Wind River WR1603MB Matte Black Aeris Job Celling Fan Instructions
- June 13, 2024
- Wind River
Table of Contents
Wind River WR1603MB Matte Black Aeris Job Celling Fan
Product Information
- Product Name : WR1603 SERIES
- Model Number : 340644010252
Components Included
- Wall control with 2 mounting screws and 4 wire nuts (1)
- Wall plate with 2 mounting screws (1)
Electrical Connections
WARNING: HOOK UP IN SERIES ONLY DO NOT CONNECT THE HOT AND NEUTRAL WIRES OF ELECTRIC CIRCUIT TO THE WALL CONTROL – DAMAGE TO THE SWITCH AND POSSIBLE FIRE COULD OCCUR.
Before starting the installation, remember to shut off the power at the
circuit breaker or fuse box.
If your outlet box has a ground wire (green or bare copper), connect the wall
control’s ground wire to it. Otherwise, connect the wall control’s ground wire
directly to one of the screws from the outlet box.
Product Usage Instructions
Installing the Wall Control
- Turn off the power at the circuit breaker or fuse box.
- Carefully tuck the wire connections inside the outlet box.
- Secure the wall control to the outlet box using the two provided screws.
- Attach the wall plate over the wall control and secure it with the two provided screws.
- Restore power to the ceiling fan.
- Test the fan for proper operation.
Using the Wall Control
The fan speed can be adjusted using the 4-speed control on the wall control
- “0” turns the fan off.
- “1” sets the fan to high speed.
- “2” sets the fan to medium speed.
- “3” sets the fan to low speed.
The light on/off button controls the light.
Using the Reverse Switch
The reverse switch, located on the fan motor assembly, is used for changing
the direction of the fan blades
- Slide the switch to the left for warm weather operation.
- Slide the switch to the right for cool weather operation.
Speed| Volts| Amps| Watts| RPM| CFM| N.W.|
G.W.| C.F.
---|---|---|---|---|---|---|---|---
Low|
120
| 0.26| 15.34| 75| 2030|
6.08 kgs (13.38 lbs)
|
7.18 kgs (15.8 lbs)
|
1.3 ft.
Medium| 0.39| 33.4| 120| 3250
High| 0.52| 62.73| 164| 4624
NOTE: These are approximate measures. They do not include amps and wattage used by the light kit.
Safety tips
-
To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
-
All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
-
The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs. Use only UL Listed outlet boxes marked “FOR FAN SUPPORT.”
-
The fan must be mounted with a minimum of 7 ft. clearance from the trailing edge of the blades to the floor.
-
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. -
All setscrews must be checked and retightened where necessary before installation.
WARNING: To reduce the risk of electrical shock or fire, do not use this
fan with any solid-state fan ? speed control device. Please contact with
dealer or Wind River at 855-817-WIND (9463) if using solid-state remote.
WARNING: To reduce the risk of fire, electric shock, or personal injury,
mount the fan to the outlet box marked acceptable for fan support with the
screws provided with the outlet box.
- Downrod assembly (1)
- Mounting bracket (1)
- Canopy (1)
- Canopy cover (1)
- Coupling cover (1)
- Fan motor assembly (1)
- 14W LED assembly(1)
- Fan blade (4)
- Wall control with 2 mounting screws and 4 wire nuts (1)
- Wall plate with 2 mounting screws (1)
- Loose parts bag containing
- A: Machine screw (2)
- B: Wood screw (2)
- C: Fiber washer (2)
- D: Lock washer (2)
- E: Blade screw (13)
- F: Fiber washer (13)
- G: Safety bolt (1)
- H: Nut (1)
- I: Balancing kit (1)
Begin installation
Tools Required : Phillips screw driver; slotted screw driver; pliers;
wire cutters; electrical tape.
MOUNTING OPTIONS
If there isn’t an existing outlet box, then read the following instructions.
Shut the power off at the circuit breaker or fuse box. Secure the outlet box
directly to the building structure. Use appropriate fasteners and building
materials. Only use a U.L. Listed metal outlet box marked “Acceptable for
ceiling fan support” to install the ceiling fan Do not use a plastic outlet
box or other device. Figures 1,2 and 3 are examples of different ways to mount
the outlet box. Note: Please contact with dealer or Wind River at 855-817-WIND
(9463) if you need a longer downrod to maintain proper blade clearance when
installing on a steep, sloped ceiling. To hang your fan where there is an
existing fixture but no ceiling joist, you may need to install a hanger ba as
shown in Fig. 4.
Blade installation
Step 1 : Insert the blades through the slots on the fan motor assembly.
Attach the blades to the fan motor assembly using the blades screws and fiber
washers and tighten them securely.(Fig.5)
Hanging the fan
WARNING: Please use all of the parts hardware and components provided by
Wind River. The use of ? other parts, hardware or components not supplied by
Wind River with the fan will void the Wind River Warranty.
REMEMBER to turn off the power. Follow the steps below to hang your fan properly
- Step 1. Attach the mounting bracket to the outlet box with two screws and washers provided with the outlet box. Make sure the mounting bracket is tight and secured. (Fig.6)
- Stpe 2. Lossen the two set screws from the top coupling of the motor assembly. (Fig. 7)
- Step 3. Remove hanger ball from downrod assembly by loosening set screw, removing the cross pin, and sliding ball off rod. (Fig. 7)
- Step 4. Carefully feed fan wires up through the downrod (Fig. 7). Screw the downrod into the coupling. Insert the saftey bolt through the coupling and attach the nut.Tighten firmly. Tighten set screws.
- Step5. Slip coupling cover, canopy cover, and canopy onto downrod (Fig.7).Carefully re-install hanger ball onto rod being sure that cross pin is in the correct position, set screws are tighten and wires are not twisted. Step 6. Now lift motor assembly into position and place hanger ball into hanger bracket. Rotate until the check groove has dropped into the registration slot and seats firmly. (Fig. 8) Rod should not rotate if this is done correctly.
Electrical connections
WARNING: HOOK UP IN “SERIES ONLY” DO NOT CONNECT THE HOT AND NEUTRAL
WIRES OF ELECTRIC CIRCUIT TO THE WALL CONTROL – DAMAGE TO THE SWITCH AND
POSSIBLE FIRE COULD OCCUR.
REMEMBER to shut the power off at the circuit breaker or fuse box. Follow
the steps below to connect the fan to your house supply wires. Use the wire
nuts supplied with your fan. Secure the wire nuts by wrapping the connection
with electrical tape.
Proceed to make the wire conventions as follows
- Set the knob of light on the wall control in the “OFF” position and set the knob of speed on the wall control in the “- ”position. (Fig.9)
- Make wire connections (Fig.9) and secure with wire nuts supplied.
- Black wire from fan to black wire marked “To motor L” from speed control.
- Black wire marked “AC in L” from speed control to black wire from the A/C supply source.
- White wire from fan to white wire from the A/C supply source.
- Blue wire from fan to red wire marked “for light” from light control through a red wire which is shown in Fig.3, The red wire may be a different color depending on your location if your unsure please consult with a qualify electrician.
- Connect the fan ground wire (green) to the household ground wire.
If your outlet box has a ground wire (green or bare copper) connect the wall control’s ground wire to it; otherwise connect the wall control’s ground wire directly to one of the screws from the outlet box.
Installing the wall control
Remember to shut the power off at the circuit breaker or fuse box.
- Carefully tuck the wire connections inside the outlet box. Secure the wall control with the two screws provided. (Fig.10)
- Attach the wall plate over the wall control and secure with the two screws provided.
Finishing the installation
- Step 1. Remove one screw from the mounting bracket and loosen the other screw approximately 1/4 turn. Step 2. Carefully raise the canopy up to the mounting bracket, and ensure the loosened screw is inserted into the key hole on the canopy. Rotate the canopy clockwise. (Fig.11 )
- Step 3. Secure the canopy by replacing the screw previously removed and tightening the screw previously loosened. (Fig.11 )
- Step 4. Place the canopy cover on the canopy, and rotate the canopy cover clockwise until it locks into position. (Fig.11 )
Installing the light kit
- Step 1. While holding the 14W LED assembly under your fan, firmly snap the wire connection plugs together. (FIG. 12)
- Step 2. Attach the 14W LED assembly to the switch box by twisting tightly.
Operation
- Restore power to ceiling fan and test for proper operation.
- Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans, etc.
- Turn on the power and check the operation of your fan.
The fan 4-speed control is used to set the fan speed as follows (Fig.13)
- = Turns the fan off
- = High Speed
- =Medium Speed
- = Low Speed
The “ ” button will control the light on or off.
The Reverse switch is located on the fan motor assembly (Fig.14).
Slide the switch to the Left for warm weather operation. Slide the switch to
the Right for cool weather operation.
NOTE: Wait for the fan to stop before reversing the direction of the blade rotation.
Warm weather – (Counterclockwise Direction) A downward air flow creates a cooling effect. This allows you to set your air conditioner on a higher setting without affecting your comfort. (Fig.15) Cool weather – (Clockwise Direction) An upward air flow moves warm air off the ceiling. This allows you to set your heating unit on a lower setting without affecting your comfort. (Fig. 16)
Care and Cleaning
- Check the support connections, brackets, and blade attachments twice a year. Ensure they are secure. Because of the fan’s natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling.
- Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
- (Optional) Apply a light coat of furniture polish to the wood blades.
- (Optional) Cover small scratches with a light application of shoe polish.
- Do not use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.
- Do not apply oil to your fan or motor. The motor has permanently-lubricated sealed ball bearings.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>