unitech SP320B Bluetooth Mobile Printer User Guide

**unitech SP320B Bluetooth Mobile Printer User Guide

**

Package Content

Standard Accessories

• SP320

• Battery

• Power charger

• Thermal paper*1

• USB cable

• Belt boccia

• Quik Stat Guide

The pictures are for reference only. If any item is damaged or missing, please contact the supplier.
For Belt buckle installation, please visit http://www.ute.com/ to view SP320 User’s Manual.

Appearance and Components

Front View

Preparation before Using

Battery Installation

The battery is not installed in the printer before the product leaves factory.

1. Remove the protective film of battery contacts.

2. Install the battery as shown n the figure above.

3. Fasten the battery.

Printing Paper Roll Installation

1. Pross the cover opening button (o 6pen the paper bin cover.

2. Load paper roln to the paper bin according 1o the direction as shown n the figure.

3. Pullout a part of paper Rolland close the paper bin cover.

4. Toer of the excessive paper according o th dinocton as shown i the figure.

Note

1.  Papers pacification used by theorizer: Paper widi80mm (One s can bo adjustor) paper o dimeter: Smm,
2. Pay atenton o th diection of papar ol I s paced n e wrong dircton
3. B sure 10 puta partof paer out of he paper bin

Battery Charging

Plug the charger plug into the power socket, and the charger USB plug into the printer charging port.(AC:100V~240V/(50/60Hz)

WARNING
If use a power adapter not povided or approved by us, e prinr may be damaged.
ATENTION D ot remove the batery whils charging

Note ‘You can print while charging,

Basic Functions

Basic Functions
Power On: press and hold the POWER button fo 3 seconds. Power Off: When the printers o, press and held the POWER button FEED: Press the FEED button (under continuous feeding modo, press FEED button o feed paper of about Sum; under billback Iabel mode, press FEED button to feed paper (o seam label or black label.) Auto sleep/wake: When the printer is tumed on and has no button operation or data transmission withn 10 seconds, it wil automatically onter sleep mood. Press POWER button to wake up the printer (the printer will automatically wake up when data is receive).

Setting

Enter setting screen : During power-on state (non-sleep mode). press and hold SET button to enter the option screen.
Press SET button: Go to the next option.
Press FEED button: Change option parameters.
Press POWER button: Confirm settings and exit

| Printselftest page| Press Power button o start priming sweetest page.
---|---|---
| 0-4| Set wide range definition (coarse tuning)
| 0-4| Set small range definition (fine tuning)
| 0-4| Set print speed
| English| Set Language
| Open| Set Whether To turn on the buzzer
| Label| ‘Setaccording to the paper type used
| TSPL/ECS or CPCLESC| Set command mode
| 80/58 mm| Set according to the paper width
| 1-5hrs| Set auto shutdown
| 101301601995| Set screensaver time

Printer Parameters

Printer Parameters

Printing method| Thermal line printing
Printing paper width| 3772mm
Paper Warehouse Capacity| 550mm
Printing speed| 90mm per second
Resolution| 203dpi (8dotsi’mml
Fonts| GB 18030ASCII font (8×16.12×24,16×32), GBK (16×16.24×24,32×32), BIG5 (16×16,32×32)Unicode (UTF8)
Printer core life| 50km for thermal label150km for thermal paper! receipt (25% print density or the following)/ Each point 1.5 million pulses
Command set| ESC!POS CPCL TSPL(compatibility)
Print length| > 300m
Battery specification| 7 4V 2700mAh rechargeable Li-ion battery
Charging time| < 4 hours
Wire communication| Type-C
Wireless communication| Dual-mode Bluetooth 5.0 (SPP+BLE)
Dimensions| 140mmx117mmx6Omm
Weight| 450g
Working environment| Temperature: 0°C-45°C humidity: 20•-85%
Storage environment| Temperature        10tC-60t, humidity. 10%-90%
Print content| 10 barcode: UPC-A, UPC-E, EAN-13. EAN-8,Code39 ITF. Codebar Code93, Code128, 12/5 2D barcode QR oode,PDF417, DataMatrix

Repair and Maintenance

Daily Maintenance of Printer

1. Cleaning of outside and paper bin: Wipe the surface of the printer and the inside of the paper bin gently with a wrung-out wet cloth. Make sure that the wet cloth is completely wrung out.
2. Cleaning of printer mechanism: The printer mechanism must be cleaned regularly, especially when the print quality declines. The cleaning method is as follows: Use absorbent cotton moistened with anhydrous alcohol to gently wipe the area marked with a gray box until it is clean.
3. If water is found inside the printer, turn it off immediately, remove the battery, and dry the printer by airing.
4. If the printer will not be used for a long time, remove the battery and store it separately.

Use and Storage of Printing Paper

1. Please keep newly purchased printing paper in intact package and prevent it from direct sunlight and high temperature.
2. Please keep printed documents in a dark place at room temperature (about 20°C), so as to effectively extend the storage life of the documents.
3. If the documents need to be kept for a long time, please use long- lasting thermal printing paper.

Troubleshooting

paper with better color rendenng
Printed documents are blurred In months or even weeks| Poor quality of printing paper| Please use long-lasting thermal printing paper.
Documents are kept at high ambient temperature| Please keep the documents at room temperature.(about 20’C)

Battery Recycling

This product uses a rechargeable lithium battery. To protect the environment, please do not dispose of used batteries at will. Need to send used batteries to the designated recycling box.
FCC WARNING :

Any changes expressly or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the printer will not be used for a long time, remove the battery and store it separately.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

http://www.ute.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>