CHAUVET CP Rack CPRACK B and H Photo Video User Guide

: June 13, 2024
: Chauvet

Table of Contents

CHAUVET CP Rack CPRACK B and H Photo Video
Product Information
Product Usage Instructions
Safety Notes
QUICK REFERENCE GUIDE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CHAUVET CP Rack CPRACK B and H Photo Video

Product Information

Product Name: CP Rack
Model ID: CPRACK
Languages: English, Spanish (ES), French (FR), German (Deutsch), Dutch (Nederlands)

Safety Notes

Critical: These instructions must be followed to ensure proper installation, configuration, and operation of the CP Rack. Failure to do so may result in product malfunction, damage, or harm to the operator.
Important: This information is crucial for correct installation and configuration. Failure to follow these instructions may affect the functionality of the product.
Useful: Additional information that may be helpful during installation and use of the CP Rack.

Product Overview

Component	Quantity
Tube with clamps	4
Adjustable H frame	2
Side rails	2
Base	8
Safety pin	1
Screw with washers and nut	4

Product Usage Instructions

Setup

To begin setup
- Raise each side rail of the CP Rack by removing the pins at the base of each side rail. To remove the pin, first remove the safety clip.
- Insert the pin to lock the side rail into an upright position.
- Insert the safety clip into the pin.
- Repeat steps 1-3 with all bases to lock the side rails.
- Ensure that all attachment points are fully tightened to avoid safety hazards.
To detach the tubes from bases
- Release the clamp by depressing the switch.
- Remove the tube.
- Repeat the process with the other clamp to release the tube completely.
To connect the tube(s) to the H frames
- Ensure that the clamp is facing down and press the clamp onto the horizontal bar of the H frame.
- Ensure that the clamp is firmly attached to the H frame.
- Repeat the previous steps with any other desired tubes.
- Do not exceed the maximum load capacity of 1,000 lbs to avoid safety hazards.
To extend the H frames
- Remove safety clips locking the H frame in place.
- Extend or lower the pin to the desired height.
- Re-insert the safety clips and pins to stabilize the H frames at the desired height.
- The maximum stacking height is 2 CP Racks.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance of the CP Rack.

DO NOT
Leave outdoors in locations with extreme environmental conditions. This includes, but is not limited to
Exposure to a marine/saline environment (within 3 miles of a saltwater body of water).
Locations where normal temperatures exceed the temperature ranges in this manual.
Locations that are prone to flooding or being buried in snow.
Other areas where the product will be subject to extreme radiation or caustic substances.
In the event of a serious operating problem, stop using immediately.

What is Included

CPRack
Cover
Quick Reference Guide

Symbols

Symbol	Meaning
Critical installation, configuration, or operation information. Not

following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
| Important installation or configuration information. The product may not function correctly if this information is not used.
| Useful information.

QUICK REFERENCE GUIDE

Product Overview

$CHAUVET-CP Rack-CPRACK-B and-H-Photo Video $1$$ Setup

To begin setup
- Raise each side rail of the CP Rack by removing the pins at the base of each side rail.
- b. To remove the pin, remove the safety clip first.
- c.
- d. $CHAUVET-CP Rack-CPRACK-B and-H-Photo Video $5$$
- e. It is possible to remove both of the H frames from the CP Rack. The H frames may then be hung from a truss.
- f. Insert the pin to lock the side rail into upright position.
- g. Insert the safety clip into the pin.
- h. Repeat steps 1-f and 1-g with all bases to lock the side rails. Warning! Ensure that all attachment points are fully tightened. Failure to do so may cause safety hazards!

To detach the tubes from bases

a. Release the clamp by depressing the switch.
b. Remove the tube.
c. Repeat the process with the other clamp to release the tube completely.

To connect the tube(s) to the H frames

a. Ensure that the clamp is facing down and press the clamp onto the horizontal bar of the H frame.
b. Ensure that the clamp is firmly attached to the H frame.
c. Repeat the previous steps with any other desired tubes: The maximum load capacity for this product is 1,000 lbs. Do not exceed this weight, as failure to do so may cause safety hazards.

It is possible to extend the H frames to double the height of the CP Rack. To extend the H frames

a. Remove safety clips locking H frame in place.
b. Extend or lower the pin to the desired height.
c. Re-insert the safety clips and pins to stabilize the H frames at the desired height. It is possible to stack another CP Rack on top of this product. Maximum stacking is 2 products high.

Contact Us

Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U. K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.

General Information Technical Support
Chauvet World Headquarters