PLANET FGSD-1821P Fast Ethernet PoE Switch User Manual

: June 13, 2024
: PLANET

Table of Contents

PLANET FGSD-1821P Fast Ethernet PoE Switch
Product Information
Product Usage Instructions
1000BASE-X SFP Port
Package Contents
Hardware Introduction
- LED Indicators
Hardware Installation
Product Specifications
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PLANET FGSD-1821P Fast Ethernet PoE Switch

PLANET-FGSD-1821P-Fast-Ethernet-PoE-Switch-PRODUCT

Product Information

Thank you for purchasing the PLANET 16-/24-Port 10/100TX 802.3at PoE + 2-Port 10/100/1000T + 1-Port shared 1000X SFP Desktop Switch, FGSD-1821P or FGSD- 2621P. The 802.3at PoE+ Switch mentioned in this Guide refers to the FGSD- 1821P or FGSD-2621P.

The package contents include:

The 802.3at PoE+ Switch x 1
User’s Manual x 1
Power Cord x 1
SFP Dust Cap x 1
Screws x 8
Rack-mounting Brackets x 2
Rubber Feet x 4

If any of these pieces are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing material to repack the product in case there is a need to return it for repair.

Product Usage Instructions

LED Indicators

The LED indicators on the switch provide information about the status of each port:

Per 10/100BASE-TX Port

LED	Color	Function
10/100 LNK/ACT	Green	Lights to indicate the link through that port is

successfully
established. Blinks to indicate that the Switch is actively sending
or receiving data over that port.
PoE in Use| Amber| Lights to indicate the port is providing PoE DC in-line
power.

Per 10/100/1000BASE-T Port

LED	Color	Function
LNK/ACT	Green	Lights to indicate the link through that port is successfully

established. Blinks to indicate that the Switch is actively sending
or receiving data over that port.

1000BASE-X SFP Port

LED	Color	Function
1000 LNK/ACT	Green	Lights to indicate the link through that port is

successfully
established at 1000Mbps. Blinks to indicate that the Switch is
actively sending or receiving data over that port.

VLAN Modes

The switch supports different VLAN modes:

Standard Mode (default)

In this mode, all ports are in the same VLAN.

VLAN Isolation Mode

In this mode, ports 17~18 and the SFP Port are isolated from Ports 1~16. Access is permitted between Ports 17~18 and the SFP Port.

Extend Mode

In this mode, ports 1 to 8 can extend the transmission distance up to 250 meters (820 feet).

Hardware Installation – Rack Mounting

To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow these instructions:

Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side.
Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch using the supplied screws.

Caution: Use only the supplied screws with the mounting brackets to avoid damage that could invalidate the warranty.

Package Contents

Thank you for purchasing PLANET 16-/24-Port 10/100TX 802.3at PoE + 2-Port 10/100/1000T + 1-Port shared 1000X SFP Desktop Switch, FGSD-1821P or FGSD-2621P. “802.3at PoE+ Switch” mentioned in this Guide refers to the FGSD-1821P or FGSD-2621P
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should contain the following items
If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Hardware Introduction

Front Panel

The front panel of the 802.3at PoE+ Switch consists of 16/24 auto-sensing 10/100BASE-TX RJ45 ports, 2 auto-sensing 10/100/1000BASE-T RJ45 ports and 1 1000BASE-X SFP port.
The LED Indicators are also located on the front panel of the 802.3at PoE+ Switch.

LED Indicators

System

LED	Color	Function
PWR	Green	Lights to indicate the Switch has power.

PoE (max.)

|

Green

| Off to indicate the PoE power is less than 80% of total power.

Lights to indicate the PoE power is above 80%.

Per 10/100BASE-TX Port

LED	Color	Function

10/100

LNK/ACT

|

Green

| Lights to indicate the link through that port is successfully established.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

PoE in Use| Amber| Lights to indicate the port is providing PoE DC in- line power.

Per 10/100/1000BASE-T Port

LED	Color	Function

10/100/1000

LNK/ACT

| ****

Green

| Lights to indicate the link through that port is successfully established.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

1000BASE-X SFP Port

LED	Color	Function

1000

LNK/ACT

| ****

Green

| Lights to indicate the link through that port is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

Multiple Functions of DIP Switch

The front panel of the 802.3at PoE+ Switch provides one DIP switch for Standard, VLAN or Extend mode selection. The detailed descriptions are shown in the following table.

Note

Please select a DIP switch mode before powering on the 802.3at PoE+ Switch.

PLANET-FGSD-1821P-Fast-Ethernet-PoE-Switch-FIG-2

Rear Panel

The rear panel of the 802.3at PoE+ Switch indicates an AC power socket, which accepts input power from 100 to 240V AC, 50-60Hz, 5A. PLANET-FGSD-1821P-Fast-
Ethernet-PoE-Switch-FIG-5

AC Power Receptacle

Power Notice

The device is a power-required device, which means it will not work till it is powered. If your networks should be active all the time, please consider using UPS (uninterrupted power supply) for your device. It will prevent you from network data loss or network downtime.
In some areas, installing a surge suppression device may also help to protect your 802.3at PoE+ Switch from being damaged by unregulated surge or current to the 802.3at PoE+ Switch or the power adapter.

Hardware Installation

Rack Mounting

To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below.
Step 1: Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+Switch with supplied screws attached to the package. Figure 3-1 shows how to attach brackets to one side of the 802.3at PoE+ Switch.
Caution You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 3-2.
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at complied PDs and other network devices.
A. Connect one end of a standard network cable to the 10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at PoE+ Switch.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers, etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall outlet.
When the 802.3at PoE+ Switch receives power, the power LED should remain solid Green.

Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP port of the 802.3at PoE+ Switch.
The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the 802.3at PoE+ Switch, as Figure 3-3 shows.

Approved PLANET SFP Transceivers

PLANET 802.3at PoE+ Switch supports both single mode and multi-mode SFP transceivers. The website link of ap-proved PLANET SFP transceivers is shown below: https://www.planet.com.tw/en/product/mgb-series-transceiver.
It is recommended to use PLANET SFP on the 802.3at PoE+ Switch. If you insert an SFP transceiver that is not supported, the 802.3at PoE+ Switch will not recognize it.

Before we connect the 802.3at PoE+ Switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASESX; 1000BASE-LX to 1000BASE-LX.
Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
- To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male duplex LC connector type.
- To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male duplex LC connector type.

Product Specifications

Model	FGSD-1821P	FGSD-2621P

Hardware Specifications
10/100BASE-TX

RJ45 Port with 802.3af/802.3at PoE+ Inject

| ****

16

| ****

24

10/100/1000BASE-T

RJ45 Port

| 2 (Port-17 shared with SFP port)| 2 (Port-26 shared with SFP port)
1000BASE-X SFP/

mini-GBIC Slot

| 1

(shared with Port-17)

| 1

(shared with Port-26)

DIP Switch

| Selectable operation mode

n Standard

n VLAN

n Extend

Dimensions (W x D x H)| 280 x 180 x 44 mm (1U height)
Enclosure| Metal
Weight| 1800g| 1870g
Power Requirements| 100~240V AC, 50/60Hz, 5A max.
Power Consumption/ Dissipation| Max. 207 watts/706 BTU| Max. 217 watts/740 BTU
Thermal Fan| 1
ESD Protection| Contact discharge of ±6KV DC, Air discharge of ±8KV DC
Surge Protection| Differential Mode ±4KV, Common Mode ±6KV
Installation| Desktop or rack-mount installation
---|---

LED

| System

Power (Green) PoE Max. (Green)

10/100/1000T RJ45 Interfaces

10/100/1000 LNK/ACT (Green)

PoE-in-Use (Amber)

1000X SFP Interfaces

1000 LNK/ACT (Green)

15.4 watts

| 12| 12
---|---|---
Number of PDs, 30 watts| 6| 6
Standards Conformance
Regulatory Compliance| FCC Part 15 Class A, CE

Standards Compliance

| IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3z Gigabit SX/LX

IEEE 802.3x flow control and back pressure

IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy-Efficient Ethernet

Environment

Operating

| Temperature: 0 ~ 50 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Storage

| Temperature: -10 ~ 70 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Customer Support

Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.
PLANET online FAQs: https://www.planet.com.tw/en/support/faq
Support team mail address support@planet.com.tw
Copyright © PLANET Technology Corp. 2022
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

PLANET Technology Corp.

10F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan 2351-AK3380-002

Warning:

This device is compliant with Class A of CISPR 32.
In a residential environment this device may cause radio interference.

Energy Saving Note of the Device

This power required device does not support Standby mode operation. For energy savings, please remove the power cable to disconnect the device from the power circuit.
Without removing the power cable, the device will still consume power from the power source. In view of Saving the Energy and reducing the unnecessary power consumption, it is strongly suggested to remove the power cable from the device if this device is not intended to be active.