unitech HT330 Series Rugged Handheld Terminal User Guide
- June 3, 2024
- unitech
Table of Contents
unitech HT330 Series Rugged Handheld Terminal
Package
Please make sure the following contents are in the HT330 gift box.
If something is missing or damaged, please contact your Unitech
representative.
The Package Contents
- HT330 Terminal
- Battery
- Hand Strap
- USB Type-C Cable
- Quick Start Guide
Optional Accessories
- Boot Case
- Gun Grip
- Terminal Power Adaptor
- HT330 1-Slot Charging Cradle with spare Battery Slot
- HT330 1-Slot USB Cradle with spare Battery Slot
- Power Cord for Cradle
- Glass Screen Protector
- Stylus with coil strap
Product View
- Scanner Window
- LED Indicator
- 5MP Front Camera
- 4”LCD Display
- Volume Key
- Scanner Trigger Key
- Power Key
- Function Key
- Mic
- 13MP Rear Camera
- Mic
- Battery Lock
- Speaker
- POGO Pin for Gun Grip
- Holes for Hand Strap
- Battery Cover
- POGO Pin
- USB Type-C Port
Keypad View
WARNING!
- There is a risk of fire and burns if the battery is handled improperly.
- DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water.
- DO NOT attempt to open or service the battery. Dispose of used batteries according to local recycling guidelines in your area
CAUTION!
- To ensure the unit working properly, please keep all connectors away from the contaminants staying inside of them such as dust, grease, mud, and water.
- The negligence may cause the unit with no communication, short circuited, overheated and so on. If the connector is damaged, please ensure the connector is being fully repaired before using the unit to avoid causing short circuited
Inserting Micro SD/Nano SIM Card (Phone Ver. Only)
Inserting the Nano SIM Card
Push up the SIM card holder to unlock and flip the card holder to insert SIM
card. Close the card holder and slide down to lock. Ensure that it is
installed properly
Inserting the Micro SD Card
Push the SD card holder to the right to unlock and flip the card holder to
insert the SIM card. Close the card holder andpush to the left to lock. Ensure
that it is installed properly
Install the Battery Cover
Insert the battery cover in the direction as shown in the picture below:
- There are three hooks on the bottom of battery cover, align the hooks with the recesses on the battery compartment
- Insert the battery cover up to 45 degrees (45°) angle, from bottom to top
- Press down the battery cover to secure in place. Make sure there is no gap between the device and the battery cover. Push the battery lock to the left to lock.
- Make sure the battery cover is securely closed, or you may not be able to turn on the terminal.
Remove the battery
Pick the battery from the bottom, and lift to remove
Remove Battery Cover to Install Battery
Remove the battery cover in the direction as shown in the picture below:
- Push the battery lock to the right to unlock.
- Grab the battery cover from the two recesses on the side, and lift to remove the battery cover
- Align the battery with the battery compartment, then push forward until you hear a click sound
- Press down 4. the battery to secure in place
Checking LED Status
If scanner app is running, LED is controlled by scanner app. No LED (Red and Green) display when battery is out. (even AC IN)
Charging the battery
Before using the terminal for the first time, you need to charge it for about
24 hours. For the regular use, you can charge the terminal for 4.5 hours to
recharge the battery to full capacity. To charge the terminal, please use the
USB charging cable or the cradle.
Connect the type-C USB cable to the USB port on HT330 and the other end of the
USB cable connect to AC power adapter into the electrical outlet on the USB
plug. The charging LED indicator on HT330 is turning red when it is in
charging state.
http://www.ute.com/
Copyright 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a
registered trademark of Unitech Electronics Co., Ltd
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>