FLYSKY FS-R11D-ESC-BS Receiver with Gyro Stabilization User Guide

June 13, 2024
Flysky

FLY SKY LOGO

FLYSKY FS-R11D-ESC-BS Receiver with Gyro Stabilization

Introduction

FS-R11D-ESC-BS, in compliance with 2A-BS protocol, is a 2-in-1 CH11 receiver combining the Electronic Speed Control (ESC) and LED light set control board. It is equipped with a single external antenna, with the output of PWM signals and car light control signals. It can realize two-way transmission, with binding automatically upon power-up. Users can set ESC parameters at the transmitter side. FS-R11D-ESC-BS can be adapted to a variety of car models.

Receiver Overview

FLYSKY FS-R11D-ESC-BS Receiver with Gyro Stabilization
1

  1. CH1 Interface
  2. CH3 Interface
  3. CH4 Interface
  4. LED Car Light Interface
  5. CH6 Interface
  6. CH7
  7. CH8
  8. CH9
  9. CH10
  10. CH11
  11. Heatsink
  12. Motor Interface “-“
  13. Battery Interface
  14. Motor Interface “+”
  15. Power Switch
  16. LED
  17. Antenna
  18. S (CH/Car Light Interface Signal Pin)
  19. “+”(CH/Car Light Interface Anode )
  20. “-” (CH/Car Light Interface Cathode

Notes:

  1. All channel interfaces are 2.54mm*3 Pin standard pins, and the battery interface is XT60 male interface, and the spec of motor interface is a 4.0 mm bullet female connector.
  2. The LED car light interface is used to connect FS-DB01 car light drive board.

Product Specifications

  • Product Name: FS-R11D-ESC-BS
  • Adaptive Transmitters: FS-MG11-BS
  • Adaptive Models: 1 /8 crawler, on-road car, off-road short course truck, and truck
  • Number of Channels: 11
  • Number of Car Light Interfaces: 6 (LED car light interface connects to FS-DB01)
  • RF: 2.4GHz ISM
  • Maximum Power: < 20dBm (e.i.r.p.) (EU)
  • 2.4G Protocol: 2A-BS
  • Antenna: Single External Antenna(Coaxial Antenna)
  • Input Power: LiPo (2~3S)/NiMH(5~9Cell)
  • BEC Output: 6V/5A
  • Continuous / Peak Current: 60A/240A
  • Motor Type: Brushed Motor
  • Applicable Motors : 390, 370,540 or 550 Brushed Motor
  • Data Output: PWM
  • Resolution: 4096
  • Temperature Range: -10℃ ~ +60℃
  • Humidity Range: 20% ~ 95%
  • Distance: >150 M(Ground Distance without Interference)
  • WaterProof: PPX7
  • Online Update: None
  • Dimensions: 44mm30mm16.7mm
  • Weight: 45g
  • Certifications: CE, FCC ID: 2A2UNR11D00

Binding

The receiver automatically enters the binding state once it is powered on.

  1. First put the transmitter into the binding mode. (See the transmitter’s user manual for instructions on how to activate binding mode.)

  2. Turn on the receiver, and it will wait for 1 second for connection. If without connection, the receiver will enter the binding mode automatically.

  3. After the binding is successful, the receiver LED is solid on.

  4. Verify that the transmitter and receiver are working properly. If you need to re-bind, repeat the above steps.
    Notes :

  5. Set the transmitter to its binding state first, and then set the receiver to its binding state. If the binding is not finished within 10 seconds, the
    receiver LED will enter its slow flashing state.

  6. The FS-R11D-BS receiver complies with the 2A-BS protocol and is only compatible with transmitters conforming to this protocol.

Protection

This receiver has low/high voltage protection function.

  • Low Voltage Protection: When the voltage is detected to be low, CH2 has no output and all the car lights flash slowly.
  • High Voltage Protection: When the voltage is detected to be high, all channels will not output. All all the car lights flash fast.

The ESC has overheating protection function.

  • Overheating Protection: When the internal temperature of the ESC is detected to be too high, CH2 has no output and all the car lights flash fast. When the temperature is normal, the channel resumes output.

Car Light Control

This receiver features 6 sets of lights: left turn signal light, right turn signal light, daytime running light, headlight, brake light and reverse light. And these 6 sets of lights are connected to this receiver through the FS-DB01 car light driver board. The state of all the car lights is controlled by the corresponding controls of the FS-MG11-BS transmitter. The left and right turn signal lights are controlled by steering wheel. The daytime running lights and headlights are controlled by CH5 knob. The brake and reverse lights are controlled by a throttle trigger.

Notes: If you set the steering channel in reverse, the trigger condition for left and right turn signal lights will not be affected.FLYSKY FS-R11D-
ESC-BS Receiver with Gyro Stabilization 2

When the running mode of ESC is set to Forward/Reverse mode (no brake), the Brake Light will not on when pushing the throttle trigger forward.

Car Light Control

Notes:

  1. After the receiver is turned on, all the lights will be on for one second and then go out.
  2. The steering CH1 channel and throttle CH2 channel are capable of automatic neutral identifying, after the trim is adjusted, the receiver should be powered to recognize the neutral positions of these two channels automatically.

ESG Function Instruction

This receiver ESC function supports the settings of battery type, drag brake and running mode (forward/reverse, forward/reverse/brake) at the transmitter side. See the FS-MG11-BS transmitter manual for details. After the motor is connected, the receiver automatically recognizes the throttle neutral every time it is powered on.

  • When the connected battery type is lithium-ion, such as 2S LiPo, the motor fast beeps twice (3 beeps represent 3S LiPo).
  • If throttle neutral is not recognized, the motor will continue to beep quickly. There is no power output from the motor at this time.

Notes:

  1. The ESC function is available for running until the self-inspection is completed (it takes about 3 seconds). Otherwise, it may not be able to operate normally
  2. If you find that the motor steering is not correct during operation, you can set the throttle channel in reverse at the transmitter side.
  3. Normally, you must power on the transmitter and then receiver, and power off the receiver and then transmitter.

Failsafe

The failsafe function is used to protect the model and personnel when the receiver is out-of-control.

  • The CH2 (ESC ) enters the braking state in case of out-of-control, for the other channel, the failsafe can be set at the transmitter side. By default, it is not set, and the receiver will maintain the last output at the time.
  • If the FS-DB01 car light drive board is connnected to the LED car light interface, and the left and right turn signal lights are also connected, when the receiver is out-of-contro, then the left and right turn signal lights flash fast for prompt.

Attention:

  • Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
  • Please carefully check each power device and car frame instructions to ensure the power matching is reasonable before use. Avoid damaging power system due to incorrect matching.
  • Do not let the external temperature of the system exceed 90℃ /194 ℉ , because high temperature will damage the power system.
  • Make sure the receiver’s battery is disconnected before turning off the transmitter, failure to do so can result out of control. Unreasonable setting of the Failsafe may cause accidents.
  • After use, remember to disconnect the battery and the ESC. If the battery isn’t disconnected, the ESC will consume electric energy all the time even if it is off. It will discharge completely if connect the battery for a long time, thus resulting in the failure of the battery or the ESC. We are not responsible for any damage caused by this!
  • Make sure the receiver is mounted away from motors or any device that emits excessive electrical noise.
  • Keep the receiver’s antenna at least 1cm away from conductive materials such as carbon or metal.
  • Do not power on the receiver during the setup process to prevent loss of control.
  • If the throttle trim is changed on the transmitter side, the receiver needs to be re-powered to recognize the new throttle neutral. Otherwise, an exception may occur during vehicle reversing.

Certifications

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

EU DoC Declaration
Hereby, [Flysky Technology Co., Ltd.] declares that the Radio Equipment [FS- R11D-ESC-BS] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: www.flyskytech.com/info_detail/10.html

RF Exposure Compliance
The distance between user and products should be no less than 20cm.

Environmentally Friendly Disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

Manufacturer: ShenZhen FLYSKY Technology Co., Ltd.
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
http://www.flysky-cn.com
Copyright ©2023 Flysky Technology Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals