fubag 120105 Air Tool Set User Manual

fubag 120105 Air Tool Set User Manual

WARNING! BEFORE USINGAIR PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY.
ONLY QUALIFIED AND WELL-TRAINED STAFF ACQUAINTED WITH THE MANUAL CAN USEAND OPERATE THIS TOOL.

The operation manual contains the description, safety rules and all the information necessary for proper maintenance of FUBAG pneumatic tool. Please keep the operation manual and refer to it in case of any questions concerning safety operation, maintenance, storage and transportation of FUBAG tool. Nonobservance of the indicated recommendations may cause the damage of the tool and injuries of the user.

Safety rules

• General safety requirements are to conform to EN 792-9.
• Only the persons who have taken the preliminary training and are aware of the tool structure, safety rules and the requirements of the operation manual can operate the tool.
• Vibration characteristics of the tool correspond to EN ISO 8662-1 requirements. The use of the tool is not allowed for the operations when vibration levels exceed the values established by EN ISO 8662-1.
• Noise characteristics of the tool correspond to EN ISO 11202 requirements. The corrected level of the noise power does not exceed 99 dBA. The use of the tool is not allowed for the operations when noise levels exceed the values established by EN ISO 11202.
• When operating the tool it is strongly recommended to use the protective spectacles, headphones and protective gloves.
• Always keep the steady foot rest in order not to stumble. Always fasten the workpiece with a fixer or a grip to release two hands for operating with the tool.
• Make sure all the clothes fit closely to the body.
• Make sure there are not any foreign objects in the place of operation; and there are not any people in the proximity of the operating tool.
• The workplace is to be aired well.
• Make sure the tool is in OFF position before connecting the air hose.
• Always disconnect the tool from the aerial system when it is not used.
• Do not pull the hose when transporting the tool.

Danger:

• Do not direct the pneumatic tool or flow of the compressed air at the people, animals or your own body. Wear protective spectacles in order to avoid small particles of the dust to get into your eyes together with the flow of the compressed air.
• Do not direct the flow of the compressed air at the compressor.
• Do not work without any protective footwear. Do not touch the operating compressor with wet hands and/or feet.
• Do not exceed the recommended operating pressure.
• Do not fix, disassemble or carry out any other maintenance operations without disconnecting the tool from the air channel.
• Do not use the spare parts of the other manufacturers. Always use only original spare parts

Caution:

• When connecting the pneumatic tool to the compressor hose always block the air escape cock.
• Always follow the safety rules when using the compressed air.
  If revealing any faults immediately discontinue the operation.

Description

The pneumatic tool kit is for different operations with the use of compressed air as an energy source. The kit consists of:

• Impact with the tail 1/2″.
• Tire inflation gun

Technical Specifications

The manufacturer reserves himself the right to make the manual’s content or function change without any preliminary notification of the users.

Connection and operation

It is necessary to re-activate the tool before the operation start. To re- activate the tool pour the pure paraffin through the inlet connecting pipe when the trigger is open, then blow the tool through with the dry compressed air. Repeat it 2 or 3 times.
The system of the compressed air lead-in to the tool is in the below diagram.

• Before the first putting the tool into operation it is necessary to pour in 5 10 ml of the machine oil as per specification SAE#10 or its analog through the connecting pipe of the compressed air lead-in. Blow the air hose through. Connect it to the tool, press the starting lever and operate the tool at no load running within 2-3 minutes.After it release the starting lever.
• If the lubricator is not used during the operation it is necessary to pour 5 10 ml of the machine oil as per specification SAE#10 or its analogue into the inlet connecting pipe of the tool every operating hour.
• Use only recommended oil types.
• Check the thread connection tightening firmness on the housing of the tool periodically during the maintenance – their slackening is not allowed.
• The tool provides fast screwing and unscrewing of the threaded hardware. The heads are to be of the impact type with the corresponding size. Do not use any other head types.
• The moment of the reinforce of the button rotation the values of the moment are indicated around can be adjusted. The lower value denotes little force; the high one denotes high force.
• Make sure the reverse switcher is set up every time before screwing and unscrewing. The symbol “F” denotes screwing, while the symbol “R” stands for unscrewing. Screwing is defined as clockwise rotation.
• Avoid mechanical damages of the tool as it may cause malfunctions or failure.
• Keep the tool clean to provide its proper operation.
• Use the tool according to its intended purpose.

1. Air tool
2. Oil lubricator
3. Pressure governor
4. Filter
5. Closing cock
6. Pressure release cock
7. Conduit
8. Compressor
9. Hose

Troubleshooting

Fault

| Possible causes|

Correction

---|---|---
The tool won’t develop enough power| Insufficient pressure in the air line| Develop the pressure up to 6.3 bar
Blade tear and wear| Change the blades
Slackening of the engine mount| Tighten the screws of the mount (if necessary change the rubber ring)
There is spindle wavering and bang during the operation| Tear and wear of the engine bearings| Change the bearings
When engine rotating the spindle won’t rotate| There is a breakdown in the place of connection of the rotor with the spindle| Change the details worn
The housing is warmed when the engine is running, the spindle won’t rotate| There is no lubrication there| Disassemble the tool, flush the details and lubricate them
Tear and wear or break down of the reducer| Change the details worn out
The engine won’t rotate after the long term storage| Engine blade swelling| Bring the size of the blades to the required one

Transport & Storage

In case of long term work brake it is necessary to keep the tool at the temperature of +5 + 25°С and humidity not more than 70%. It is recommended to pour 10-20 ml of oil into it and blow it through with the minimal pressure.
During transportation and storage of the tool keep it away from damp. The tool should be kept in a dry, well air conditioned place. Do not expose it to damp, corrosive and dangerous gases and dust. After the package is unsealed the tool should be repacked in case of transportation to the workplace or for  storage.

Warranty

Warranty refer to defects of materials and components and do not refer to components subject to natural wear and maintenance work.
Only machines cleaned from dust and dirt in original factory packing fully completed, provided with instruction manual, warranty card with fixed sales date with a shop stamp factory serial number and originals of sales and ware receipt issued by salesman are subjects of warranty. Within the warranty period the service center eliminate free of charge all detected production defects. The manufacturer disclaims warranty and legal responsibilities if nonobservance of the instruction manual by user, unqualified disassembling repair or maintenance of the machine as well does not bear responsibility for caused injury to persons or damages.

Support

Горячая линия FUBAG
тел.: (495) 641-31-31
info@fubag.ru
www.fubag.ru

References

• Фирменный интернет-магазин FUBAG - сварочное, садовое и автогаражное оборудование, пневмоинструмент и камнерезные станки купить в Москве с доставкой по России

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>