Sensorworx SWX-823-WH 0-10V Dimming Wall Switch User Manual

: June 13, 2024
: SENSORWORX

Table of Contents

Sensorworx SWX-823-WH 0-10V Dimming Wall Switch
Product Information
Product Usage Instructions
OVERVIEW
SPECIFICATIONS
FEATURES
WIRING
INSTALLATION
ORDERING INFO
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sensorworx SWX-823-WH 0-10V Dimming Wall Switch

Product Information

Catalogue Number: [Insert Catalog Number]
Date: [Insert Date]
Project: [Insert Project Name]
Product Name: 0-10V Dimming Wall Switch
Product Type: Line Voltage Wall Switch Dimmer
Overview: The SWX Wall Switch Dimmer is a linevoltage wall switch that allows for 0-10V dimming control.

Features:

Electrical Features
Physical Features
Cover Plate

Specifications:

Electrical:
- Operating Voltage: 120-277 VAC Single Phase, 50/60 Hz
- Load Ratings:
- Max: 800W @ 120VAC, 1200W @ 277VAC
- Min: None
- Load Types: LED Driver/Lamps, CFL, Electronic/Magnetic Ballasts (Fluorescent), Tungsten (Incandescent)
- Dimming Compatibility: 0-10 VDC ballasts or drivers compliant with IEC 60929 Annex E.2
- Dimming Load: 50 mA maximum (sink only)
Environmental:
- Physical Size: 2.74H x 1.68W x 1.39D (6.96 x 4.27 x 3.53 cm)
- Not Including Mounting Strap

Product Usage Instructions

To use the 0-10V Dimming Wall Switch, follow these steps

Turn off the power supply to the switch at the circuit breaker.
Remove the existing wall switch plate cover.
Disconnect the wires from the old switch and remove it from the wall.
Take the SWX Wall Switch Dimmer and align it with the electrical box.
Connect the wires from the electrical box to the corresponding terminals on the dimmer switch.
Securely fasten the dimmer switch to the electrical box using the provided screws.
Attach the cover plate to the dimmer switch.
Restore power to the switch at the circuit breaker.
The 0-10V Dimming Wall Switch is now ready for use.

Note: Ensure that all connections are properly secured and that the load does not exceed the specified ratings for the dimmer switch.

OVERVIEW

The SENSORWORX line voltage wall switch & 0-10 volt dimmer provide a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trim, Turn on Levels, and Curve Types. This dimmer also matches the SENSORWORX family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.

SPECIFICATIONS

ELECTRICAL
OPERATING VOLTAGE
- 120-277 VAC SINGLE PHASE, 50/60 Hz
LOAD RATINGS
MAX: 800W @ 120VAC
- 1200W @ 277VAC
MIN: None
LOAD TYPES
- LED Driver/Lamps
- CFL, Electronic/Magnetic Ballasts (Fluorescent)
- Tungsten (Incandescent)
DIMMING COMPATIBILITY
- 0-10 VDC ballasts or drivers compliant with IEC 60929 Annex E.2
DIMMING LOAD
- 50 mA maximum (sink only)
ENVIRONMENTAL
OPERATING TEMP
- 32°F to 122°F (0°C to 50°C)
RELATIVE HUMIDITY
- 0-95% Non-Condensing, Indoor Use Only
PHYSICAL
SIZE
- 2.74”H x 1.68”W x 1.39”D
- (6.96 x 4.27 x 3.53 cm)
- Not Including Mounting Strap <1” Wallbox Mounting Depth
WEIGHT
- 4.5 oz
MOUNTING
- Single Gang Switch Box

FEATURES

ELECTRICAL FEATURES
Accommodates Neutral (3-Wire) and No-Neutral (2-Wire) Installation
Electronically Timed Switching Ensures Long Relay Life
Works both Standalone and with 3-Way Switches
Meets NEC 404.2(c) & 404.22 Guidelines Regarding Powering Over Ground & Current Leakage

PHYSICAL FEATURES

Enclosure is 25-40% Shallower than Other Dimmers (< 1” Depth into Wallbox)
Self-Grounding Mounting Strap
Modern Look and IntuitiveEasy-Tap Buttons for On/Off, Raise, & Lower
Settings are Adjustable Without Removing the Cover Plate

OPERATIONAL FEATURES

5 LED Dimming Level Indication
Configurable Dimming Parameters including High/Low Trims, Turn on Levels, and Curve Types
Blue Locator LED when Lights are OffLINE

WIRING

The unit works both in installations where a Neutral connection is available as well as in installations where only a Ground connection is present.
If no neutral is present, remove the white sleeve from the wire & connect the now Green/Yellow wire to the Ground.
Note, that either the white wire or green/yellow wire must be connected. The all-green wire is just for safety.

3-WAY WIRING

Note: if used in the 3-way or 4-way application, the SWX-823 unit must be wired as the last device before the lighting load.

NOTE: This product is UL-listed and meets NEC 404.2(c) & 404.22 guidelines regarding powering over ground & current leakage. Powering over ground is permitted for replacement/retrofit only

NEUTRAL TO GROUND CONVERSION DETAIL

The white wire has a removable sleeve which reveals a green/yellow wire

INSTALLATION

FRONT

SIDE

THE SENSOR FACE IS FIELD REMOVABLE IN ORDER TO CHANGE COLORS. CONTACT THE FACTORY FOR ADDITIONAL FACES

ORDERING INFO

PRODUCT DESCRIPTION

PRODUCT DESCRIPTION	COLOR 1	PACKAGE COUNT
SWX-823 Line Voltage Switch & Dimmer (0-10V)	White Ivory

Light Almond Gray

Red Black

| – WH

– IV

– LA

– GY

– RD

– BK

| Single Pack 10 Pack 2| Blank

– J10

NOTE 1: WALLPLATE NOT INCLUDED
NOTE 2: THE CONTRACTOR PACK OPTION (-J10) REDUCES JOB SITE WASTE AND INVENTORY TIME

ACCESSORY	COLOR
SWX-199 Single Gang Wall Plate	White Ivory

Light Almond Gray

Red Black

| – WH

– IV

– LA

– GY

– RD

– BK

OPERATION SETTINGS

HIGH-END & LOW-END TRIM

High-end trim enables energy-saving task tuning by setting a maximum level (100%-50%, or Custom) at which users are allowed to raise lights
Low-end trim sets a minimum level at which users are allowed to lower lights (0%-50%, or Custom)

TURN ON/TURN OFF DIMMING OPERATION

Lighting turns on to the last user level or a preset level (100%, 50%, or custom)
The switch can turn off lighting by switching off power (by opening the relay) or dimming below the electronic off-level
Lighting can also be held at low-end trim level during off-state

FADE ON / FADE OFF RATES

Adjustable time for level to ramp up to turn-on level (0.75 sec, 1.5 sec, 3 sec, 5 sec, or 15 sec)
Adjustable time interval for level to ramp down to off (0.75 sec, 1.5 sec, 3 sec, 5 sec, or 15 sec)

DIMMING CURVE

The dimming curve defines how dimmers adjust their voltage output in response to button commands
Linear (default), Square Log

LED FUNCTIONALITY

5 White LED(s) show level when lights are on or for 2 seconds after any adjustment
Blue LED serves as a switch locator when lights are off
LED functionality can be disabled