FIAMMA Vent 50 Caravan Roof Light Instruction Manual
- June 13, 2024
- FIAMMA
Table of Contents
FIAMMA Vent 50 Caravan Roof Light
Product Information
- Product Name: Rooflight VENT 50
- Available Colors: White, Crystal
- Model Numbers: 01668-0101668-02D, 01688-02D
- Weight: 4.5 kg (White), 4.7 kg (Crystal)
- Minimum Roof Thickness: 8.5 cm
- Maximum Roof Thickness: 3 cm
- Rooflight Dimensions: 50 cm x 55 cm x 57 cm
Product Usage Instructions
- Decide where the rooflight should be installed and make a square hole of 50cm. The rooflight can be installed on roofs with a thickness between 30 and 70mm. If the roof thickness is lower than 30mm, a suitable frame should be set inside the vehicle between the roof and the inside frame.
- Remove the inside frame and spread a water-proof sealant, such as SIKALASTOMER-710, THEROSTAT II, or DEKALIN 1512, over the greater part of the bottom of the outside frame to a minimum thickness of 3mm.
- Clean the bearing surface on the roof, place the outside part of the rooflight on the roof, insert the inside frame into the provided square hole, and tighten the screw from inside the vehicle to secure the rooflight external part. The screw should be tightened at least 15mm.
- Apply sealant to the whole perimeter of the outer frame and fill any gaps between the frame and the roof. Finally, insert the inside frame with the mosquito net and the blind and fit them.
- Remove the protective plastic applied to the cover, taking care not to expose the product to sunlight for too long to avoid difficulty in removing the plastic.
Please note that it is recommended to consult the website for instructions in other languages not mentioned in the manual.
Please consult the website for instructions in the languages:
NL-SV-DA-NO-FI-PT
Package contents
Check that nothing has been damaged or deformed during transport. In the event of doubts or questions concerning the installation, use or limitations of the product, contact the dealer. We recommend that the installation is carried out by qualifi ed personnel and in compliance with current local regulations.
Dimension
Installation instructions
- Decide where the roofl ight should be installed and make a square hole of 50cm. The roofl ight can be installed on roofs with thickness between 30 and 70mm. For thickness lower than 30mm set a suitable frame to be positioned on the roof inside the vehicle between the roof and the inside frame.
- Remove the inside frame and spread water-proof sealant over greater part of the bottom of the outside frame to a minimum thickness of 3mm. Recommended sealant: SIKALASTOMER-710 / THEROSTAT II / DEKALIN 1512.
- Clean the bearing surface on the roof, put the outside part of the roofl ight on the roof, insert the inside frame in the provided square hole and from inside the vehicle screw the two frames together with 12 ø4,8mm UNI EN ISO 7049 wood screws. To fi x with security the roofl ight external part, the screw must be tightened at least 15mm.
- Apply sealant to the whole perimeter of the outer frame and fi ll any gaps between the frame and the roof. Finally insert the inside frame with the mosquito net and the blind and fi t them with screws ø3,5x15mm UNI EN ISO 7049.
Remove the protective plastic applied to the cover (do not expose the product to sunlight for too long to avoid to make this operation diffi cult).
In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website for spare parts drawing.
Instructions for use
- Fiamma declines all responsibility for any personal injury and damage to property due to incorrect assembly or use of the product; it is suggested to keep the instructions inside the vehicle.
- The assembly of the product must be carried out according to the assembly instructions: the product must not be modifi ed in any way.
- Before proceeding with assembly, check that the roof thickness is compatible with the product.
Before choosing the place where to assembly the rooflight, check that:
- the product doesn’t interfere with adjacent accessories (luggage racks, cables, reinforcements in the roof, cabinets inside the passenger compartment).
- the internal and external surface of the roof is fl at.
Periodically check the tightness of all the screws in the roofl ight, especially after the fi rst kilometres from the installation and always before and after long trips. If the opening-closing device hardens, lubricate the lid opening device with a few drops of grease. It is forbidden to walk on the product cover. Before starting the vehicle, check that the roofl ight is properly closed. Periodically check that the cover is intact. Don’t open the roofl ight when the vehicle is travelling. Don’t open the roofl ight in case of strong wind or rain. Remove snow or ice from the roofl ight. Always comply with speed limits and the Highway Code. The speed should always be suitable to traffi c conditions and transported load.
In the event of an accident involving the vehicle and/or the product, ensure that the product has not been damaged. In the event of damage, contact your local retailer before moving the vehicle. Fiamma declines every responsibility for any modifi cation of the product that may cause damage and/or injury to things and people.
CARE AND MAINTENANCE
- For the internal and external cleaning of the roofl ight, always use only neutral, non-aggressive detergents. For cleaning the Crystal cover use an acrylic glass cleaner with a soft cloth so as not to scratch the surface. Never use aggressive products such as glass cleaners, all-purpose cleaners, abrasives or dish-washing detergents.
- Also, never use alcohol-containing detergents, solvents or any corrosive liquid. Clean the mosquito net with water and neutral detergent removing the roller blind and the four fastening screws.
Accessories
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.
Fiamma S.p.A. – Italy
Via San Rocco, 56 21010 Cardano al Campo (VA)
Fiamma S.p.A.
reserves the right to modify at any time, without notice, prices, materials,
specifi cations and models or to cease production of any model.
All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>