VIGITRON Vi30005 5-Port 1G PoE Powered PoE Switch Instruction Manual
- June 13, 2024
- VIGITRON
Table of Contents
- Vi30005 5-Port 1G PoE Powered PoE Switch
- Important Safety Warning
- Application Drawing
- IP Camera-end Installation
- PoE Switch/PoE Midspan end Installation
- Technical Specifications*
- Drawings
- Status LEDs
- Ordering Information
- Limited Lifetime Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Vi30005 5-Port 1G PoE Powered PoE Switch
Installation Manual
Vi30005 5-Port 1G PoE Powered PoE Switch
The MaxiCollector Vi30005 is a revolutionary five port 1G Powered PoE switch.
The Vi30005 can accept PoE power from an external source and provide PoE to
all four ports. This eliminates the need for local power supplies and outlets,
and lowers installation costs.
The Vi30005’s plug-and-play eliminates the need for IP addressing. The four
Ethernet port can be directly connected to any IP address and will pass that
device’s IP address. Network pre-programmed switching features include 802.1p
QoS priority queuing, port based VLAN, MAC addressing up to 2K full and half
duplex operation compliant to 802.3x standards and automatic address learning
and aging.
The Vi30005 takes full advantage of high bandwidth maintaining 10/100/1000Mbps
transmission with minimum transmission error and latency by employing full
layer 2 network switching technology. The Vi30005 can be used to connect to
multiple remote network devices such as Megapixel IP cameras, VoIP telephone
systems, or wireless transmitters.
Using the Vi1120, 120 watt 57 volt power supply, and any MSA compliant fiber
SFP, the Vi30005 can transmit four cameras over distance of 80Km while
providing 30 watts per port and up to 60 watts for two port using the Vi0015
combining cable.
Important Safety Warning
– Read and keep these instructions.
– Heed all warnings.
– Follow all instructions.
– Do not use this apparatus near water.
– Clean only with a dry cloth.
– Install in accordance with the manufacturer’s instructions.
– This installation should be made by a qualified service person and should
conform to all local codes.
– DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
– To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
– No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
– DO NOT install the unit in a place where the operating ambient temperature
exceeds 75°C or is below – 40°C.
– Make sure that the external power supply output voltage is in the
recommended range.
– Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including DVRs) that produce heat.
– Protect the power cord from being walked on or pinched particularly at power
source, convenience receptacles, and the point where they exit from the
apparatus.
– Only use attachments/accessories specified by the manufacturer.
– Unplug this apparatus during lightning storms or when unused for long
periods of time.
– Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as when a power supply
cord or plug is damaged, liquid has been spilled, objects have fallen inside
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
– The main plug is used as the disconnect device and shall remain readily
operable. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING! – To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! – This apparatus is a Class I product. This product must be
connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! – The mains plug is used as the disconnect device and shall
remain readily operable.
Application Drawing
Powering the Vi30005 and 4 remote cameras using PoE The Vi30005 is a PoE powered PoE switch that can be used to
power up to four cameras using PoE.
Connecting the Vi30005 and 4 remote cameras over Fiber Optics The Vi30005 can be used to connect to up to 4 cameras at
distances up to 80Km over fiber optics.
IP Camera-end Installation
UTP Uplink w/ Remote PoE:
– Connect the network cable coming from the PoE switch or PoE Midspan to the
uplink Ethernet port at rear of Vi30005.
– Plug in the IP/PoE devices to the four ports one the Vi30005’s front panel.
– Set 30W/60W based on the type of the remote PoE source
PoE Power is allocated based on the required port power up to 36W starting
with Port 1 having the highest priority. Once the total sum of the PoE power
is allocated no more power will be available to remaining ports.
UTP Uplink w/ Local Power Supply:
– Connect the network cable coming from the PoE switch or PoE Midspan to the
fifth Ethernet port at rear of Vi30005.
– Plug in the IP/PoE devices to the four ports one the Vi30005’s front panel.
– Connect the approved local power supply to the power connector of Vi30005.
Fiber SFP Uplink:
Note: The SFP (small format pluggables) must be the same types at both
ends of the fiber cable and must match the fiber cable requirements.
– Plugin the SFP to the SFP socket of Vi30005.
– Connect the fiber cable to the SFP.
– Connect the Vi1120 power supply to the Vi30005 power connector.
Individual ports will be able to provide up to 36W. If more power needed for
approved IP devices use the Vi00016 combination cable to combine two ports.
Starting with ports 1 and 2, connect the IP device to the Ethernet ports of
the Vi00016 cable.
PoE Switch/PoE Midspan end Installation
UTP link:
– Connect the network cable coming from the Vi30005 Uplink port to one of the
Ethernet ports of the PoE switch or PoE Midspan.
Fiber SFP Link:
– Connect the fiber cable to the SFP port of the network switch.
The SFP must be the same types at both ends of the fiber cable and must match
the fiber cable requirements.
Technical Specifications*
Electrical
Ethernet Interface | Standard 10/100/1000BaseT |
---|---|
Fiber Optics | 1G, SFP socket, depends on the SFP & fiber type |
Power Supply | 48-57VDC @ 2A min. for 802.3 at 30W / port |
Connectors | Ethernet Interface: 5 x RJ-45 Connector |
Fiber Optics: SFP Socket
Power: Round 2.5mm cpower onnector
RFC| 2544 TCP/IP Packet Transmission
768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet
Compatible with| IEEE 802.3af PoE, IEEE 802.3at PoE
Environmental
Humidity | 0 to 95%, non-condensing |
---|---|
Temperature | Operating: -40°C to +75°C |
Storage: -40°C to +85°C
Mechanical
Dimensions | 1.2×3.75×5.1 in., 3.0×9.53×13 cm (HxWxL) |
---|---|
Weight | 0.70 lb (317.5 g) |
Material | Aluminum |
Accessories
56VDC, 120W External power supply (optional)
*Specifications subject to change without notice.
Drawings
Status LEDs
LED Name | Color | Status | Function |
---|---|---|---|
Power | GREEN | OFF | Power is OFF |
ON | Power is ON | ||
PoE | GREEN | OFF | PoE is OFF |
ON | PoE is ON | ||
Link/Activity | GREEN | OFF | No connection |
ON / FLASHING | Connection is OK, Traffic | ||
1G | ORANGE | OFF | 10/100 |
ON | 1G |
Ordering Information
Part No. Description
Vi3005 | 5-port PoE Layer 2 Network Switch |
---|
Limited Lifetime Warranty
Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in
accordance with these instructions, will be free of defects in material and
workmanship for lifetime defined as the duration period of time until product
end of life is announcement. After which Vigitron will continue to provide
warranty services for a period of 3 years. Period covering valid warranty will
be determined by proof of purchase in the form of an invoice from an
authorized Vigitron dealer.
Warranty will only be provided for as long as the original end user purchaser
owns the product. Warranty is not transferrable. At Vigitron’s option,
defective product will be repaired, replaced or substituted with a product of
equal value. This warranty does not apply if, in the judgment of Vigitron,
Inc., the Product fails due to damage from shipment, handling, storage,
accident, abuse or misuse, or if it has been used or maintained not conforming
to Product manual instructions, has been modified, or serial number removed or
defaced. Repair by anyone other than Vigitron, Inc. or an approved agent will
void this warranty. Vigitron, Inc. shall not under any circumstances be liable
to any person for any incidental, indirect or consequential damages, including
damages resulting from use or malfunction of the product, loss of profits or
revenues or costs of replacement goods. The maximum liability of Vigitron,
Inc. under this warranty is limited to the original purchase price of the
Product only.
Prior to returning any defective Product, the end customer or the reseller
from whom the end customer originally purchased the Product must obtain a
Return Materials Authorization (RMA) number from Vigitron, Inc. All defective
Products should be returned to Vigitron, Inc. with shipping charges prepaid.
No collect shipments will be accepted.
The Smart Choice for Transmission Solutions
www.vigitron.com
TEL (+1) 858 – 484 – 5209
FAX (+1) 858 – 484 – 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA
support@vigitron.com
www.vigitron.com
© Copyright 2022 Vigitron, Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>