ANYSUN B09HSC4Q8Y Sewer Camera with Locator User Manual

512Hz LOCATOR USER MANUAL

SPECIFICATIONS

Sonde/Camera Locator :

Introduction

Effective and ideal tool for locating camera inspection systems. sondes and any utilities that emit 512hz frequency.
The ANYSUN CR512R is an effective locator that helps inspect sewers and drainage. Although the ANYSUN CR512R pairs perfectly with other ANYSUN inspection system. it will still work with other manufacturer’s camera or sonde system that emits 512hz frequency. Before using on your first job, make sure you understand how the system works.
The CR512R is designed to be intuitive and require minimum of training for effective use of the instrument. The controls and the information display area are large and easy to understand. Yet they include everything necessary to control the locator.
The following sections will take you through all the steps necessary to use your equipment We strongly recommend that you pay close attention to the section ‘Getting to know your tools’, and come back to it whenever you are confused about the responses you are seeing on actual locating jobs.
Please note: These instructions should be considered guidehnes. Every locating job presents unique challenges, and although most will yield to “textbook* procedures as described here, many will require a creative approach. We strongly advise that you farrikarize yourself with the fundamentals of analog locating described in the getting to know your tools’ section. Armed with this knowledge will grant you the ability to solve any issues when searching for pipes.

Know your Analog Locator

GENERAL LAYOUT

• ON/OFF, Signal Sensitivity Knob — Turn knob to turn ON/OFF. When starting off set sensitivity to max and slowly turn knob counter-clockwise to reduce sensitivity to have a more accurate reading.
• Near/Far Switch — Controls overall sensitivity. The “Far” position is recommended when starting to locate the sonde. As you approach the transmitter and the meter goes to the right at “6” and you can’t reduce the sensitivity any further, switch to “Near” to pinpoint its precise location.
• Peak Signal Indicator — Indicates the strength of the peak signal (to the right) and the null signal (to the left), make sure you can know the signal is strang or weak.
• Speaker — The receiver will emit a continuous beep when it receives a signal, and an intermittent beep when it does not receive a signal, depending on the transmitter use case.
• Signal Indicator — Green light will light up when a signal (512Hz) is received from the transmitter. You can find the transmission with accuracy and without worry of false spike or voids that can complicate the location process. (Only when the 512Hz signal from the transmitter is received will the light come on, which can effectively exclude interference signals).
• Battery Indicator — Shows the status of the battery level.

Getting to Know your Tools

• Your CRS12R locator supports the detection of any standard 512 Hz sonde or camera in the market.
• This type of sonde or camera is usually attached to devices that are sant through non-matallic sawer-lines or water pipes. The emittad magnetic field easily passes through the walls of such pipes.
• When the signals being tracked by the locator is produced by the sonde or camera, there are some differenc- es in the way the receiver is used when compared with normal cable or pipe tracing.
• Due to the nature and strength of the sonde signal, it is necassary to have some idea of where the sonde is located. This is usually not much of a problem, since the sonde is “guided” by a davice under contro! of the work crew, often with a camera attached to it.

How to Operate the 512hz Locator

The monitor in the sewer camera shows what is wrong with your sewer tunnels clearly when we push the sewer camera head into the pipeline. But we still can’t pinpoint the problematic location.
With this 512hz locator, this problem is solved.

• Step 1; Power ON the locator and mark if any other transmission is being transmitted and mark to avoid any misleading signals.

• Step 2: Tum on the sewer camera system with camera probe on and transmitting §12  frequency.

• Step 3: Keep the locator parallel to the ground and locator at hip waist length, then set locator to FAR MODE (Detect Distance: 23 feet) as well as set the signal Sensitivity Knob all the way to the right.

• Step 4: Walk around and pay attention to the Peak Signal Indicator to ensure it’s to the right at “6” and when the transmission is picked up the Green LED light will light up “Signal indictor’.

• Step 5: Walk around and adjust the sensitivity knob counter-clockwise to reduce the sensitivity and continue to observe that the indictor light is green to ensure you are within line of the sonde and that peak signal is at “6”.

• Step 6: Change from FAR MODE to NEAR MODE (Detecting Distance: 13 feet) when the sensitivity knob cannot be turned counter-clockwise anymore and the peak signal is still within range. And set the signal Sensitivity Knob all the way to the right.

• Step 7: Walk around and adjust the sensitivity knob counter-clockwise to reduce the sensitivity and continue to observe that the indictor light is green to ensure you are within line of the sonde and that peak signal is at “6”.

• Step 8: The sensitivity knob is around the left and the green LED light is still lit and the peak signal indicator is all the way to the right at “6”, Congratulations, you are right around the sonde and located the transmission.

Q&A

Q: The locator doesn’t work

A: Please check the battery and ensure battery is above 75%. check the inspection system to ensure it’s powered on and providing power to the camera probe with the sonde.
Please feel free to contact us at support@anysuntech.com with your amazon order number if you have any questions or concern. You can also send us your phone number if needed. We will reply you within 24 hrs.
The accessories that are included with this instrument are:

• Soft padded carry case
• 512 Hz Locator
• Operation Manual

Techniechnical Support

• Anysun offers technical support and sales. For any reason regarding usage and application please contact our technical support team at: support@anysuntech.com
• You can also contact us by Amazon by taking the following steps below:
  1. Sign in to your Amazon account.
  2. Click “Your Account”, then select “Your Orders”.
  3. Click “Contact Seller’ which can be located next to order.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>