SIEMENS SE23HI60CE Dishwasher User Guide

SIEMENS SE23HI60CE Dishwasher

Product Information

The dishwasher is a convenient kitchen appliance that helps to clean and sanitize tableware. It comes with various features and settings to ensure efficient and effective cleaning. Before using the dishwasher, it is important to read the instruction manual and familiarize yourself with the safety information provided.

Overview of Water Hardness Settings

The dishwasher has different water hardness settings that can be selected based on the water quality in your area. Refer to the instruction manual for a table of country-specific units. The water hardness range and corresponding setting values are as follows:

Adding Special Salt

To avoid damage to the dishwasher, special salt should only be added to the designated dispenser just before starting a wash program. Follow these steps to add special salt:

1. Unscrew the lid of the dispenser for special salt and remove it.
2. On initial start-up, fill the dispenser with water.
3. Add the special salt to the dispenser. Do not add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding Rinse Aid

Rinse aid is used to improve drying and prevent water spots on your dishes. Follow these steps to add rinse aid:

1. Press the catch on the lid of the dispenser for rinse aid and lift it.
2. Add rinse aid up to the maximum mark.
3. Close the lid of the dispenser for rinse aid until it clicks into position.

Before using for the first time, read the instruction manual and the safety information it contains.

Short and handy

everything your dishwasher needs.

Settings

Overview of water hardness settings

• You can find an overview of the water hardness values that can be selected here.
• A table of country-specific units can be found in the instruction manual.

Hardness range/ mmol/l/ Setting value

• Soft /0 – 1.1 /H00
• Soft /1.2 – 1.4 /H01
• Medium /1.5 – 1.8 /H02
• Medium /1.9 – 2.1 /H03
• Medium /2.2 – 2.9 /H04
• Hard /3.0 – 3.7 /H05
• Hard /3.8 – 5.4 /H06
• Hard /5.5 – 8.9 /H07

Setting the water softening system

1. Press ⁠.
2. To open the basic settings, press setup 3 sec for 3 seconds.
   • The display shows Hxx.
   • The display shows ⁠set.
3. Press start repeatedly until the right water hardness has been set.
4. To save the settings, press setup 3 sec for 3 seconds.

Using Instructions

Adding special salt

To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid 1 and lift ⁠2.
2. Add rinse aid up to the max mark.
3. Close the lid of the dispenser for rinse aid.
   • The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser.
   • The lid clicks into position.

Programmes

• The programme data has been measured in the laboratory according to European standard EN 60436.
• The consumption figures depend on the programme and additional function selected.
• The runtime will change if the rinse aid system is switched off or rinse aid needs to be added.

How to use your appliance

1. Load the tableware.
   • Only clean tableware that is suitable for dishwashers.
   • Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
2. Add detergent.
3. Switch on the appliance .
4. Select the programme.
5. Start the programme ⁠start.
6. Remove the tableware at the end of the programme.
7. To cancel the programme, press Reset 4 sec. for approx. 4 seconds.
   • The programme is cancelled and ends after approx. 1 minute.

Cleaning

Cleaning filters

1. After each wash check the filters forresidue.
2. Turn the coarse filter anticlockwise 1 and remove the filter system ⁠2.
3. Pull down the micro filter to remove.
4. Press the locking catches 1 together and lift the coarse filter out 2.
5. Clean the filter elements under running water.
6. Re-assemble the filter system.
7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm 1 and pull down to remove 2.
2. Pull up the lower spray arm to remove.
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm.
   • The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any water.
4. Prise off the pump cover using a spoon and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove.
6. Remove any remnants of food and foreign bodies in the area of the impeller.
7. Insert the pump cover 1 and press down ⁠2.
   • The pump cover clicks into position.
8. Install the filter system.

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>