee.

Contact Us

If you have any questions about our Returns and Refunds Policy, please contact us:

• By email: [email protected]
• By visiting this page on our website: https://swarnjal.com/
• Calling/ WhatsApp  :- +91-9050526154
  Note: All disputes are subject to Gohana (Dist. Sonipat) jurisdiction only.

References

• PrickHome Technologies
• Return & Refund Policy Generator - Privacy Policies

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>