CKESimpleKey NSPKA-7000 Nissan Replacement Keys User Guide
- June 13, 2024
- CKESimpleKey
Table of Contents
CKESimpleKey NSPKA-7000 Nissan Replacement Keys
IMPORTANT NOTES
- All existing, working keys must be present during the pairing process. Once you pair a new key, all previous keys will be erased from the memory. The others will not be functional until you pair them again.
- The new key blade MUST be cut before beginning programming. It can be cut at any local hardware store.
- Vehicle battery should be in good condition and fully charged prior to pairing the new key. Turn off headlights, radio, A/C fan, etc. to minimize battery draw during the process.
- Do not use the EZ Installer™ while the vehicle is in motion. Unplug it from the OBD port before driving the vehicle.
- Only original remote features will work, regardless of buttons included on the Simple Key. This key does not add remote features that your vehicle did not have before.
- For your security, a tamper-evident security label is installed over the EZ Installer connector. If this label is missing, damaged, or the word “VOID” appears on the EZ Installer, please exchange this Simple Key for a new one at the retailer where it was purchased.
- Before pairing, familiarize yourself with the Simple Key’s compatibility with the make, model, and year of your vehicle below.
COMPATIBILITY LOOKUP
MAKE/MODEL /YEAR /PRIMARY DIAL POSITION /ALTERNATE DIAL POSITION
NISSAN
350Z| 2004-2006| 1|
---|---|---|---
350Z| 2007| 1| 3
350Z| 2008-2009| 3|
Altima| 2005-2006| 1|
Armada| 2004-2007| 1|
Armada| 2008| 3|
Armada| 2009| 4| 3
Armada| 2010-2015| 4|
Cube| 2009-2014| 4|
Frontier| 2004-2008| 1|
Frontier| 2009| 1| 2
---|---|---|---
Frontier| 2010-2011| 2| 4
Frontier| 2012-2018| 4|
Juke| 2011-2014| 4|
Maxima| 2004-2006| 1|
Murano| 2005-2008| 1|
NV| 2013-2017| 4|
Pathfinder| 2005-2007| 1|
Pathfinder| 2008| 3|
Pathfinder| 2009-2012| 4|
Quest| 2004-2007| 1|
Quest| 2008| 3|
Quest| 2009-2010| 4|
Rogue| 2008| 3|
Rogue| 2009| 4| 3
Rogue| 2010-2015| 4|
Sentra| 2007-2008| 3|
Sentra| 2009-2018| 4|
Titan| 2004-2007| 1|
Titan| 2008| 3|
Titan| 2009| 3| 4
Titan| 2010-2015| 4|
Versa| 2007-2008| 3|
Versa| 2009-2016| 4|
Xterra| 2006-2007| 1|
Xterra| 2008| 3|
Xterra| 2009-2015| 4|
Visit CKESimpleKey.com for the most up-to-date vehicle compatibility list.
KEY PAIRING
KEY PAIRING PART 1
NOTE: The EZ Installer has on-screen instructions to guide you through pairing steps. The numbered steps below provide more detail. Read all instructions prior to starting.
Follow the instructions in the blue portion of the screen first. After you have completed the step, follow the instructions in yellow to move to the next step. For example:
- When you see the message “Press to continue,” press and release the button on the end of the EZ Installer after completing the step written in blue.
- When you see the message “Hold to confirm,” press the button on the end of the EZ Installer for 2 seconds and release after completing the step written in blue.
Instructions have timing requirements. If you wait too long between steps, your vehicle’s computer may time out, requiring you to start over. Once you begin the pairing procedure, move at a quick and even pace.
- Find your vehicle’s make, model, and year in the Compatibility Lookup. Turn the dial on the EZ Installer to the position listed for your vehicle’s make, model, and year.
- NOTE: If more than one dial position exists for your vehicle, try the PRIMARY dial position first. If you are unable to successfully pair the key, unplug the EZ Installer, remove the key, open and close the driver’s door, move the dial to the ALTERNATE position listed for your vehicle, and try again.
- Start with the vehicle in PARK and the engine OFF.
- Enter the vehicle and close all doors.
- Remove the security label from the EZ Installer and insert the EZ Installer firmly into the on-board diagnostic (OBD) port, located under the dash.
- The location of your vehicle’s OBD port can be found in your owner’s manual.
- To continue, press and hold the EZ Installer button for 2 seconds, then release.
- Make sure all keys (new and existing) are present. To continue, press and hold the EZ Installer button for 2 seconds, then release.
- Close all doors. Turn the hazard lights on. To continue, press and hold the EZ Installer button for 2 seconds, then release.
- Do not press the brake pedal during the pairing process. Press the button to continue.
- For Dial position 1 or 2, follow steps A and B below. Otherwise, skip to Step 10.
- Insert a key into the ignition and turn it to the ON position, but do not start the vehicle. Press the EZ Installer button to continue.
- Wait up to 30 seconds for the next screen to appear. Skip to Step 11.
- For Dial position 3 or 4, follow steps A, B, and C below.
- Insert a key into the ignition. Press the EZ Installer button to continue.
- Wait up to 30 seconds for the next screen to appear.
- Turn the key to the ON position, but do not start the vehicle. Press the EZ Installer button to continue.
- Turn the key to the OFF position. Then press the EZ Installer button.
- The vehicle is now in pairing mode. Press button on EZ Installer to continue.
- Turn the key to the ON position, but do not start the vehicle. The security light will flash 5 times. Then press the EZ Installer button.
- Turn the key to the OFF position and remove the key. Then press the EZ Installer button.
- To pair a second key, press and hold the EZ Installer button for 2 seconds and release.
- Insert the next key into the ignition. Press the EZ Installer button to continue.
- Turn the key to the ON position, but do not start the vehicle. The security light will flash 5 times.
- Turn the key to the OFF position. The dash lights will turn off. Remove the key. Press the EZ Installer button to continue.
- To pair additional keys, follow on screen instructions and repeat steps 15-18 above. Once you have paired all keys, press the EZ Installer button once to continue.
- To exit key pairing mode, insert one of the paired keys into the ignition again. Press the EZ Installer button to continue.
- Turn the key to the ON position and wait 3-4 seconds. Turn the key to the OFF position. Press the EZ Installer button to continue.
- Unplug the EZ Installer. If the EZ Installer is left in the OBD port for more than 5 minutes, an alarm will sound, reminding you to remove it.
- Test the key. Remove it from the ignition, reinsert it, press the brake, and start the vehicle.
- Test each key’s remote functions. The remote functions of original keys may work already. Any remotes that do not work can be paired by following the Key Pairing Part 2 steps below.
KEY PAIRING PART 2
NOTE: Try Pairing Method A first. If the EZ Installer shows an error or the remotes are not paired at the end of the procedure, try Method B.
METHOD A
- Before starting, press unlock on each remote. Any remotes that already work can be set aside and will not need to be paired again.
- Turn the EZ Installer dial to position 8 and plug it back into the OBD port, located under the dash.
- To continue, press and hold the EZ Installer button for 2 seconds, then release.
- Close all doors. Turn the hazard lights on. To continue, press and hold the button for 2 seconds, then release.
- Do not press the brake pedal during the pairing process. Press the button to continue.
- Insert a key into the ignition and turn it to the ON position, but do not start the vehicle. Press the EZ Installer button to continue.
- Wait up to 30 seconds for the next screen to appear.
- The vehicle is in remote pairing mode. Within 10 seconds, press the Lock button on the first remote to be paired. Hazard lights should flash once.
- To pair a second remote, press and hold the EZ Installer button for 2 seconds and release. Repeat step 7 above.
- Once you have paired all remotes, press the EZ Installer button once to continue.
- Turn the key to the OFF position. Press the EZ Installer button to continue.
- Turn the key to the ON position, then OFF again. Press the EZ Installer button to continue.
- Unplug the EZ Installer and test all remotes.
METHOD B
- Unplug the EZ Installer.
- Close all doors.
- Lock the doors with the driver’s power door lock switch.
- Within 5 seconds, insert the key into the ignition and fully remove it 6 times.
- The hazard lights will flash.
- Insert the key into the ignition and turn it to the ACC position.
- Within 5 seconds, press any button once on the remote you are pairing.
- The hazard lights will flash.
- To pair additional remotes, Unlock then Lock the doors using the driver’s power door lock switch.
- Within 5 seconds, press any button once on the remote you are pairing.
- The hazard lights will flash.
- When you are finished pairing remotes, turn the key to the OFF position and open the door.
- Test all remotes.
FREQUENTLY ASKED QUESTIONS
Q: Can I use the same EZ Installer on other vehicles?
A: No, the EZ Installer can only pair Simple Keys to one vehicle. You have the ability to pair additional Simple Keys to the same vehicle. Visit CKESimpleKey.com or your local retailer to purchase additional keys. If theEZ Installer sounds a single beep for 5 seconds, then beeps continuously, this signifies that the device has already been used on another vehicle.
Q: The EZ Installer sounds a single beep for 5 seconds and shows “VIN Error” on screen, then beeps continuously?
A: This signifies that the device has already been used on another vehicle. The EZ Installer can only pair Simple Keys to one vehicle. Return the Simple Key to the retailer from which you purchased it and exchange it for a new unit.
Q: The new key won’t pair to my car?
A: If the EZ Installer doesn’t pair the key to the car, the dial position is likely incorrect. If this is the case, the EZ Installer will continuously sound after you press the pairing button. Check the compatibility section on to confirm the correct dial position for your make, model and year. If an alternate dial position(s) is listed for your vehicle, unplug the EZ Installer, turn the knob to the alternate position, and try pairing again. If the key still won’t pair, please contact customer service at 888-598-8910.
Q: The EZ Installer was unplugged during the pairing process?
A: The EZ Installer must remain plugged into the OBD port until pairing is complete. If the EZ Installer becomes unplugged during the pairing process, turn the ignition to the OFF position, remove the key, and begin the pairing process again, starting with step 3.
Q: The vehicle won’t start with the new key or old keys after attempting to pair?
A: Please call Car Keys Express customer service at 888-598-8910.
FCC STATEMENT
FCC AND ISED REGULATORY STATEMENT
MODEL: NSHKL-G02X
FCC ID: X32-NSHKG020
IC: 8797A-NSHKG020
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this device not expressly approved by iKeyless LLC could void the user’s authority to operate the equipment.
MORE INFORMATION
HELP
- For help or assistance, please contact technical support at: 888-598-8910.
OTHER KEYS
Visit CarKeysExpress.com to find a variety of award-winning products, like Universal Car Keys, Universal Car Remotes, and OEM keys and remotes. New Chrysler, Dodge, Jeep, Ram, Nissan, and Infiniti Simple Keys are coming soon.
Patent: US10755506B2
Designed and assembled: in the USA 12101 Sycamore Station Place Ste. 140
Louisville, KY 40299
© 2023 Car Keys Express
www.CKESimpleKey.com